Furniture of America CM-BK450TF User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 10
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 16-12-09
CM-BK450TF
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 10
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 10
#1 x 1pc
Lower End Guardrail
#2 x 1pc
Lower End Guardrail
#3 x 1pc
Upper End Guardrail
#4 x 1pc
Upper End Guardrail
#5 x 1pc
Lower Front Side Rail
#6 x 1pc
Lower Back Side Rail
#7 x 1pc
Upper Front Side Rail
#8 x 1pc
Upper Back Side Rail
#9 x 1pc
Back Guardrail
#10 x 1pc
Front Guardrail
#11 x 2pcs
Ladder Rail (Left)
#12 x 1pc
Ladder Rail (Right)
#13 x 2pcs
Ladder Rung
#14 x 1pc
Ladder Rung
#16 x 1pc
Ladder Rail Support
#15 x 1pc
Ladder Rung

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 10
#17 x 2pcs
Full Slat Kit (13pcs)
#19 x 1set
Parts List
Hardware List
#A x 16pcs
Bolt Ø1/4" x 4-7/8"
#C x 8pcs
Bolt Ø1/4" x 2-3/4"
#B x 16pcs
Barrel Nut Ø1/4" x 1/2"
#D x 4pcs
Bolt Ø1/4" x 1-9/16"
#E x 8pcs
Bolt Ø1/4" x 1-3/16"
#F x 8pcs
Screw Ø1/4" x 2"
#G x 16pcs
Screw #3/16" x 1-3/16"
#H x 2pcs
Screw #3/16" x 1-9/16"
#K x 1pc
Allen Wrench 4mm
#J x 1pc
Wood Dowel Ø7/16" x 1-9/16"
#I x 4pcs
Metal Dowel Ø3/8" x 3-9/16"
#18 x 1set
Twin Slat Kit (13pcs)
Support Leg 320x40x40mm

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 5 of 10
#1
#2
#5
#6
#3
#4
#7
#8
#9
#10
#11
#12
#15
#14
#13
#16
#17
#19
#18

Page 6 of 10
#B
#K
#B
#K
#A
#A
#A x 8pcs
#B x 8pcs
#A x 8pcs
#B x 8pcs
#1
#2
#5
#6
#3
#4
#7
#8
Insert barrel nuts (#B) into side rails (#5). Align side
rails (#5,6) to the holes of the headboards (#1,2), then
secure by inserting and connecting bolts (#A) to barrel
nuts (#B).
Insert barrel nuts (#B) into side rails (#7,8) to the holes
of the upper headboard (#3,4), then secure by inserting
and connecting bolts (#A) to barrel nuts (#B).

Page 7 of 10
#K
#C
#E
#E
#K
#C x 6pcs
#E x 8pcs
#I
#I
#I
#I x 4pcs
#9
#10
#1
#2
#4
#3 #8
#7
1) Align the back guardrail (#9) to the holes of the
headboard (#3,4) and side rails (#7). Secure holes
aligned to headboard (#3,4) with bolts (#C). Secure
holes aligned to side rails (#7) with bolts (#E).
2) Align the front
guardrail (#10) to
the holes of the
headboard (#3,4)
and side rails (#8).
Secure holes aligned
to headboard (#3,4)
with bolts (#C).
Secure holes aligned
to side rails (#8)
with bolts (#E).
Insert metal dowels (#I) to the holes of the
headboards (#1,2), then place the twin
frame to the metal dowels (#I) of the full
frame.

#D
#D
Page 8 of 10
#F
#F
#K
#K
#J
#K
#C x 2pcs
#F x 8pcs
#J x 1pc
#D x 4pcs
#11
#12
#15
#13
#16
#14
#C
#K
#13
#7
#5
Align ladder rung (#13,14,15) to the holes of the ladder rails (#11,12), then secure with screws
(#F). Place wood dowel (#J) to the center hole of ladder rail support (#16). Align ladder rail
support (#16) to the holes of the ladder rail (#12), then secure with bolts (#C).
Align ladder to the holes of the side rails (#7,5), then secure with bolts (#D).

#H x 2pcs
#G
#G x 16pcs
#18
#19
Page 9 of 10
#G
#H
#17
#19
Align the support legs (#17) to the holes of the slats (#19),
then secure with screws (#H).
Align slats (#18) to the top side rails, then secure with screws (#G).
Align slats (#19) to the bottom side rails, then secure with screws
(#G).

Page 10 of 10