LIGHTSAFE EDLED User manual

EDLED Instructions Rev01
EDLED
Surface 3 hour Maintained LED Drop Light
We are delighted that you have purchased this Light fitting. Please read this instruction manual before installation and retain
for the user maintenance engineer for future reference.
Our products are designed to comply with the recommendations of BS EN 60598-1:2008 code of practice for emergency
lighting of premises and be installed by a competent person in accordance with the relevant wiring regulations.
IMPORTANT NOTE:
Installation must be carried out by a skilled competent electrician who is familiar with the appropriate standards and
technical requirements of the appliance and also taking in to consideration the latest building regulations.
Not suitable for use with dimmer switches, Install in accordance with I.E.E. Wiring Regulations.
This product must e earthed and NOT be subject to an electrical insulation test (500 1000v)
For Maintained Operation-For lamp always on,link Ls(Switched Live) to terminal L(Permanent Live).If ‘Ls’ not connected,
fitting works as non-maintained.
Please note: The LED’s contained in this fitting are not designed to be replaced.
INSTALLATION
1. Remove the diffuser from the body by removing the two screws.
2. Release the hinged gear tray by releasing the two plastic retaining clips and remove the gear tray.
3. Fix base to the ceiling.
4. Ensure the mains supply is isolated. There are four 20mm cable entries, drill the require entry most suitable for the
installation.
5. The fitting requires a permanent 230v AC supply to the live (L), Earth and neutral (N) terminals on the PCB. This would
be as per non-maintained mode to charge the batteries. For the maintained circuits for continuous illumination this can
be achieved by connecting a link between L and L1 (default) or to have a switch live connection through a remote switch
to the L1 connection. Ensure ALL electrical connections are tight with no loose strands.
6. Plug the battery lead into connector on the PCB.
7. Re-secure the gear tray into the base of the unit making sure that the mains cable is not trapped by the PCB.
8. Refit the diffuser using the two screws.
9. Restore the mains supply, the green charge LED should be illuminate
10. Ensure the fitting is charged for a minimum of 24 hours prior to testing
IMPORTANT: To extend battery life always fit the luminaire with the batteries at the bottom when wall mounting.
11. Connect the mains supply wiring as follows:
Ensure that all connection are firmly secured and there are no loose strands omitted
12. For component protection in transit and user safety the luminaire battery fuse is supplied separately in the fitting.
Once the fitting is installed and wired correctly the battery fuse must be installed in the fuse holder on the PCB.
13. When all connections have been made reassemble the fitting completely.
14. Restore the supply and check that the Green LED indicator illuminates to confirm the batteries are charging.

EDLED Instructions Rev01
15. Allow a short period for part charging of the batteries and then isolate the mains supply to the fitting in order to check
the correct operation of the fitting in emergency mode.After 36 hours on continuous charge (and only at a safe time) a
mains failure should be simulated to ensure that the fitting illuminates for is rated emergency duration.
The luminaire will have 1 hour backup after 14 hour charge and will be full charged after 24 hours.
Once the luminaire no longer meets its rated emergency operation the batteries must be replaced, regardless, all batteries
must be replaced after a maximum of 4 years in service.
Subsequent testing should be carried out in accordance with the British European standards.
Maintenance
Repairs should only be carried out by suitably qualified person.
Special care should be taken if it’s required to open the fitting for lamping as the fitting may still be “live” even though the
mains supply has been isolated. In these circumstances immediately disconnect the battery supply.
Servicing, cleaning, lamp replacement etc should only be carried out after the fitting has been made electrically safe.
Cleaning of luminaires should be carried out at regular intervals not only to ensure good optical performance but also ensure
that dirt does not accumulate to such an extent as to impair the electrical or thermal safety of the fitting.
Technical Specification:
Voltage: 220-240 V~ 50Hz
Lamp: 27 x 0.05W LED
Wattage: 1.3W
Colour Temp: 6000k
Lumen Output: 61lm
Class: 1
Battery: 3.6V 1.5Ah NiCad
Emergency Duration: 3 Hour
Recharge Time: 24 hours, Initial charge 36 hours
Fuse: Mains fuse 5x20mm 0.5A, Battery fuse 5x20mm 1A
Temp Range: 0℃ - 40℃
Dimensions: 352x110x223mm
IP: IP65
The date of the commissioning of the battery should be added to the label on the battery.
WARRANTY
This product has a 2 year warranty
Due to our policy of continuous improvement we reserve the right to change specification without prior notice.
Errors and omissions excepted. These instructions have been carefully checked prior to publication. However, no
responsibility can be accepted by Firesafe for any misinterpretation of these instructions.
LIGHTSAFE
Distributed by: FIRESAFE
10 Sandersons Way, Marton,
Blackpool, FY4 4NB
Tel: [phone], Fax: [phone]
Technical: 01253 760 800
Email: [e-mail]
Web: www.firesafe.co.uk