Lites Lites F 200 Instruction Manual

Lites
Lites F 200
Owners ‘s & Service manual
Read this manual totally and carefully follow all the instructions contained. File this manual for future
use. It is essential to read all the information contained to ensure installation, service and full o eration
of the LitesF200.
All o erations must be accom lished, handled and carried out by qualified ersonnel only. Not com lying
with given notice will void warranty and will free manufufacturer from any liability/res onsability
http://www.ilites.eu

Pagina 2 di 8
Unpacking
Unpack the carton and gently remove LitesF200 rom the box. Ensure LitesF200 received is integer rom origin in all its
components.
In the event the LitesF200 shows any damage, do not use it and contact immediately your transporter as well as your
seller.
Items in the carton consist o :
− LitesF200 luminaire
− Colour rame
− Blue Neutrik PowerCon connector
− This owner's and service manual
Safety information for the use of the LitesF200 as well as its periodical maintenance”
 LitesF200 is or pro essional use only and NEVER or domestic use there ore re rain rom this latter utilisation.
 Users must scrupulously comply with in ormation that ollows, any other use in contrast will void warranty and
will ree the manu acturer o any sort o responsibility and liability.
 Never use LitesF200 on any lammable sur aces.
 Minimum distance rom any lammable source is o 0.25m.
 Minimum throw distance rom illuminated sur ace: 0.5m.
 Installation o the unit(s) must be secured with adequate clamps, sa ety cords, nuts and bolts to bear the
weight o the whole unit(s)
 Always Power LitesF200 to sa ety circuit breakers. LitesF200 must NOTand CAN NOT be operated via Phase
Control Dimmer.
 Install LitesF200 in ventilated ambient which temperature must not trespass 35°C
 Some outer parts o the LitesF200 can reach temperatures o up to 60C° when in operation.
 LitesF200 must be itted with protection shields (Lenses)
 On no account, directly or indirectly, LED must be touched
 Always disconnet power, (always double check that power is o ) be ore any Service/Operation o the unit.
 LitesF200 is rated Class I.
 Earth connection is MANDATORY!
An essential and periodically throughout cleaning o the LitesF200 is recommended. This practice avoids that layers o
dust and other impurities jeopardise and reduce the correct operation o the unit. Lenses must be cleaned to remove
layers o dust that may impede and or reduce the passage o the light through the lenses. The correct and periodically
maintenance keeps also ans and vents clean to keep the LitesF200 in its best per ormance conditions. Never touch the
Yellow core o the LED both directly or indirectly nor use solvents that can damage the LED irremediably. Protection
shields i battered, must be replaced with new ones (Lenses)
CE APPROVALS
The HPLED products to which this manual re ers to, complies with European directive pursuant to:
2006/95/EC sa ety o electrical equipment supplied at low voltage (LVD)
2004/108/EC Electromagnetic compatibility (EMC)
2011/65/EU Restriction o the use o certain hazardous substances (RoHS)
WARRANTY
A 12-month warranty is granted on the LitesF200 rom its purchase’s date. Warranty covers abrication de ects only,
unit will not be replaced but will be 100% ixed. Warranty is immediately voided i the LitesF200 has not been handled
by quali ied personnel. Any improper and unauthorised use, such modi ication(s) or misapplication o the unit will also
void the warranty o the product(s). Silver colour label showing technical data and serial number, i removed or i data
are impaired to render details illegible, will immediately void the warranty.

Pagina 3 di 8
Technical specifications
Power Supply: 100/240V~ 50/60Hz (autosetting)
Maximum power consumption 200W (Citizen CLL050-CLL052) cos ø 0,98
Maximum power consumption 140W (Bridgelux BXRA/Vero) cos ø 0,98
Stand-by power consumption 5W
LED Colour temperatues and CRI : ASK INFORMATION at [e-mail]
Fresnel Lens: Ø 150mm
Colour rame dimensions: 195x185 mm (the use o standard 185x185mm colour rame is totally acccettable)
Aluminium die-caste body to maximize heat dissipation
Operating temperature range: -15°C + 35° C
Maxium temperature on the LitesF200 +60°C
Weight o the unit: Kg 6,9
Worm-gear beam adjustment on standard Lites200F/ Automatic zoom on LitesF200Zoom
Rear handle or good grip o unit ; side-lock on mounting yoke to adjust and set unit to position.
Beam angle: 18°-60°
Working position: +90°/-90° on vertical axe
Protection rating: IP 20
DMX 512 , RDM, Protocols (wireless on request)
Neutrik powercon IN & OUT connectors
Neutrik XRL5 IN & OUT signal connectors
4-digit display
Manual operation via 4-digit display
Idle an mode or totally silent use o the unit.
Adjustable LED requency
Selection o two LED dimming curves
Comply with
Dimensions: see igure

