LinTronic TT455-RT-238 User manual

BeoSystem control of non-B&O TV, screen or projector
BeoSystem control
of non-B&O TV, screen or projector
CINEMA MODE
IR-Tx IR-Tx IR-Rx IR-Tx
http://www.lintronic.dk
Updated: 190108
LinTronic

BeoSystem control of non-B&O TV, screen or projector
http://www.lintronic.dk
The TT455-RT-238 can be your gateway to
utilizing the potential of CINEMA control from
your BeoSystem.
When you press the CINEMA
(or FORMAT + 0 on some remotes) button on
your B&O remote, your BeoSystem can automate
control of a projector, projector screen, shades
and even lighting to give you the full cinematic
experience.
Lintronic provides solutions for relay controls,
but you can also use the TT455-RT-238 to
send out IR control of your devices when
using CINEMA mode.
All that you need are pinout/breakout boards
and a few wires to make the connections of
the pins between the breakout boards.”

BeoSystem control of non-B&O TV, screen or projector
http://www.lintronic.dk
LIGHT
T
C
DV
SA
VTAPE
RECORD
9
8
7
6
5
4
3
2
1
ME
TE
GO
EXIT
LIST
ST
>
>
BANG &
>
>
>
>>
TT-IR-8087030
TT455-RT-238
BeoSystem
IR DATA INPUT
RS232 EXTERNAL RECEIVER
UP TO 50 METERS
width:
7 cm
DIGITAL OUTPUT 2
Controlling the TT455-RT-238 and the BeoSystem
using only one IR receiver.

BeoSystem control of non-B&O TV, screen or projector
http://www.lintronic.dk
Controlling the TT455-RT-238 and the BeoSystem
using only one IR receiver.
In Memory Map:
Set the digital output 2 to Beosystem

BeoSystem control of non-B&O TV, screen or projector
Output Power Communication Input Output Power Communication Input Aux
5 4 3 2 1
9 8 7 6
Rx (from cpu)
Tx (to cpu)
Gnd
External receiver
To computer
TO BEOSYSTEM B
Ground
IR/DATA
B
C
Jack connector seen
from solderside
CB
DIGITAL OUTPUT 2
NOTE:
The digtal output 2
is as default set to
12 volt output.
Must be changed to
ground output.
See technical manual
how to solder for
5 volt pull-up.
Controlling the TT455-RT-238 and the BeoSystem
using only one IR receiver.
http://www.lintronic.dk

BeoSystem control of non-B&O TV, screen or projector
5 4 3 2 1
9 8 7 6
TO BEOSYSTEM B
Ground
IR/DATA
CB
DIGITAL OUTPUT 2
http://www.lintronic.dk
When the TT-IR-8087030 IR receiver is inserted into the IR INPUT
and DIGITAL OUTPUT 2 is set to BeoSystem, you should be able to
monitor the IR noise/signal from the IR receiver on the digital output 2
on an oscilloscope, as shown below.
Output Power Communication Input Output Power Communication Input Aux
External receiver

BeoSystem control of non-B&O TV, screen or projector
54321
9876
5 4 3 2 1
9 8 7 6
Tx
Rx
Gnd
Digital Inputs
Gnd
1
BeoSystem
3
Gnd
DigOut 1
DigOut 2
RS232
TV, screen, projector, light, etc.
The TT455-RT-238 may work together with a BeoSystem and convert the digital outputs into
infrared or RS232 commands for a non-B&O tv, screen, projector, light system, etc. etc.
The BeoSystems digital outputs are activated when the BeoSystem enters Cinema mode, and
they are de-activated when the BeoSystem leaves Cinema mode.
The TT455-RT-238 is easily configured to react when the digital input is activated or de-
activated, or both - and will send IR or RS232 commands as instructed.
Cinema Control
2
6
7
5
The TT455-RT-238 will trigger
on the digital signals and convert
into relays, infrared or RS232
commands.
http://www.lintronic.dk
BEOSYSTEM 3
See next pages for
Beosystem 4

BeoSystem control of non-B&O TV, screen or projector
5 4 3 2 1
9 8 7 6
This example shows how a BeoVision-7 controls a Sanyo projector (normally not supported by
the BV7) when the customer activates FORMAT-0 on his BEO4.
Cinema Control
54321
9876
DigOut 1
Gnd
54321
9876
DigIn1Tx1Gnd
Rx Gnd
TT455-RT-238 Signal Converter
- When Digital Output 1 from Beosystem is On,
then send Power On by RS232 to Sanyo.
- When Digital Output 1 from Beosystem is Off,
then send Power Off by RS232 to Sanyo.
Optionally RS232 port 2 could control your
light system ?
Or the digital outputs could control
a couple of relays ?
Tx2
Gnd
Tx2
RS232 for your light ?
Relays ?
http://www.lintronic.dk
BEOSYSTEM 3
See next pages for
Beosystem 4
BeoSystem
3

BeoSystem control of non-B&O TV, screen or projector
5 4 3 2 1
9 8 7 6
Tx
Rx
Gnd
Digital Inputs
Gnd
1
Gnd
Out1
Out 2
RS232
TV, screen, projector, light, etc.
The TT455-RT-238 may work together with a BeoSystem and convert the digital outputs into
infrared or RS232 commands for a non-B&O tv, screen, projector, light system, etc. etc.
The BeoSystems digital outputs are activated when the BeoSystem enters Cinema mode, and
they are de-activated when the BeoSystem leaves Cinema mode.
The TT455-RT-238 is easily configured to react when the digital input is activated or de-
activated, or both - and will send IR or RS232 commands as instructed.
PUC 1
2
2
3
4
The TT455-RT-238 will trigger
on the digital signals and convert
into relays, infrared or RS232
commands.
http://www.lintronic.dk
BEOSYSTEM 4
RJ45 breakout box
can be found on
Amazon or Ebay

2 4
BEOSYSTEM 4
PUC 1
RJ45 breakout box
can be found on
Amazon or Ebay

BeoSystem control of non-B&O TV, screen or projector
1 2 3
C A R C A R C A R C A R
C A R C A R C A R C A R
1 2 3 4
5 6 7 8
GND 12V G B A 2 1
COM1 COM2
BEOSYSTEM
Cinema mode On
When Digital Output 1 goes low (active), then relay 1 and relay 2 are activated (ON - no timeout).
Relay 3 is activated for the programmed time (default 3 seconds).
When Digital Output 2 goes low (active), then relay 5 and relay 6 are activated (ON - no timeout).
Relay 7 is activated for the programmed time (default 3 seconds).
When Digital Output 1 goes high (in-active), then relay 1 and relay 2 are de-activated (Off).
Relay 4 is activated for the programmed time (default 3 seconds).
When Digital Output 2 goes high (in-active), then relay 5 and relay 6 are de-activated (Off).
Relay 8 is activated for the programmed time (default 3 seconds).
Cinema mode Off
BEOLIVING
BeoSystem
6 7 5
GND
OUPUT 2 OUPUT 1
Quick-adjust the on-time for
relay 3, 4, 7, 8 (default 3 seconds):
- activate and hold switch 2
- count the seconds (blinks)
- Release switch 2
http://www.lintronic.dk

BeoSystem control of non-B&O TV, screen or projector
Output Comm Input Output
BeoSystem
1
1 2
5 6
IR RECEIVER
TT-IR-ET03
STEREO-EXT-10
5 1 4 2 3
5 6 7
5 2 3
9-pin SUB-D/Male
9-pin SUB-D/Female
9-pin SUB-D/Male
5 2
5 2 4 6 9-pin SUB-D/Female
TT455-RT-238 reacts to Cinema mode on/off, controls screen
up/down and projector by RS232 and 3’rd party products by IR.
9-pin SUB-D/Female
http://www.lintronic.dk