Linksys AC 1200 Max User manual

RE6500
User Guide

1
Linksys AC1200 Max Wi-Fi Range Extender
Introduction
This User Guide can help you connect the extender to your network and solve
common setup issues. You can find more help from our award-winning, 24/7
customer support at Linksys.com/support.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to install the range extender ................ 2
How to access the browser-based utility ...........3
Using Wi-Fi Protected Setup ..................... 4
How to use Site Survey .......................... 6
Cross-Band ...................................... 7
Wireless Music Playback.......................... 7
Troubleshooting ................................. 7
Specifications ................................... 9
Overview
Front
The light on the front of the range extender gives you information about power
andWi-Fi Protected Setup. UseWi-Fi Protected Setup to automatically and securely
connect client devices such as wireless printers that support Wi-Fi Protected
Setup. Note: Your antennas might look different from those pictured here.
Power Light Status/ description
Blinking white When the extender is powered on,
is resetting to factory defaults, or
upgrading its firmware
Solid white When the extender is ready to use
Blinking amber for two minutes When the extender cannot establish a
connection or encounters a problem
Fix: Unplug the power from the
extender, plug it back in, wait two
seconds, and then reconnect it to
your network
Power Light

2
Linksys AC1200 Max Wi-Fi Range Extender
Audio Jack Ethernet Power
Wi-Fi Protected
Setup™button
Back
Power Switch European versions only.
Wi-Fi Protected Setup Button Use Wi-Fi Protected Setup to automatically and
securely add wireless devices to your network. Refer to Using Wi-Fi Protected
Setup on page 7.
Ethernet (blue) Connect wired devices to your wireless network with
Ethernet (network) cables. The green light turns on when an Ethernet device
is connected and active on this port. The light blinks when the extender is
sending or receiving data over the Ethernet port.
Audio Port Connect the extender to your speaker.
Bottom
Reset Press and hold this button for about five seconds to reset the extender to
its factory defaults. You can also restore the defaults from the Administration >
Factory Defaults screen in the extender’s browser- based utility.
How to install the range extender
Before setup, unplug or disconnect any range extenders on the network.
1. Connect the antennas and power cable as pictured. Antennas should be
upright for best results. Note: Your antennas might look different from those
pictured here.
2. Plug in the range extender midway between your router and the area
without Wi-Fi. Be sure you have at least 50% of your router’s Wi-Fi signal at
that point on the device you will use for setup.
3. Wait for a solid light on the cover of the range extender. It could take up to
two minutes. On a computer, phone or tablet, connect to the Wi-Fi network
“Linksys Extender Setup.”
• Windows 7 and Windows 8 will ask you, “Do you want to set up your
network?” Click the link, “Connect to network without setting it up.”
4. If setup doesn’t start automatically, open a browser to http://192.168.1.1.
TIP
You can also connect the range extender by using Wi-Fi Protected Setup. For
more information, see“Using Wi-Fi Protected Setup”on page 7.
1.5A
12VDC
1.5A
12VDC
Range Extender
Reset button

3
Linksys AC1200 Max Wi-Fi Range Extender
How to access the browser-based utility
After setting up the extender use the extender’s browser-based utility to
change any settings.
Windows XP:
TIP
To follow these instructions, UPnP needs to be enabled in
Windows XP. To enable UPnP:
1. Click Start, Control Panel, Add or Remove Program, then click Add/
Remove Windows Components.
2. Select Network Services, then click Details.
3. Select UPnP User Interface, then click OK
1. Open Windows Explorer. Click My Network Places on the left panel.
2. Look for the RE6500 icon on the right panel. (You might be required to
change the firewall settings to allow the display of networked computers.
Refer to your operating system’s help for instructions.)
3. Double-click the RE6500 icon. A web browser will open and prompt you
to enter your User name and Password.
4. Leave the User name field blank, and enter the default password “admin.”
5. Click OK.
Windows 8, Windows 7, or Vista:
1. Open Windows Explorer (File Explorer in Windows 8). Click Network. Look
for the RE6500 icon on the right panel. (You might be required to change
the firewall settings to allow the display of networked computers. Refer to
your operating system’s help for instructions.)
2. Right-click the RE6500 icon. Click Properties. Click on the address link in
Device webpage. A web browser will open and prompt you to enter a
User name and Password.
3. Leave the User name blank, and enter the default password “admin.”
4. Click OK.
Mac OS X
1. Open Safari. Click the book icon. Click Bonjour on the left panel. Look for
the RE6500 icon on the bottom right panel.
2. Double-click the RE6500 icon.
3. Leave the User name blank, and enter the default password “admin.”
4. Click OK.
Changes to settings will not be effective until you click Save Settings at the
bottom of the screen. You also can click Cancel Changes to clear any changes.
Click Help on the right side of the screen for additional information on the
screen’s options.

