Lightolier F7000-18 User manual

Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems F7000-18
1BHFPG '4FSJFT-JHIU5-PVWFS8BMM.PVOU
&
Features
1. Housing: Single piece of high purity extruded aluminum, a portion from
recycled material. Extruded acrylic lens reveal installed on the top of the
housing, runs the length of the housing.
2. Housing End: Die-cast aluminum, welded in place.
3. End Cap: Die-cast aluminum. Encloses the end of the run.
4. Lamps: F28T5 or F54T5HO as specified. By others. Installed fromthe ceiling
side of the luminaire.
5. Ballast: Electronic. Meets ANSI starting, end-of-life protection and sound
rating specifications. Low THD.
6. Shielding: Integral, regressed flat louver blades punched and formed from
fixture housing, finished to match, no light leaks. Blades are 0.56” (1.42cm)
high on 0.75” (1.91cm) centers.
Electrical
Connections: Pre-wired with 18 gauge wires and polarized cannon plug con-
nectors for simultaneous mechanical/electrical connection.
Emergency Battery Pack: 90 minute operation, 700 lumens for 54W and 520
lumens for 28W.
Dimming: Advance Mark X standard (no additional wires required); use compat-
ible dimmer. Dimming ballasts using additional control wires (e.g. Lutron Hi-Lume
or ECO-10, Osram) can be used; consult factory and use X4 or X5 power feeds
with additional leads, as appropriate. Ballast not to exceed 1.25” (3.18cm) wide by
1.20” (3.05cm) high.
iGEN: F7000 accepts iGEN (DALI) with supplemental 2-wire control technology.
Use with X5 power feed.
Power Tray: Code-gauge, die-formed steel, pre-paint white enamel finish;
secured by quarter-turn fasteners for easy access to wiring. Holds ballasts, sock-
ets, and wiring. Accepts ballasts up to 1.25” (3.18cm) wide by 1.20” (3.05cm) high.
Ordering Information
Complete Ordering Instructions below.
3.25”
(8.25cm)
3.95” (10.03cm)
1.63”
(4.14cm)
FW7
Family Series
4
Type Lamps Color Wattage Voltage Length
4 1
4= Block
w/ Lens
4= Louver 1= 1 LampAL = Aluminum
WH = White
1= 28W
2= 54W
3= 28W Dimming
4= 28W EM
5= 54W Dimming
6= 54W EM
1= 120v
2= 277v
4= 4’ (121.92cm)
8= 8’ (243.84cm)
54
1
1
3.698”
(9.39cm)
1.304”
(3.31cm)
.750”
(1.91cm)
6. Louver Shielding
Mounting
Each module includes two wall-mounting brackets. Bracket hole pattern accom-
modates junction box (single gang box rotated 90 degrees) or other appropriate
mounting method using customer supplied fasteners.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order one MODULE.
2. Order one END SET.
Continuous Rows:
1. Order the appropriate number of MODULES for the complete run.
2. Order one END SET.
Finish
Powder-coated, baked enamel, white or aluminum, as specified.
Factory installed ballast disconnect allows the ballast to be disconnected fromand
reconnected to incoming power under load without turning the entire circuit off.

Job Information Type:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems F7000-18
1BHFPG '4FSJFT-JHIU5-PVWFS8BMM.PVOU
&
CANDLEPOWER
ZONE 0 22 45 67 90
DEG. CANDELAS
0 618 618 618 618 618
5 631 627 624 612 606
15 701 672 618 559 532
25 787 717 597 488 433
35 712 667 548 394 319
45 462 442 402 282 206
55 286 264 225 173 123
65 191 171 144 118 80
75 133 129 108 78 42
85 107 98 74 43 8
90 92 84 61 31 0
95 127 126 113 98 35
105 350 355 345 313 155
115 611 613 581 433 285
125 818 789 675 543 412
135 841 817 738 621 515
145 844 828 771 664 600
155 822 813 762 688 661
165 756 749 727 700 700
175 699 700 707 710 713
180 710 710 710 710 710
Performance
CANDLEPOWER CURVE
840
630
420
210
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
REPORT NO.: ITL54690.IES
LAMPS: 1-F54T5
LUMENS: 5000 each
EFFICIENCY: 81.7%
CAT. NO.: F7441WH214
DISTRIBUTION
Zone Lumens % Lamp %Luminaire
0 - 90 1339 26.6 33.0
90 - 180 2748 55.1 67.0
0 - 180 4087 81.7 100.0
80% 70% 50%
50 30 10 50 30 10 50 30 10
0 858585 7676 76 616161
1 737067 6764 62 535149
2 656056 5854 50 474442
3 575147 5147 43 423835
4 504540 4641 36 373330
5 453934 4135 31 332926
6 403429 3731 28 292623
7 363026 3328 24 272320
8 332723 3025 21 252118
9 302420 2822 19 231916
10 28 22 18 26 20 17 21 17 14
20% FLOOR CAVITY REFLECTANCE
COEFFICIENTS OF UTILIZATION
% EFFECTIVE CEILING CAVITY REFLECTANCE
WALL REFLECTANCE
ROOM CAVITY RATIO
Mounting Accessories
Wall Mount End Set
FW7EWH = White
FW7EAL = Aluminum
Fixture Lengths & Mounting Reflected (Plan View)
20'-3" (617.22cm)
16'-3" (495.30cm)
12'-3" (373.38cm)
8'-3" (251.46cm)4'-3" (129.54cm)
2'-8"
(81.28cm)6'-8" (203.20cm)
6'-8" (203.20cm)2'-8"
(81.28cm)
1'-4"
(40.64cm)
6'-8" (203.20cm)1'-4"
(40.64cm)6'-8" (203.20cm)
6'-8" (203.20cm)1'-4"
(40.64cm)6'-8" (203.20cm)2'-8"
(81.28cm)
1'-4"
(40.64cm)
16.00" (40.64cm)
3/4"
(1.91cm)
1-1/2"
(3.81cm)
3/8" (0.95cm)
END OF ROW DETAIL
GAP BETWEEN FIXTURES
JOINING DETAIL
Recommended mounting is a single gang outlet box rotated 90 degrees at the
feed point. Remaining mounting points could be outlet boxes as well, or a couple
of holes per mounting point spaced 3-1/4” (8.26cm) at 1-3/4” (4.45cm) above the
bottomof fixture.