Litecraft LED PAR 64 AT3 User manual

LED PAR 64 AT3
MANUAL
Thank you for purchasing this LITECRAFT product. For your own safety, please
read the instruction manual carefully before turn on the product for the first time.
SAFETY NOTES
•Each person which is responsible for the installation, the use or service
of this unit must be:
- qualified
- has to follow the instructions in this manual.
•WARNING! Be careful when using the device. You risk an electrical
shock from high voltage, if you touch the wires!
•The device has left our company in manufacturer proofed state. To
maintain this status and to ensure a permanent safe operation, it is
absolutely necessary to follow the safety instructions and warnings in
this manual.
•IMPORTANT: Errors, caused by not following these instructions are not
covered by the warranty. The manufacturer will not accept liability for any
resulting defects or problems.
•Keep the unit away from radiators or other heat sources!
•If the unit has been exposed to tremendous temperature changes (e.g.
after transportation), do not turn it on immediately. The resulting
condensation could damage the unit. Don`t switch unit on until the
device reaches room temperature.
•This device belongs to protection class I. Therefore, it is imperative that
the green/yellow wire is connected to the earth contact of the plug. The
electrical connection must be made by a qualified person.
I

•Make sure that the cable has never been squeezed or damaged by
sharp objects. Check the device and the cables regularly.
•If the cable is damaged, it must be replaced immediately by the
manufacturer, its service agent or a qualified person in order to avoid
danger.
•Lenses, glasses or UV filters must be replaced if they are visually
damaged, or their effectiveness is impaired, e.g. by broken glass or by
deep scratches.
•Ensure that wires never come in contact with other wires! Handle the
power cord and all connections with caution!
•Make sure that the line voltage is not higher than the voltage specified in
this manual.
•Disconnect the unit from the AC mains when it is not in use or when
cleaning it. Disconnect the connection only by pulling the cable plug.
•Using the fixture for the first time, can result in light smoke and odors.
This is a normal process and does not constitute a defect.
•RISK OF BURNS! Do not touch the unit during operation! The housing
may reach high temperatures.
•RISK TO HEALTH! Never look directly into the light source. Especially
epileptics risk an epileptic shock! Disconnect the unit from the AC mains
when not in use or when cleaning it.
•Defects caused by modifications of the device by unqualified handling or
an unqualified person are not covered by the warranty.
•Keep the product away from children and unskilled people.
•There are no wear parts in the device. Maintenance and service must be
performed only by an authorized service partner.
II

OPERATION
•This device has several DMX- and Stand-Alone-Modes. In DMX-mode,
multiple devices can be connected and controlled by a controller. The
device accepts the settings of the DMX-controller, as soon as the
corresponding start address is set.
•Slave mode:
Connect the DMX-output of the master device (XLR female) to the
DMX-input of the slave device (XLR male). Set the slave device to
DMX-mode 3 with the DMX-start address 001 (display shows: 3001).
The slave device accepts all settings of the master device (such as color
changing audio triggered color macro, programm, audio programm,
programm speed).
•Display description:
The display shows the different DMX-modes & the DMX-start address or
color changing audio triggered color macro, programm, audio programm,
programm speed; the first digit shows the mode, the last three digits the
corresponding value. If a DMX-mode is choosen, the DMX-LED flashes
fast to show the DMX signal is present. If master/slave is choosen the
DMX-LED lights up permanent on master unit and flashes fast on slave
unit.
•Button description:
Press the MODE button repeatedly to select the mode. Press the UP or
DOWN button to set the DMX-start address or any of the
pre-programmed modes or the speed values. Use the UP button to
increase the value. Use the DOWN button to decrease it.
NOTE!
If you hold the UP or DOWN button for longer than 3 seconds, the value
changes faster. The device has an automatic storage for all settings.
When you turn the device off and on again, it works with the previously
set values.
III

IV
CONTROL MODES / DMX DESCRIBTION
mode display function
1 channel mode 1***, *** = DMX
adress ch1 = color macro mode (35 colors + black)
2 channel mode 2***, *** = DMX
adress ch1 = color macro mode (35 colors + black)
ch2 = dimmer
3 channel mode 3***, *** = DMX
adress ch1 = dimmer red ch2 = dimmer green
ch3 = dimmer blue
DMX-
mode
7 channel mode 4***, *** = DMX
adress ch1 = dimmer red
ch2 = dimmer green
ch3 = dimmer blue
ch4 = color macro mode
0-13 no macro
14-255 pre-programmed colors
ch5 = strobe/speed
0-15 no strobe
16-255 strobe 16 speed values
ch6 = mode
0-35 no function
36-71 automtic ramp up */**
72-107 automatic ramp down */**
108-143 automatic ramp up/down */**
144-179 automatic color mix mode
180-215 random 3-colors *
216-251 random 7-colors *
252-255 audio mode
ch7 = dimmer
* speed value by channel 5
** color value by channel 1, 2, 3
audio
mode color changing audio triggered 5-So – no setting possible color change triggered by audio signal
color macro
mode 6***,*** = pre-programmed
colors
choose one of 35 pre-programmed colors +
black
color programm
mode 7***, *** = pre-programmed
chaser
choose one of 6 pre-programmed chasers
audio programm
mode 8*00,*00 = audio trigger active audio trigger for the color programm choosed in color programm mode
manual
mode
programm speed 8***,*** = speed
value choose one of 16 speed values for the programm choosed in programm mode
TECHNICAL SPECIFICATION
voltage 100-240 V, 47-63 Hz
power consumption 0.3 A @ 230 V
measurements 274 x 268 x 433 mm
weight 3.5 kg
fuse T3.15 A @ 250 V