Lilin PS3108C User manual

i
PS3108C
8-Port Web Smart GbE PoE+ Switch
QUICK INSTALLATION GUIDE

ii
Contents
Chapter 1 Introduction......................................................................1
Overview.......................................................................................................... 1
Front panel of the Switch ................................................................................. 1
Rear panel of the Switch.................................................................................. 2
Chapter 2 Installing The Switch ......................................................3
Package Contents............................................................................................ 4
Mounting the Switch in a 19-inch Rack ............................................................ 4
Mounting the Switch on Desk or Shelf ............................................................. 5
Connecting the AC Power Cord ....................................................................... 6
Installing SFP Modules .................................................................................... 6
Chapter 3 Managing Switch Using the Web Interface ...................7
Manage the Switch Using Web Browser.......................................................... 7
Chapter 4 Troubleshooting..............................................................8
Appendix A Technical Specifications ................................................9
Hardware Specification .................................................................................... 9
1000 MBPS Gigabit Ethernet Collision Domain ............................................. 10

1
Chapter 1 Introduction
Overview
PS3108C is a 10 ports PoE GbE Web Smart+ Switch. PS3108C provide high-performance, IEEE-
compliant network solutions. They include powerful management features that you can use to boost
performance, and increase productivity.
This guide describes hardware installation and basic troubleshooting for these managed switches.
Front panel of the Switch
Figure 1 Front panel of the switch
Table 1 Port Status LEDs
LED
Condition
Status
TP (Link/Act/Speed)
Green/Blink
Lit Green when TP link on 1000Mbps
Amber when TP link on 10/100Mbps
TP (PoE)
Green/Off
Lit Green when PoE link good
SFP (Link/Act/Speed)
Green/Blink
Lit Green when SFP link good
Lit Green when SFP link on 1000Mbps.
Amber when SFP link on 100Mbps

2
Table 2 System Status LED
SYSTEM LED
Condition
status
System
Green
OFF
Lit when power is coming up
Table 3 Mode Status LED
LED
Condition
Status
Link/ACT/Speed
Green
Yellow
OFF
Green when the link on 1000Mbps
Yellow when the link on 100Mbps
Off when the link on 10Mbps
PoE
Green
OFF
Lit Green shows all LED of each port are in PoE
Mode
Rear panel of the Switch
Figure 2 Rear panel of the switch
AC Power Socket

3
Chapter 2 Installing The Switch
C AUTION : Circuit devices are sensitive to static electricity, which can
damage their delicate electronics. Dry weather conditions or walking
across a carpeted floor may cause you to acquire a static electrical
charge.
To protect your device, always:
•Touch the metal chassis of your computer to ground the static
electrical charge before you pick up the circuit device.
•Pick up the device by hold it on the left and right edges only.
•If you use outdoor device connected to switch with cable then you
need to install a surge arrester in between outdoor device and switch.
Figure 3 Add a surge arrester between outdoor device and switch
NOTE:The switch is an indoor device; if it is to be used with outdoor
devices such as outdoor IP camera or outdoor WiFi AP, then users
must install a surge arrester to protect the switch
W ARNING :
•Self-demolition on Product is strictly prohibited. Damage caused by
self-demolition will be charged for repairing fees.
•Do not place the switch in outdoor environment.
•Before installation, please make sure the input power source meeting
the product specification
•Before importing / exporting configuration file, please make sure the
firmware version is always the same.

4
Package Contents
PS3108C GbE Management Switch
Four adhesive rubber feet
Mounting Accessory (for 19” Rack Shelf, Optional)
Installation Guide
AC Power cord
Mounting the Switch in a 19-inch Rack
Step1. Attach the mounting brackets to both sides of the chassis with screws.
Figure 4 Attaching mounting brackets to the switch
Step2. Place the switch on a rack shelf in the rack. Push the switch in until the oval holes in the
brackets align with the mounting holes in the rack posts.
Step3. Attach the mounting brackets to the rack posts with screws.

5
Figure 5 Attaching mounting brackets to the rack post
Mounting the Switch on Desk or Shelf
Step1. Verify that the workbench is sturdy and reliably grounded.
Step2. The rubber feet are included in the accessory kit. Attach the four adhesive rubber feet to the
bottom of the switch.
Figure 6 Attaching the Rubber Feet

6
Connecting the AC Power Cord
Figure 7 Connecting the AC power cord to the AC power receptacle
Step1. Connect one end of the AC power cord to the AC power receptacle on the switch.
Step2. Connect the other end of the AC power cord to the AC power outlet.
Step3. Examine the power LED. If it is ON, the power connection is correct.
Installing SFP Modules
You can install or remove a mini-GBIC SFP from a mini-GBIC slot without having to power off the
switch. Use only Manufacture mini-GBIC:
Step1. Insert the module into the switch port.
Step2. Press firmly to ensure that the module seats into the connector.
Figure 8 Installing a SFP Module into a SFP Module Slot

