Linksys PAP2 Guide

Model No.
PAP2 Ver. 2
with 2 Ports for Voice-over-IP
Phone Adapter
Installation and Troubleshooting Guide
Voice

Phone Adapter with 2 Ports for Voice-over-IP
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems,
Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights
reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
How to Use this Guide
Your guide to the Phone Adapter has been designed to make understanding networking with the Phone Adapter
easier than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section.
This exclamation point means there is a caution or warning and is
something that could damage your property or Phone Adapter.
This question mark provides you with a reminder about something you
might need to do while using the Phone Adapter.
This checkmark means there is a note of interest and is something you
should pay special attention to while using the Phone Adapter.
word: definition.
Figure 0-1: Sample Figure Description
PAP2_V2-UG-60421NC JL
WARNING: This product contains chemicals, including lead, known to the State of California to cause
cancer, and birth defects or other reproductive harm. Wash hands after handling.

Phone Adapter with 2 Ports for Voice-over-IP

Phone Adapter with 2 Ports for Voice-over-IP
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this Guide? 1
Chapter 2: Getting to Know the Phone Adapter 3
Back Panel Ports 3
The Front Panel 4
Chapter 3: Connecting the Phone Adapter 5
Overview 5
Instructions for Connecting the Phone Adapter 5
Placement Options 7
Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu 9
Overview 9
Accessing the Interactive Voice Response Menu 9
Using the Interactive Voice Response Menu 9
Configuring the Settings for Your Vonage Phone Service 14
Chapter 5: Using the Phone Adapter’s Web-based Utility 15
Overview 15
How to Access the Web-based Utility 16
The Setup Tab 17
The Administration Tab - Management 19
The Administration Tab - Log 21
The Administration Tab - Factory Defaults 22
The Status Tab 23
The Voice Tab 25
Appendix A: Troubleshooting 27
Common Problems and Solutions 27
Frequently Asked Questions 37

Phone Adapter with 2 Ports for Voice-over-IP
Appendix B: Windows Help 39
Appendix C: Glossary 41
Appendix D: Specifications 45
Appendix E: Warranty Information 47
Appendix F: Regulatory Information 49
Appendix G: Contact Information 65
Vonage 65
Linksys 65

Phone Adapter with 2 Ports for Voice-over-IP
List of Figures
Figure 2-1: Back Panel 3
Figure 2-2: Front Panel 4
Figure 3-1: Connect the Phone Adapter to Your Network and Telephone 5
Figure 3-2: Connect the Ethernet Network Cable 6
Figure 3-3: Connect the Power 6
Figure 3-4: Connect the Telephone Cable 6
Figure 3-5: Attaching the Phone Adapter’s Base 7
Figure 3-6: Phone Adapter Standing on Base 7
Figure 3-7: Measurement between Wall-Mount Slots 8
Figure 5-1: Login 16
Figure 5-2: Setup Tab - Obtain an IP automatically 17
Figure 5-3: Setup Tab - Static IP 17
Figure 5-4: Administration Tab - Management 19
Figure 5-5: Administration Tab - Log 21
Figure 5-6: Administration Tab - Factory Defaults 22
Figure 5-7: Status Tab 23
Figure 5-8: Voice Tab 25

Phone Adapter with 2 Ports for Voice-over-IP

Phone Adapter with 2 Ports for Voice-over-IP
1
Chapter 1: Introduction
Welcome
Chapter 1: Introduction
Welcome
Thank you for choosing the Linksys Phone Adapter with 2 Ports for Voice-over-IP. This Phone Adapter will allow
you to make phone or fax calls using the your broadband connection.
How does the Phone Adapter do this? The Phone Adapter connects your phones or fax machines to your
network router or gateway, so telephone service is delivered through your cable or DSL Internet connection.
Each of the Phone Adapter’s two telephone jacks operates independently, with separate phone service and
phone numbers, so you can have up to two Vonage phone lines per Adapter. You will be able to make phone
calls using the account you set up with Vonage, even while you’re surfing the Internet.
Use the instructions in the Quick Installation or this Installation and Troubleshooting Guide to help you connect
the Phone Adapter after you have set up an account with Vonage. These instructions should be all you need to
get the most out of the Phone Adapter.
What’s in this Guide?
This guide covers the steps for installing the Phone Adapter.
• Chapter 1: Introduction
This chapter describes the Phone Adapter’s applications and this Installation and Troubleshooting Guide.
• Chapter 2: Getting to Know the Phone Adapter
This chapter describes the physical features of the Phone Adapter.
NOTE: For information about
your Vonage phone service,
refer to the User Guide, which is
included in the welcome kit.