Pagina 4 di 8
Lites200F installation
Lirtes200F is delivered with a robust yoke which hosts 3 x 12 mm mounting holes.
The use o an adequate G-clamp to sustain at least twice the weight o the Lites200F (Lites200F weighs 7,9 kg)
and/or M10 screw is mandatory. The use o sa ety chain(s) to sustain twice the weight o the Lites200F is also
mandatory, the sa ety chain adds more protections to users and third-parties. Eye-lid or the sa ety chain is provided
on the LitesF200. (see Fig)
The Lites200F yoke revolves on 360° on the projector’s axis. Lites200F can be installed +-90° on the vertical axis.
(see Fig.). Best Lites200F’s per omrances are achiieved i unit is installed as shown in the illustrations that ollows.
(never install LitesF200 upsidedown, illustrations that olllows show installation positions that must be avoided) .
Incorrect installation(s) can, immediately or in short/long terms, jeopardise the correct operaton o the LitesF200.
Incorrect installations may voide the warranty o the unit.
90°
90°
AVOID INCORRECT INSTALLATIONS AS ILLUSTRATED

Pagina 5 di 8
Installations of the accessories
LitesF200 is delvered with a standard
195x185mm colour rame (standard colour
rame 185x185 can als be used). The LED
source used on LitesF200 allows the use o
colour ilters that cannot be used with high
wattage tungstene lamps which would impair
colour ilters. Optional and standard 185x185
mm 4-lea -barndoor can also be installed in the
provided gates. Ensure that accessories when
installed on the LitesF200 are securely itted in
the gates and that are triggered and secured by
the spring-lock provided. (see igure)
Beam adustment
Lites200F can revolve +-90° upwards and +-
90° donwwards on the axis o the luminaire.
When correct position is set to position, secure it
by tightneing the provided side knob. Beam
adjusment is achieved via rear Helicoidal screw.
Turn clockwise to narrow beam, conversely
beam widens.
Connection to mains
WARNING ! Installation(s) must be accom lished, handled and carried out by qualified ersonnel only and
must com ly with all norms in force in the installation's country
LitesF200 is supplied with a ree Blue Neutrik PowerCon plug that must be wired using a 3x1.5mm² lead , additional
speci ications include:
 Operating Voltage: 300/500V
 Test Voltage: 2KV
 Operating Temperature: -10°C / +100°C
Connect blue wire to N terminal, brown wire to L terminal and Yellow/Green wire to earth terminal. (see also illustration
ig) Ensure connections to sa ety circuit breaker at all times. Daisy chain o up to maximum 8 units i connected to
230VAC. Daisy chain o up to maximum 4 units when connected to 110VAC. Maximum daisy chain length: 25m.
WARNING: LitesF200 CANNOT be owered by using an angle hase dimmer ack
Collegamento alla rete elettrica
POWER IN
A
POWER OUT
ZOOM
-
+
A