7
Chapter 3 Managing Switch Using the Web Interface
Manage the Switch Using Web Browser
After you power up the switch for the first time, you can configure the switch using a web browser. For
more information about managing the switch, see the user interface manual.
Figure 9 Web Interface login page
Step1. Power on the computer and the switch.
Step2. Plug in the power cable.
Step3. Set the IP configuration on your computer.
NOTE:
1. If the switch is using the factory default IP address of 192.168.0.1,
you must chose an IP address for the computer in the range of
192.168.0.1—192.168.0.253 that is not already in use.
2. If the IP addresses is assigned by a DHCP server, make sure the
DHCP server is running and can be reached from the switch and
the computer. It might be necessary to disconnect and reconnect
the devices for them to discover their new IP addresses from the
DHCP server.
Step4. Enter the user name and password (The default username is “admin” and password is
“admin”.), and then click “Login” to login to the switch configuration window.

8
Chapter 4 Troubleshooting
Troubleshooting Chart
The following table lists Issues, Causes, and Action to possible problems.
Table 4 Troubleshooting Chart
Issues
Cause
Action
SYSTEM LED Off
No power is received.
Check the power cord connections for the
switch at the switch and the connected
device.
Make sure that all cables used are correct
and comply with Ethernet specifications.
Link LED Off
Port connection is not working.
•Check the crimp on the connectors.
Make sure that the plug is fully
inserted and locked into the port at
both the switch and the connecting
device.
•Make sure that all cables used are
correct and comply with Ethernet
specifications.
•Check for a defective adapter card,
cable, or port by testing it in an
alternate environment where all
products are functioning.
Slow file transfer
or there is
performance
degradation.
Half- or full-duplex setting on
the switch and the connected
device are not the same.
•Make sure that the attached device is
set to auto negotiate.
•Check the system message log.
Device is not
recognized as
part of the
network.
One or more devices are not
properly connected, or cabling
does not meet Ethernet
guidelines.
Verify that the cabling is correct. Be sure
that all connectors are securely positioned
in the required ports. Equipment might
have been accidentally disconnected.

9
Appendix A Technical Specifications
Hardware Specification
Table 5 Hardware Specification
Port Configuration
10M/100M/1G RJ45 Port
8
100M/1G/2.5G RJ45 Port
--
100M/1G/10G RJ45 Port
--
100M/1G SFP Port
--
1G/2.5G SFP Port
--
1G/10G SFP+ Port
--
GbE RJ45/SFP Combo Port
2
Console Port
--
Total Ports
10
PoE Function
IEEE802.3at (PoE+ 30W)
Y
IEEE802.3af (PoE 15.4W)
Y
UPoE(60W)
--
PoE Port
8
Available PoE Power
130W
HW Performance
Switching Bandwidth
20Gbps
Forwarding Performance
14.9Mpps
MAC Address
8K
Jumbo Frames
9216 Bytes
Environemental Specification
Operating Temperature
0°C to 45°C
Operating Humidity
10 to 90% RH
Storage Temperature
-20 to 70°C
Storage Humidity
10 to 90% RH
Mechanical Specification
Dimensions (H) x (W) x (D) mm
44 x 220 x 242
Weight
2.1 Kg
FAN Less
Y
Power Source
AC Input
100V-240V
DC Input
--
AC/DC Dual Input
--

10
1000 MBPS Gigabit Ethernet Collision Domain
Table 6 Maximum 1000BASE-T Gigabit Ethernet Cable Length
Cable Type
Maximum Cable Length
Connector
Category 5, 5e or 6 100-ohm UTP
or STP
100.m (328 ft)
RJ-45
Table 7 Maximum 1000BASE-SX Gigabit Fiber Cable Length
Fiber Size
Fiber Bandwidth
Maximum Cable Length
Connector
62.5/125 micron
multimode fiber
160 MHz/km
200 MHz/km
220 m (722 ft)
275 m (902 ft)
LC
LC
50/125 micron
multimode fiber
400 MHz/km
500 MHz/km
500 m (1641 ft)
550 m (1805 ft)
LC
LC
Table 8 Maximum 1000BASE-LX/LHX/XD/ZX Gigabit Fiber Cable Length
Fiber Size
Fiber Bandwidth
Maximum Cable Length
Connector
9/125 micron single-
mode fiber 1310nm
N/A
10km (6.2 miles)
LC
9/125 micron single-
mode fiber 1550nm
N/A
30km (18.64 miles)
50km (31.06 miles)
LC
LC
Table 9 Maximum 1000BASE-LX Single Fiber Gigabit Fiber Cable Length
Fiber Size
Fiber Bandwidth
Maximum Cable Length
Connector
Single-mode
TX-1310nm
RX-1550nm
N/A
20km (12.42miles)
BIDI
LC
Single-mode
TX-1550nm
RX-1310nm
N/A
20km (12.42miles)
BIDI
LC