4
Linksys AC1200 Max Wi-Fi Range Extender
Using Wi-Fi Protected Setup
Wi-Fi Protected Setup™ makes it easy to connect your extender to your network,
and connect other devices to your network through the extender.
Wi-Fi Protected Setup light activity
WPS Light Status/ description
Blinking white When WPS connection is in process
Solid white When WPS connection is successful
Blinking amber for two minutes When WPS cannot establish connection
or encounters a problem
Fix: wait a few seconds after LED stops
blinking and try again
Connecting the extender to an existing access point
If your access point or router supports it, you can use Wi-Fi Protected Setup
to connect the range extender to the access point or router. Choose from the
setup methods below to connect the extender.
NOTE
If you have an access point or a router that does not support Wi-Fi Protected
Setup, note the wireless settings, and then manually configure the extender.
Connecting with the Wi-Fi Protected Setup Button
Use this method if your router or access point has a Wi-Fi Protected Setup button.
1. Press the Wi-Fi Protected Setup button on the extender.
2. Click the Wi-Fi Protected Setup button on the router’s Wi-Fi Protected
Setup screen (if available), OR press and hold the Wi-Fi Protected Setup
button on the router for one second. When the connection is complete,
the Wi-Fi Protected Setup light on the extender will be solid.
3. If you used the extender’s Wi-Fi Protected Setup screen, click OK in that
screen within two minutes.

5
Linksys AC1200 Max Wi-Fi Range Extender
NOTE
If you have a dual-band router and wish to connect to both bands, you will
have to perform the WPS setup twice. The first connection will be on the 2.4
GHz band.
Connecting with the range extender’s PIN
The Wi-Fi Protected Setup PIN (Personal Identification Number) can be found
on the product label on the bottom of the extender. You can use this method
only if your router’s administration utility has a Wi-Fi Protected Setup menu.
1. Enter the extender’s PIN into the appropriate field on the router’s Wi- Fi
Protected Setup screen. Click Register. When the connection is complete,
the Wi-Fi Protected Setup light on the extender will be solid.
2. Click OK.
Connecting devices to your network through the
extender
Choose from the methods below to connect devices that support Wi-Fi
Protected Setup to your network.
NOTE
Repeat the instructions for each client device that supports Wi-Fi Protected
Setup.
Connecting with the Wi-Fi Protected Setup Button
Use this method if your client device has a Wi-Fi Protected Setup button.
1. Press the Wi-Fi Protected Setup button on the client device.
2. Click the Wi-Fi Protected Setup button on the extender’s Wi-Fi Protected
Setup screen, OR press and hold the Wi-Fi Protected Setup button on
the top panel of the extender for one second. When the connection is
complete, the Wi-Fi Protected Setup light on the extender will be solid.
3. If using the extender’s Wi-Fi Protected Setup screen, be sure to click OK
within two minutes or you will have to start over.
Connecting with the client device’s PIN
Use this method if your client device has a Wi-Fi Protected Setup PIN (Personal
Identification Number).
1. Enter the PIN from the client device in the field on the extender’s Wi-Fi
Protected Setup screen.
2. Click Register on the extender’s Wi-Fi Protected Setup screen. When the
connection is complete, the Wi-Fi Protected Setup light on the extender
will be solid.
3. Click OK on the extender’s Wi-Fi Protected Setup screen within two minutes
or you will have to start over.

6
Linksys AC1200 Max Wi-Fi Range Extender
Connecting with the extender’s PIN
Use this method if your client device asks for the extender’s PIN.
1. On the client device, enter the PIN listed on the extender’s Wi-Fi Protected
Setup screen. (It is also listed on the product label on the bottom of the
extender.) When the connection is complete, the Wi-Fi Protected Setup
light on the extender will be solid.
2. Click OK on the extender’s Wi-Fi Protected Setup screen within two
minutes.
How to use Site Survey
Site Survey gives a snapshot of all neighboring access points and wireless
routers within range of the extender.
To open the Site Survey page:
1. Log in to the browser-based utility (see “How to access the browser- based
utility”on page 5).
2. Click the Wireless tab. Click the Site Survey page.
3. Select—To connect to a wireless network, click the button next to the
wireless network name (SSID) in the Select column, and click Connect.
4. SSID—Displays the name of neighboring wireless networks.
5. GHz—Displays the radio band (in GHz) of the neighboring wireless
networks
6. Signal Strength—Displays the relative position of the neighboring
access points by indicating the power of the wireless signal received: 1
bar= 20%,2 bars=40%, 3 bars=60%, 4 bars=80%, 5 bars=100%. If no bar is
displayed, the extender is located too far away from the upstream access
point. Try to keep the signal strength between 60% and 100% for optimum
performance.
7. Security—Displays the mode of security in use by the neighboring APs. If
a network supports Wi-Fi Protected Setup, the Wi-Fi Protected Setup icon
is also displayed.
To connect your extender with an access point or router in Site Survey, you
will need to know the password or passphrase of the network on that device.
1. Select the network name (SSID) that you want to repeat with your extender
by clicking the corresponding button in the Select column.
2. Click Connect. When prompted, enter the password or passphrase used to
secure your wireless network. The type of security information required in
this screen must match your access point or router’s wireless security settings.
3. Click Save Settings. Your extender wireless parameters should be
configured. The wireless interface will restart, and the extender will
connect to the access point or router you have chosen.

