Lightolier Lytecaster 1004SIC User manual

Lightolier a Genlyte company www.lightolier.com
631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • I0806
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lytecaster®Recessed Downlighting 1004SIC
Page 1 of 1 5" Aperture 0®Shallow Incandescent Convertible IC/Non-IC Frame-in Kit
Top View
Frame-In Kit
Reflector Trim
23
6
1
7
5
4
Overall Length
1004sic/N: 9"
13" MIN.
24" MAX.
Overall Width
1004sic/n: 5 3/4”
Height
1004sic/n: 5 1/2"
1004SICN
(Integral Nail)
1004SIC
(Integral Screw)
Ceiling Opening: 5 3/8" Diameter
Feature
1. Housing: .032” (#20 ga.) Aluminum. UL listed convertible IC/NON-IC. 2"
vertical adjustment in ceiling. Can be removed for access to junction box and
ceiling plenum. 5 1/2" tall for use in 2" X 6" joist construction and shallow
plenum applications. AirSeal®housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces heat
loss and condensation in ceiling.
2. Mounting Frame: .048" (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in.) .032" (#22 ga.) galvanized steel.
UL listed for maximum of 8 (#12 ga.) 1104SIC/N and 6 (#12 ga.) 1004SIC/N
90°C through branch circuit conductors. Integral cable clamps permit
attachment of non-metallic (#12 or #14 ga.) Romex®cable without tools or
additional connectors.
4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate
16" to 24" O.C. joist spacing. Bars can accommodate 9" O.C. joist spacing
after a slight field modification (See Instruction Sheet). 1004SIC features
integral self-tapping phillips screws for secure attachment to wood or metal
construction. The 1004SICN features integral nails for secure attachment to
wood. Both attach to T-bar ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket: Porcelain medium base; nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 Volt 200° C) leads to junction box.
7. Thermal Protector: Meets NEC and UL requirements. Located inside
housing.
Options & Accessories
AirSeal®Kit: LAS56
NOTE: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible, Suitable for Damp Locations)
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight
Cone Satin Cone Baffles Basic White Wall Washer Enclosed Diffuser
1004SIC 1012 1008 1005 1071 1085* 1024*
1004SICN 1012NM 1008NM 1005WH
1013 1010 1005NM
1013WH 1010NM 1005BNM
1013CD 1076
1013NM 1076WH
1013BKNM
1013CDNM
1013BK
AirSeal®is a registered trademark of Lightolier.
Romex®is a registered trademark of General Cable Industries Inc.
*for Non-IC applications only