Lincat OE8306 Owner's manual

IS 609 ECN 3977 Page 1 of 9
Installation, Operating and Servicing
Instructions
Opus 800 Electric Cook & Hold Salamander
OE8306
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

IS 609 ECN 3977 Page 2 of 9
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
4-5
Operating Instructions
6-7
Cleaning
7
Servicing, Maintenance and Component Replacement
7-9
Fault Finding
9
Spare Parts List
9
Accessories
10
Service Information and Guarantee
11
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 609 ECN 3977 Page 3 of 9
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Height (mm)
510
Width (mm)
600
Depth (mm)
520
Weight (kg)
60
Cooking area w x d (mm)
530 x 340
Number of individually controlled heat zones
3
Heat input per element (watts)
1500
Total heat input (kW)
4.5
Electricity supply 1N~+e 230V 50-60Hz
Current Rating (Amps)
19.6
Electricity supply 3N~+e 400V 50-60Hz
Current Rating (Amps)
L1 –6.5
L2 –6.5
L3 –6.5
*NB. Appliances are 600mm deep when wall mounted.
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Collection tray
Chrome plated grilling rack
Wire tray
Heat shield

IS 609 ECN 3977 Page 4 of 9
INSTALLATION AND COMMISSIONING
This product is heavy; prior to installation a handling assessment should be made.
This appliance must be earthed. An equipotential bonding terminal is provided to
allow cross bonding with other equipment.
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of this appliance.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of at least 60 Deg C.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57).
This appliance may be counter or wall mounted. For either installation, remove and
discard the 2 transportation screws (A) from rear panel (Fig 2).
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material (see Fig 2).
Minimum distances A 300mm B 500mm.
Do not install above any heat source the unit vents from the underside and this
could cause the unit too over heat.
Warning: During installation do not place on surfaces or near walls, partitions or
kitchen furniture and a like –unless they are made of non-combustible material or
clad with non-combustible heating-insulating material, and pay attention to fire
prevention regulations.
Electrical connection
The electrical supply cable enters the unit through a cable gland in the rear panel
with access via a removable side panel(see Fig 1).
Connection of the electrical supply cable is to a terminal block behind the side
panel. Open the protective cover on the terminal housing where indicated using a
flat bladed screwdriver. Fit a suitable cable into the strain relief and then to the
terminal block.
A
A
Fig 1

IS 609 ECN 3977 Page 5 of 9
Fig 2

IS 609 ECN 3977 Page 6 of 9
OPERATING INSTRUCTIONS
Electronic display and control
A B C D E
F G H I
Fig 2
A On/Off Button –Left Heating Element
BOn/Off Button –Centre Heating Element
COn/Off Button –Right Heating Element
D Digital Display
EOn/Off isolating switch
FCook/Hold Function Button (cycles through Cook –Hold –Cook and Hold)
GStart/Stop Key
HControl for setting either time and hold level setting
ITimer 0-20mins / Hold setting 1-6 Encoder Knob
Only qualified or trained personnel should use this appliance.
This appliance has 3 cooking modes Cook –Hold –Cook & Hold these are
indicated with the illumination of the LED on button (F)
(The switching between the different cooking modes is allowed only in stop)
Cook Hold Cook & Hold
Switching on
After turning on the unit it will always remember the last setting used.
Cook
Select the cook mode F.
Select heating element On/Off A/B/C.
Adjust height of the hood to desired position.
Cycle time required 0-20mins I.
Start the unit Gor activate the plate detection.
(The LED will flash during the cooking cycle)
Note: At cycle end the buzzer will sound and “End” is displayed.

IS 609 ECN 3977 Page 7 of 9
Hold
Select the hold mode F.
Select heating element On/Off A/B/C.
Adjust height of the hood to desired position.
Select the hold level from level 1 to 6 I.
Start the unit Gor activate the plate detection.
(The LED will flash during hold activation)
Note: The hold mode has no end time, it works until the stop key is pressed.
Cook & Hold
Select the cook & hold mode F.
Select heating element On/Off A/B/C.
Adjust height of the hood to desired position.
Cook cycle time required 0-20mins I.
Hold setting will be the same as last used. (Adjust if necessary before start or during hold)
Start the unit Gor activate the plate detection.
(The LED will flash when cook or hold is in start)
Note: At cook cycle end the buzzer will sound, the unit will automatically start the
hold mode.
The power configuration, time and hold mode settings can be adjusted anytime
during operation. The unit will always remember the last settings used. When
cooking is ended “End” is displayed.
After 60sec of inactivity the display will show OPUS 800. Input on the keyboard or
encoder the display turns to normal state.
Shutting down
Turn the control knob to the ‘Off’ position and switch off at the isolating socket.
Be aware that the appliance will remain hot for some time.
CLEANING
Your Lincat product has a manufacturer’s warranty. This requires you to maintain
and care for your product and follow maintenance instructions. If you fail to maintain
your unit or damage components Lincat may charge you for a warranty repair.
Please check the website for terms and conditions.
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive materials
or cleaners containing chlorine. Dry with a soft cloth.

IS 609 ECN 3977 Page 8 of 9
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
Heat sink overheat
If the over temperature is reached the heating is disabled and a blinking label “Hot”
is displayed. The alarm is automatically reset when the temp falls below 5˚C below
this level.
Probe Failure
There is a label “St1” blinking if:
Temperature measured from ST1 is out of range.
Short circuit is recognized on analog input ST1
Open circuit is recognized on analog input ST1
Please inform the Lincat service desk when you call.
Part Number
Description
EL309
Element
EN02
Encoder
FI43
Noise Filter
FU25
Fuse
GL658
Glass
KN251
Control knob
PR01
PCBA Salamander
PR02
TRIAC Board
PR04
Electronic Cable PR02
SS11
Straps
SW100
Multi Function Switch
SW101
Multi Function Switch
TR03
Transformer
X52800
Micro switch
Part Number
Description
BR75
Wall bracket
FAULT FINDING
SPARE PARTS LIST
ACCESSORIES

IS 609 ECN 3977 Page 9 of 9
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Product code
All available on serial plate
Type number
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
SERVICE INFORMATION