7
Linksys AC1200 Max Wi-Fi Range Extender
Cross-Band
Cross-Band is the simultaneous use of both bands for high-speed data transfer
and uninterrupted streaming and gaming.
Wireless Music Playback
The extender allows you to stream music on your network and play on on
speakers through the audio port. This list of supported media players is subject
to change with the release of new software or mobile apps.
• Windows users can stream music with Windows Media Player12.
• Mac users can stream music with proprietary software or the SofaPlay app.
• Android users can stream music with MediaHouse, UPnPlay, Skifta, ArkMC,
BubbleUPnP, Pixel Media, and 2Player 2.0.
• iOS devices including iPhone, iPad or iPod can stream music with
proprietary software or other apps such as ArkMC, Smartstor Fusion,
Mconnect, and DK UPnP/DLNA.
• The extender supports MP3, FLAC, WAV, WMA and AAC file formats, as long
as those formats are supported by the device and app doing the streaming.
• The 3.5mm stereo port supports earphones and powered speakers.
Troubleshooting
NOTE
Your RE6500 works on 2.4GHz and 5GHz networks.
You cannot get your extender connected
Check the position of your router and extender
• For first-time setup, you may need to place the extender closer to the
router. After you’ve set up your extender, you can unplug it and move it to
the final location.
• To reduce signal obstructions, try alternate locations for the router and
extender.
• Avoid placing the router and extender near metal objects, masonry walls,
and reflective surfaces such as glass or mirrors.
• Avoid placing the router and extender near other electronics that may
cause signal interference.
If you’re using Wi-Fi Protected Setup to connect
• Wait until the Wi-Fi Protected Setup indicator stops blinking before trying
to make the connection again.
You cannot access your range extender
To access your range extender, you must be connected to your own network. If
you currently have wireless Internet access, the problem may be that you have
accidentally connected to a different wireless network.
For Mac instructions, see“To fix the problem on Mac computers:” on page 8.
To fix the problem on Windows computers:
1. On your Windows desktop, right-click the wireless icon in the system tray.
The icon might look different depending on which version of Windows you
are running.

8
Linksys AC1200 Max Wi-Fi Range Extender
2. Click View Available Wireless Networks.
3. Select your network name. Click Connect. In the example below, the
computer was connected to another wireless network named JimsRouter.
The name of the correct network, BronzeEagle in this example, is selected.
4. If you are prompted to enter a network key, type your password (Security
Key) into the Network key and Confirm network key fields. Click Connect.
You should now be able to access the range extender’s browser-based utility.
To fix the problem on Mac computers:
1. In the menu bar across the top of the screen, click the Wi-Fi icon. Linksys
Connect has automatically assigned your network a name.
In the example below, the computer was connected to another wireless network
named JimsRouter. The name of the Linksys E-Series network, BronzeEagle in
this example, is selected.
2. Select the wireless network name of the router you want to connect to.
3. Type your wireless network password (Security Key) into the Password
field. Click OK.
You have intermittent connection problems
Plug in the range extender midway between your router and the area without
Wi-Fi. Be sure you have at least 50% of your router’s Wi-Fi signal at that point on
the device you used for setup.

9
Linksys AC1200 Max Wi-Fi Range Extender
Specifications
RE6500
Model Name Linksys RE6500
Model Description Dual-band Wireless-AC Range Extender
Model Number RE6500
Standards IEEE 802.11ac, 802.11a, 802.11n, 802.11g, 802.11b, 802.3u
Ports Gigabit Ethernet, Audio, power
Buttons Reset, Wi-Fi Protected Setup™,
Power (European model only)
LEDs Power/Wi-Fi Protected Setup,
Ethernet (link, activity)
Cabling Type CAT 5e
Antennas 2 external
Detachable (y/n) Yes
Wireless Security Wi-Fi Protected Access™ 2 (WPA2),
Wi-Fi Protected Access™ (WPA), WEP
Security Key Bits Up to 128-bit encryption
Environmental
Dimensions 6.06” x 4.29” x 1.18” (154 x 109 x 30 mm)
Weight 5.57 oz (158 g)
Power 12VDC/1.0A
Certification FCC, ICES-003, RSS210, CE,
Wi-Fi (IEEE 802.11a/b/g/n/ac), WPA2™, WMM®,
Wi-Fi Protected Setup™
Operating Temperature 32 to 104°F (0 to 40°C) Storage Temperature
-4 to 140°F (-20 to 60°C) Operating Humidity
10 to 80% noncondensing Storage Humidity
5 to 90% noncondensing
Specifications are subject to change without notice.

Visit linksys.com/support for award-winning 24/7
technical support
BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin
group of companies. Third-party trademarks mentioned are the property of their
respective owners. Licenses and notices for third party software used in this product
may be viewed here: http://support.linksys.com/en-us/license. Please contact
http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code
requests. © 2014 Belkin Interntional, Inc. and/or its affiliates. All rights reserved.
LNKPG-00125 Rev. A01