Phone Adapter with 2 Ports for Voice-over-IP
2Chapter 1: Introduction
What’s in this Guide?
• Chapter 3: Connecting the Phone Adapter
This chapter explains how to connect the Phone Adapter to your network and phones (or fax machines).
• Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu
This chapter explains how to configure the Phone Adapter’s network settings.
• Chapter 5: Using the Phone Adapter’s Web-based Utility
This chapter explains how to configure the Phone Adapter using your web browser and its Web-based Utility.
• Appendix A: Troubleshooting
This appendix describes some potential problems and solutions, as well as frequently asked questions,
regarding use of the Phone Adapter.
• Appendix B: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as
installing the TCP/IP protocol.
• Appendix C: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix D: Specifications
This appendix provides the technical specifications for the Phone Adapter.
• Appendix E: Warranty Information
This appendix supplies the warranty information for the Phone Adapter.
• Appendix F: Regulatory Information
This appendix supplies the regulatory information regarding the Phone Adapter.
• Appendix G: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support,
as well as Vonage.

Phone Adapter with 2 Ports for Voice-over-IP
3
Chapter 2: Getting to Know the Phone Adapter
Back Panel Ports
Chapter 2: Getting to Know the Phone Adapter
Back Panel Ports
The Phone Adapter’s ports are located on the back panel.
Reset Button There are two ways to reset the Phone Adapter's factory defaults. Either press the Reset
Button for 30 seconds, or restore the defaults from the Web-based Utility.
PHONE 1/2 Port The PHONE 1/2 port allows you to connect your telephone or fax machine to the Phone
Adapter using an RJ-11 telephone cable (not included). Use the PHONE 1 port for the
primary Vonage line, and use the PHONE 2 port if you have a second Vonage line.
INTERNET Port The INTERNET port allows you to connect the Phone Adapter to your router or gateway
using a Category 5 (or better) Ethernet network cable.
Power Port The Power port is where you will connect the included power adapter.
Figure 2-1: Back Panel
NOTE: These Phone ports do
not carry any voltage.
IMPORTANT: Use only the
included power adapter to
power the Phone Adapter. If you
use a different power adapter,
the Phone Adapter may be
damaged or may not work.

Phone Adapter with 2 Ports for Voice-over-IP
4Chapter 2: Getting to Know the Phone Adapter
The Front Panel
The Front Panel
The Phone Adapter’s LEDs are located on the front panel.
PHONE 1/2 LED Green. The PHONE 1 LED is solidly lit when a telephone or fax machine has a registered
connection to Vonage through the corresponding port. (The connection is registered if your
Vonage phone service account is active.) It flashes when the phone is being used or an
incoming call has been detected.
INTERNET LED Green. The INTERNET LED lights up when the Phone Adapter is connected to your network
through the Internet port. It flashes when there is data being sent or received.
Power LED Green/Red. The power LED lights up when the Phone Adapter is powered on and ready. It
flashes green when the Phone Adapter is booting up, undergoing a self-test, or performing
a firmware upgrade. The LED lights up red when the Phone Adapter has failed its self-test
or is malfunctioning. Refer to “Appendix A: Troubleshooting” for more information.
Figure 2-2: Front Panel
IMPORTANT: The PHONE and
power LEDs must be solid
green to make phone calls.

