Sauder Shoal Creek 418662 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-26
Français p 27-29
Español p 30-32
Lot # 372703 05/13/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Armoire
Shoal Creek Collection | Model 418662
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-26
27-29
30-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
418662 www.sauder.com/servicesPae 2
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF/BOTTOM (2)
E BACK (1)
F DOOR (2)
G ADJUSTABLE SHELF (2)
H RIGHT FRONT LEG (1)
I LEFT FRONT LEG (1)
J REAR LEG (2)
K DRAWER FRONT (1)
P END MOLDING (2)
D26 RIGHT DRAWER SIDE (1)
D27 LEFT DRAWER SIDE (1)
D174 DRAWER BACK (1)
D981 DRAWER BOTTOM (1)
M64 DRAWER BRACE (1)

Part Identification
418662www.sauder.com/services Pae 3
A
B
C
D
E
F
GH
I
J
K
P
M64
J
P
F
D
G
D26
D27
D174
D981

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418662 www.sauder.com/servicesPae 4
SAFETY BRACKET - 1
1G METAL BRACKET - 2 4G
HIDDEN CAM - 21
1F
METAL PIN - 8
1R
CAM SCREW - 9
8F
SLIDE CAM - 2
10A
22H
HINGE SPACER - 4
CAM DOWEL - 12
2F
KNOB - 5
24K
SHELF SNAP - 8
6R
FELT DISC CARD - 2
1M
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1
NAIL - 43
1N
5L WARNING LABEL - 1
(Refer to Step 19 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
14H HINGE - 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418662www.sauder.com/services Pae 5
BLACK 1-1/8" MACHINE SCREW - 5
21S
BLACK 9/16" LARGE HEAD SCREW - 3
1S BLACK 1-7/8" FLAT HEAD SCREW - 1 2S
BLACK 2-1/4" FLAT HEAD SCREW - 8
26S
GOLD 5/16" FLAT HEAD SCREW - 8
3S
SILVER 5/8" FLAT HEAD SCREW - 8
23S
BLACK 9/16" FLAT HEAD SCREW - 4
32S30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push twenty-one HIDDEN CAMS (1F) into the ENDS (A
and B), SHELF/BOTTOMS (D), and DRAWER BRACE (M64).
Then, insert the metal end of twelve CAM DOWELS (2F)
into the HIDDEN CAMS, except the lon edes of the
ENDS (A and B) and the DRAWER BRACE (M64).
418662 www.sauder.com/servicesPae 6
(21 used)
(12 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
A
B
D
M64
D
Do not insert CAM DOWELS into these edes.
Do not insert CAM DOWELS into this part.
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1217
to watch a video on how to assemble your unit.

å Turn nine CAM SCREWS (8F) into the FRONT LEGS (H
and I) and DRAWER FRONT (K).
Step 2
418662www.sauder.com/services Pae 7
8F
K
H
I
(9 used)
Remember:
Rihty tihty.
Lefty loosey.

å Fasten the CABINET RIGHT (35GA) to the RIGHT
END (A) and the CABINET LEFT (35GB) to the END (B).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
Step 3
418662 www.sauder.com/servicesPae 8
1
2
3
1
2
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Lon ede with
HIDDEN CAMS
Lon ede with
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
A
Surface with
HIDDEN CAMS

å Fasten the REAR LEGS (J) to the ENDS (A and B). Use
eiht BLACK 2-1/4" FLAT HEAD SCREWS (26S).
Step 4
418662www.sauder.com/services Pae 9
B
J
J
Surface with
HIDDEN CAMS
These surfaces should be even.
Anled ede
Anled ede
BLACK 2-1/4" FLAT HEAD SCREW
(8 used in this step)
26S
A
Surface with
HIDDEN CAMS

å Fasten one of the SHELF/BOTTOMS (D) to the ENDS (A
and B). Tihten four HIDDEN CAMS.
Step 5
418662 www.sauder.com/servicesPae 10
Start Tihten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
A
B
D
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
J
J
Lon ede with
HIDDEN CAMS
Lon ede with
HIDDEN CAMS
Finished ede
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution