Lit Lightz INFINITY GLOW UNDERGLOW Series Configuration guide

2 x 60" Aluminum Innity Glow™ LED strip (Sides)
2 x 36" Aluminum Innity Glow™ LED strip (Front & Rear)
1 x 10 Extension cable (Rear only)
3 x Extension cable
10 x Aluminum mounng brackets
10 x screws
x
Self Tapping
Screws8 Self Tapping
6
ATTENTION
Please follow the guidelines
below before installing your
kit.
1. Before installing please connect all LED strips
to the 4 in your kit
aluminum
connector driver included
2. Once you have connected all strips. With an external
12V power source, connect the Red wire (power) and black
wire (ground) and fully test and make sure all aluminum
strips are working properly.
1. Make sure you properly clean the mounng area
with rubbing alcohol or non-residue degreaser.
2. Allow to air dry for and give a nal
wipe down with a clean microber.

You have 2 opons to mount the Innity Glow™ underglow
kit. These opons are general guidelines. Every car or truck
is dierent. Please make the necessary adjustments if needed.
- Start by measuring the mounng area. Once you have the area aligned, mount
the brackets with the small screws provided. You will use 2 brackets for the front
& rear and 3 brackets for each side.
- Once you have the brackets set, remove the 3M adhesive tape from the back of
the LED strip and start to mount it. Hold down the full LED strip for 90 seconds
so the 3M can aach to the surface.
- Make sure you wipe down the surface with degreaser,
let it air dry before applying the strip.
*Note* For the aluminum brackets to hold the aluminum strip, the
brackets will need to be clip to the 2-second row on the side of the
aluminum strip. You will hear it clip if you mounted them correctly.
Depending on the vehicle, you may or may not have a at surface on
the rear of the car. If this is the case, please mount the LED strip using
zip es and the 3M tape on the back of the strip.
- Using 2 self-tapping screws, drill each end of the
strip. Repeat each step for every side.

- You will mount the aluminum strips using the 3M
adhesive tape and 2 self-tapping screws (1 for each end)
- Do not leave any loose cables and always use proper cable
management when roung cables through the engine bay and
underbody.
- Once you’ve mounted all the LED strips, you will need
to run the extension cables to the engine bay. Make sure
when running the cables, you don’t zip e them to the
exhaust or any surface that might release heat.
- By this engine bay.
Locate
the
the connectors
on harness.
the
proper way.
point, you should have all four extension cables on
four connector driver and connect each cable to one of
the Please make sure every connecon is connected the
- The locang a place
in locatedthe red
wire to
the
baery.
driver will come with 1 red wire (power) and 1 black wire (ground) Start by
engine bay to add the ground wire. Once your ground terminal is secured,
and connect it the
- Download LED Hue from Play Store or App
Store
- Open app and scan for available devices,
search for “litlightz” or “SP110E”
- Set sengs to the following: SK6812,
Pixels:150
RGB
Please refer to local and state laws for the proper use of this product! Improper installaon of electrical
products such as lighng could cause damage to a vehicle’s electrical system or connected devices.
Pracce extreme cauon and follow all established safety procedures. This product could require
the handling of high voltage wiring. Electricity could cause injury or death. Professional installaon
is recommended. Lit Lightz will not be held responsible for any damage or cost whether direct or
indirect incurred by the consumer in relaon to any Lit Lightz Product. Lit Lightz reserves the right
to alter or amend any poron of the aforemenoned disclaimer.