Phone Adapter with 2 Ports for Voice-over-IP
5
Chapter 3: Connecting the Phone Adapter
Overview
Chapter 3: Connecting the Phone Adapter
Overview
This chapter gives instructions on how to connect the Phone Adapter to your network and telephones or fax
machines. Shown below is a connection diagram displaying a typical setup.
This chapter also describes the Phone Adapter’s placement options. You can place it flat on a surface, attach
the Phone Adapter’s base so it can stand in place, or mount the Phone Adapter on a wall.
Instructions for Connecting the Phone Adapter
If you already have an account set up with Vonage, then proceed to step 1.
If you do not have an account, visit www.vonage.com to activate the Phone Adapter. After you have set up an
account, then proceed to step 1.
Figure 3-1: Connect the Phone Adapter to Your Network and Telephone
IMPORTANT: The Phone
Adapter includes a ringer (ring
signal generator), which is a
source of hazardous voltage.
When the ringer is activated by
an incoming call, do not touch
the Phone port wires, the wires
of a cable connected to either
of the Phone ports, or the
internal circuitry of the Phone
Adapter.
Telephone
Router
Cable/DSL
Modem
Internet Phone Adapter
IMPORTANT: Do not connect
either of the Phone ports to a
telephone wall jack. Make sure
you only connect a telephone or
fax machine to either of the
Phone ports. Otherwise, the
Phone Adapter or the telephone
wiring in your home or office
may be damaged.

Phone Adapter with 2 Ports for Voice-over-IP
6Chapter 3: Connecting the Phone Adapter
Instructions for Connecting the Phone Adapter
1. Connect the included Ethernet network cable to the INTERNET port of the Phone Adapter.
Connect the other end to the one of the Ethernet ports on your router or gateway.
2. Connect the included power adapter to the Power port on the back panel of the Phone Adapter.
Connect the other end to a standard electrical outlet.
3. Using a telephone cable, connect your telephone to the PHONE 1 port of the Phone Adapter.
4. If you have a second Vonage line on your account, then connect another telephone or a fax machine to the
PHONE 2 port of the Phone Adapter.
5. The power, INTERNET, and PHONE LEDs will be solidly lit when the Phone Adapter is ready for use. Pick up
a telephone and check for a dial tone.
6. Follow the instructions provided by Vonage.
If you need to manually configure the Phone Adapter’s network settings, you can use the telephone; for
instructions, proceed to “Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu.”
The installation of the Phone Adapter is complete. Now you can pick up your phone and make calls.
Proceed to the next section, “Placement Options,” if you want to attach the Phone Adapter’s base.
Figure 3-3: Connect the Power
Figure 3-4: Connect the Telephone Cable
Figure 3-2: Connect the Ethernet
Network Cable
NOTE: Vonage supports 7-, 10-, and 11-digit dialing. Use 7-, 10-, or 11-digit dialing for calls
within the same area code as your Vonage phone number. Use 10- or 11-digit dialing for calls
outside of your area code.

Phone Adapter with 2 Ports for Voice-over-IP
7
Chapter 3: Connecting the Phone Adapter
Placement Options
Placement Options
There are two ways to place the Phone Adapter. The first way is to place the Phone Adapter horizontally on a
surface. The second way is to stand the Phone Adapter vertically on a surface. The third way is to mount the
Phone Adapter on a wall. The second and third options are explained in further detail below.
Stand Option
1. Remove the plate from the Phone Adapter’s bottom panel.
2. Line up the pegs of the Phone Adapter’s base with the mounting holes of the Phone Adapter’s bottom panel.
3. Insert the Phone Adapter’s base into the Phone Adapter’s bottom panel. Push the base in until it fits snugly.
4. Place the Phone Adapter in an appropriate location.
Congratulations! The installation of the Phone Adapter is complete.
If you need to change any of the Phone Adapter’s network settings, proceed to “Chapter 4: Using the
Phone Adapter’s Interactive Voice Response Menu.”
Figure 3-5: Attaching the Phone
Adapter’s Base
Figure 3-6: Phone Adapter Standing
on Base

Phone Adapter with 2 Ports for Voice-over-IP
8Chapter 3: Connecting the Phone Adapter
Placement Options
Wall-Mount Option
The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm
(2.28 inches).
1. Determine where you want to mount the Phone Adapter.
2. Drill two holes into the wall. Make sure the holes are 58 mm (2.28 inches) apart.
3. Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.
4. Maneuver the Phone Adapter so the wall-mount slots line up with the two screws.
5. Place the wall-mount slots over the screws and slide the Phone Adapter down until the screws fit snugly into
the wall-mount slots.
Congratulations! The installation of the Phone Adapter is complete.
If you need to change any of the Phone Adapter’s network settings, proceed to “Chapter 4: Using the
Phone Adapter’s Interactive Voice Response Menu.”
Figure 3-7: Measurement between
Wall-Mount Slots

