Linear AM-CRI Operation and maintenance manual

AM-CRI
Card
Reader
Interface
Installation Instructions
INTRODUCTION
The AM-CRI card reader interface is designed for use with Linear’s
AE1000Plus, AE2000Plus, and AM3Plus access control systems. The
interface will support one or two 26-bit Weigand input devices.
If the readers used have a “hold” or “buffer” connection, two readers may
be used to the AM-CRI. If the readers do not have a “hold” or “buffer”
connection, one reader may be used with the AM-CRI.
Usually mounted near the readers, the AM-CRI interface connects to the
controller through a six-wire cable. Each reader connects to the AM-CRI
through a six-wire (one LED in reader) or seven wire (two LEDs in reader)
cable.
Two rotary switches in the AM-CRI select the PBUS device address for each
reader connected. Each remote PBUS device connected to the controller
must be set to a different device address. The address switches in the
AM-CRI must be set to different addresses if two readers are used.
Power is supplied to the interface and reader(s) from the controller. A power
selection jumper is provided for each reader. Five or eight volt power or
external power for locally powered readers can be selected.
1. TYPICAL INSTALLATION
2. OPEN CASE 3. LOCATE COMPONENTS 4. MOUNT READERS
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.linearcorp.com
CABLE RUN CABLE TYPE
FORMULA
120 FEET MAXIMUM BELDEN 9931 (24 AWG)
WEICO 9405 (20 AWG)
FEET x LOAD UNITS < 3,000 MAXIMUM
FEET x LOAD UNITS < 10,000 MAXIMUM
400 FEET MAXIMUM
CABLE TO
CONTROLLER
(SEE FORMULA)
HOMERUN
WIRE EACH
AM-CRI TO THE
CONTROLLER
ONE OR TWO READERS
CAN BE USED
AM-CRI
INTERFACE
(INSIDE WALL)
EACH AM-CRI EQUALS 25 LOAD UNITS
CABLE LENGTH FORMULA FOR EACH AM-CRI USED IN SYSTEM
SQUEEZE
SIDES
TOGETHER
SEPARATE
CASE
POWER & DATA
TERMINALS
(CONNECTS TO
CONTROLLER)
READER "A"
TERMINALS
READER "B"
TERMINALS
READER "A"
POWER JUMPER
READER "B"
POWER JUMPER
READER "A"
DEVICE ADDRESS
SELECTOR
READER "B"
DEVICE ADDRESS
SELECTOR
MOUNT READER(S)
PER MANUFACTURER'S
SPECIFICATIONS
PRINTER’S INSTRUCTIONS:
INSTR, INSTL, AM-CRI - LINEAR P/N: 211845 E - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2

Copyright © 2012 Linear LLC 211845 E
5. CONNECT READERS TO AM-CRI 6. SET DEVICE ADDRESS AND POWER JUMPERS 7. CONNECT AM-CRI TO CONTROLLER
DAT1
DAT0
LED2
LED1
HOLD
GND
PWR DAT1
DAT0
LED2
LED1
HOLD
GND
PWR
READER "A"
TERMINALS
READER "B"
TERMINALS
READER "A" READER "B"
REFER TO READER MANUFACTURER'S SPECIFICATIONS
FOR READER WIRE COLOR AND HOOK UP DETAILS
DAT1
DAT0
LED2
LED1
HOLD
GND
PWR
READER "B"
TERMINALS
READER "B"
SINGLE
READER
HOOKUP
W/O HOLD
TWO READER
HOOKUP
WITH HOLD
LED1- ON
DURING
STANDBY
LED2- ON
DURING
ACCESS
NOTE:
REFER TO STEP 3 ILLUSTRATION
FOR COMPONENT LOCATIONS
8 VOLT POWER
TO READER
5 VOLT POWER
TO READER
SET READER
POWER JUMPER
SET DEVICE
ADDRESS
SELECTOR
SET TO POSITION 1-6
(MUST BE DIFFERENT
FROM OTHER READER)
REMOVE JUMPER WHEN
USING EXTERNAL POWER
NOTE:
WHEN USING ONE READER WITHOUT A "HOLD" LINE,
CONNECT IT TO READER "B" TERMINALS AND SET
READER "A" DEVICE ADDRESS SELECTOR TO "0"
SET UNUSED READER
ADDRESS TO "0" AM-CRI
USE CABLE FORMULA
TO DETERMINE CABLE
TYPE AND MAXIMUM
LENGTH
NOTE: CONTROLLER MUST BE TURNED OFF BEFORE
MAKING ANY WIRING CONNECTIONS
AM-CRI
TERMINALS
PCLK
DVAL
DAT0
DAT1
GND
PWR
GND
DAT1
DAT0
DVAL
PCLK
PWR
ACCESS CONTROL
SYSTEM PBUS
TERMINALS
8. CLOSE CASE AND MOUNT UNIT 9. PROGRAM AND TEST LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and
workmanship for twelve (12) months. This warranty extends only to
wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as
to the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear LLC for consequential damages
arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property,
revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability
and implied warranties for fitness, are valid only until This Linear
LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details
USE FOUR SCREWS
TO MOUNT THE
AM-CRI
SNAP CASE TOGETHER
PROGRAM THE CONTROLLER
TO CONFIGURE THE PBUS
DEVICE
REFER TO THE CONTROLLER
PROGRAMMING INSTRUCTIONS
FOR DETAILS
PRINTER’S INSTRUCTIONS:
INSTR, INSTL, AM-CRI - LINEAR P/N: 211845 E - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 2 OF 2