Lincat Silverlink 600 ECG6 Owner's manual

IS 401 ECN 3607 Page 1 of 9
Installation, Operating and Servicing
Instructions
Silverlink 600 Electric Chargrills
ECG6, ECG9, ECG9/WT
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

IS 401 ECN 3607 Page 2 of 9
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
3-5
Operating Instructions
5-7
Cleaning
7
Servicing, Maintenance and Component Replacement
7
Fault Finding
7
Spare Parts List
8
Service Information and Guarantee
9
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 401 ECN 3607 Page 3 of 9
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Model
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
ECG6
387
600
600
30
ECG9
387
900
600
45
ECG9/WT
387
900
600
45
CHECK LIST OF ENCLOSURES
Warranty Card
Instructions manual
Water level indicator
Drain tube
Element lifting hook (ECG9, ECG9/WT)
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.

IS 401 ECN 3607 Page 4 of 9
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of this appliance.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of 60 Deg C.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed.
Fig 1

IS 401 ECN 3607 Page 5 of 9
Position this appliance under a fume extraction unit.
Power Ratings
Model
kW
Current (A)
ECG6
8.0
1N~+E 36.0 3N~+E L1 12 L2 12 L3 12
ECG9
13.3
L1 23.2 L2 23.2 L3 11.6
ECG9WT
13.3
L1 23.2 L2 23.2 L3 11.6
Connection to an appropriate electrical supply is via the cable inlet in the rear panel,
and must be made by a suitably qualified person.
Connection to a mains water supply is via the bulkhead coupling in the rear panel.
The valve has a working capacity of 0-16 bar (0kPa-1,600kPa).
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
To clean the appliance before first use, lift off the cooking grids (Fig 2) ensuring
they are not dragged across the element. Remove the splashguard and then lift
and swing the element into the upright position (A) until the element stay engages
(B). Clean the tank.
To return the element, pushing the element slightly back, manually disengage and
pull forward the stay. Lower the element into the tank and replace splashguard and
cooking grids.

IS 401 ECN 3607 Page 6 of 9
Fig 2
Place the octagonal water level indicator onto one of the element cross supports in
a visible position.
Ensure the drain valve is closed and add water either by the funnel at the rear left
hand corner or via the mains supply control valve on the control panel (ECG9WT).
Switch on the power supply - the green neon illuminates to indicate power to the
appliance. Set the control knobs to the required position.
Allow 15 minutes for the chargrill to warm up.

IS 401 ECN 3607 Page 7 of 9
Do not allow the water level to fall below minimum, as this will result in the
inconvenience of the safety thermostat operating, cutting off the power supply to the
appliance. The thermostat may only be reset when the appliance has cooled by
pressing the red button located in the rear panel. (For ECG9/WT the reset buttons
are locate on the control panel.)
If the appliance is not to be used for some time, lightly coating the grids with
cooking oil will help protect them.
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Allow the water temperature to cool. Fit the drain tube to the valve and drain the
water into a suitable container. Remove the splashguard and cooking grids and
raise the element from the tank as detailed in Operating Instructions.
Clean all panels with warm water and mild detergent, do not use abrasive
materials. Dry with a soft cloth. Lower element, refit splashguard and cooking
grids. Refill with fresh water.
Deposits on the cooking grids may be cleaned off with a wire brush.
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All servicing, maintenance and component replacement on these appliances should
be carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual
FAULT FINDING

IS 401 ECN 3607 Page 8 of 9
Part Number
Description
Used on
BP22
Branding plate
All
CO148
Connecting block
ECG9, ECG9/WT
CO215
Contactor
All
EL270
Element 8kW
All
EL276
Element 5.3kW
ECG9, ECG9/WT
EN10
Energy regulator
All
FE37
Foot
All
GA57
Element gasket
All
KN263
Control knob
All
LI42
Branding plate lifter
ECG9, ECG9/WT
NE42
Amber neon
ECG9/WT
NE43
Green neon
All
SG02
Sleeved grommet
All
SW64
Microswitch
All
TE45
Terminal block
All
TH73
Thermostat
All
WS02
Wire stay
All
SPARE PARTS LIST

IS 401 ECN 3607 Page 9 of 9
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Product code
All available on serial plate
Type number
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
SERVICE INFORMATION