Phone Adapter with 2 Ports for Voice-over-IP
9
Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu
Overview
Chapter 4: Using the Phone Adapter’s Interactive Voice
Response Menu
Overview
Chapter 4 explains how you can use the Interactive Voice Response Menu to configure the Phone Adapter’s
network settings. You may need to change these settings depending on the specifics of your local network
setup. Use the phone’s keypad to enter your commands and select choices, and the Phone Adapter will respond
with voice responses.
Accessing the Interactive Voice Response Menu
1. Use a telephone connected to the PHONE 1 or PHONE 2 port of the Phone Adapter.
2. Press **** (in other words, press the star key four times).
3. You will hear, “Configuration menu. Please enter option followed by the # (pound) key or hang up to exit.”
Refer to the following table that lists actions, commands, menu choices, and descriptions. After you select
an option, press the #(pound) key. To exit the menu, hang up the telephone.
Using the Interactive Voice Response Menu
While entering a value, such as an IP address, you may exit without entering any changes. Press the * (star) key
twice within half a second. Otherwise, the * will be treated as a decimal point or dot.
NOTE: If you need to change
the settings for your Vonage
Internet phone service, then
visit www.vonage.com to
access your online account.

Phone Adapter with 2 Ports for Voice-over-IP
10 Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu
Using the Interactive Voice Response Menu
After entering a value, such as an IP address, press the # (pound) key to indicate you have finished your
selection. To save the new setting, press 1. To review the new setting, press 2. To re-enter the new setting, press
3. To cancel your entry and return to the main menu, press *(star).
For example, to enter the IP address 191.168.1.105 by keypad, press these keys: 191*168*1*105. Press the #
(pound) key to indicate that you have finished entering the IP address, and then press 1to save the IP address.
To cancel your entry and return to the main menu, press *(star).
If the menu is inactive for more than one minute, the Phone Adapter will time out. You will need to re-enter the
menu by pressing ****.
The settings you have saved will take effect after you have hung up the telephone. The Phone Adapter may
reboot at this time.
Interactive Voice Response Menu
Action Command
(press these
keys on the
telephone)
Choices Description
Enter Interactive Voice
Response Menu
**** Use this command to enter the
Interactive Voice Response Menu. Do
not press any other keys until you
hear, “Configuration menu. Please
enter option followed by the # (pound)
key or hang up to exit.”

Phone Adapter with 2 Ports for Voice-over-IP
11
Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu
Using the Interactive Voice Response Menu
Check DHCP 100 Use this command to find out if DHCP
has been enabled or disabled. If
enabled, the Phone Adapter will be
automatically assigned an IP address
by your network router or gateway. If
disabled, then the Phone Adapter will
use a static IP address.
Enable/Disable DHCP 101 Enter 1to enable
Enter 0to disable
Enable or disable the Phone Adapter’s
DHCP feature. If your network router
or gateway assigns IP addresses, then
enter 1. Otherwise, enter 0.
Check IP Address 110 You will hear the current IP address of
the Phone Adapter.
Interactive Voice Response Menu
Action Command
(press these
keys on the
telephone)
Choices Description

Phone Adapter with 2 Ports for Voice-over-IP
12 Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu
Using the Interactive Voice Response Menu
Set Static IP Address 111 Enter the IP
address using
numbers on the
telephone keypad.
Use the * (star) key
when entering a
decimal point.
To set a static IP address, the DHCP
feature must be disabled. If the DHCP
feature is enabled, then you will hear,
“Invalid Option,” if you try to set a
static IP address.
Check Network Mask
(or Subnet Mask)
120 You will hear the current network
mask of the Phone Adapter.
Set Network Mask (or
Subnet Mask)
121 Enter the network
mask using
numbers on the
telephone keypad.
Use the * (star) key
when entering a
decimal point.
To set the network mask, the DHCP
feature must be disabled. If the DHCP
feature is enabled, then you will hear,
“Invalid Option,” if you try to set the
network mask.
Check Static Gateway
IP Address
130 You will hear the current gateway IP
address of the Phone Adapter.
Interactive Voice Response Menu
Action Command
(press these
keys on the
telephone)
Choices Description