Pagina 6 di 8
UP
Down
Enter
Esc
Signal Control Connection
LitesF200 can be operated via either DMX512A and or RDM ready . For dasy chain connection use a -2 x 0,5 mm²
size lead wire plus shield. Connect Pin 1 to ground, 2= data – while Pin 3 = data +. Pins 4 & 5 are not connected.
Ensure that DMX wires and shield do not inter ere,nor touch each other as well as they must not touch/inter ere with
the body o the unit . (DMX connectors are not provided)
Im ortant note: when DMX is available a red dot will illuminate on the left hand of the dis lay.When
red dot is off no DMX signal is available.
WARNING ! Before owering LitesF200 ensure that all installation(s) rocedure(s) have(s) been
ro erly set and accom lished
DMX OUT
DMX IN
Projector mode settings
When LitesF200 is powered, setup-display will show the so tware release version The UP,
DOWN, ENTER and ESC buttons will allow the operations o the LitesF200 menu. UP and
DOWN buttons allow to scan menu options, ENTER button allow to select. The ESC button is
to retun to the previous menu or to quit the previous setting.
Menu items
Dis layed
message
Allowed or dis layed
values Mode
Addr
001..510 DMX address : as o 1 to 510
Mode
1 ch
2 ch
3 ch
4 ch
5 ch
DMX Operating mode (see next page)
Man
0..255 Manual light output adjustment (This is possible even i no DMX is
resent). Adjusted value will be stored on the internal permanent memory
drUt
..°C Shows driver operating temperature
LEdt
..°C Show led operating temperature
PUM
0..100% Shows current led power (0-100%)
SMOO
FAST
MED
SLOW
DMX data Speed adjustment
GAMM
LInE
qUAd
Dimmer pro ile selection:
- LinE or linear dimming regulation
- qUAd or tungsten lamp emulation)
booS
O
on
Boost selection:
o = maximum led power at 90%
on = maximum led power at 100%
PoS
AA
VV
I Display orientation selection:
AA = normal
VV = inverted
StbY
O
on
Standby display activity:
o = display always switched on
on = display switched o a ter ew seconds o buttons inactivity (only
the right side dot will be lighted to indicate DMX availability)
dEF
O
on
ON Will restore the de ault actory values
TiML ..h ..
Shows LED li e
TiMU ..h ..
Shows HPLed li e
SoFt
Shows So tware version
XLR 5
connection
leads
descri tion
1 GND
2 DMX-
3 DMX+
4 NC
5 NC

Pagina 7 di 8
DMX O erating Modes (Mode)
LitesF200 provides with di erent DMX operating modes ensuring the ideal use o the DMX universe
Shutter/strobo, 8/16 bit dimmer, an speed and LED requence are all adjustable
mode a 1ch
Ch unzione Livelli dmx
1 dimmer 0..255
Light output: 0=O , 255=Maximum Power
mode a 2ch
Ch unzione Livelli dmx
0-9 o 1 shutter
10..255
Strobe e ect rom slow to ast
2 dimmer 0..255
Light output: 0=O , 255=Maximum Power
mode a 3ch
Ch unction dmx values
0-9 o 1 shutter
10..255
Strobe e ect rom slow to ast
2 dimmer 0..255
Light output: 0=O , 255=Maximum Power
0..24 Fan o 3 Fan speed
24..255
Fan adjustement rom minium to max value
mode a 4ch
Ch unction dmx values
0..9 o 1 shutter
10..255
Strobe e ect rom slow to ast
2 dimmer 0..255
Light output: 0=O , 255=Maximum Power
0..24 Fan o 3 Fan speed
24..255
Fan adjustement rom minium to max value
0..24 pwm requency 5,1KHz
25..49 pwm requency 5,2KHz
50..74 pwm requency 5,3KHz
75..99 pwm requency 5,4KHz
100..124 pwm requency 5,5KHz
125..149 pwm requency 5,6KHz
150..174 pwm requency 5,7KHz
175..199 pwm requency 5,8KHz
200..224 pwm requency 6KHz
4
LED Frequency
Modulation
( lickering)
225..255 pwm requency 610Hz
mode a 5ch
Ch unction dmx values
0..9 o 1 shutter
10..255
Strobe e ect rom slow to ast
2 dimmer 0..255
Light output: 0=O , 255=Maximum Power
3 Dimmer ine 0..255
0..255 ine dimmer adjustment
0..24 Fan o 4 Fan speed
24..255
Fan adjustement rom minium to max value
0..24 pwm requency 5,1KHz
25..49 pwm requency 5,2KHz
50..74 pwm requency 5,3KHz
75..99 pwm requency 5,4KHz
100..124 pwm requency 5,5KHz
125..149 pwm requency 5,6KHz
150..174 pwm requency 5,7KHz
175..199 pwm requency 5,8KHz
200..224 pwm requency 6KHz
5
LED Frequency
Modulation
( lickering)
225..255 pwm requency 610Hz

Pagina 8 di 8
Error messages
In case o mal unction, the ollowing messages may be shown:
LED ERROR : sympthon o a possible short-circuit on LED driver.
TEMPERATURE ERRor: sympthon that sensors have measured temperature below -15°C or ailure on NTC- in such
event LED will switch to o mode. Should any o the above given messages occur, or precaution measures the LED
will always switch to o mode. Halt the unit immediately and re rain rom the use o it and promptly contact any
authorized service centre.
Periodical maintenance
To ensure the correct LitesF200’s operations we suggest the ollowing periodical maintenance operations:
Remove dust or any kind o other dirty rom the ans and loop-holes to ensure the correct air low
Remove dust rom lenses using a clean cloth. This maintenace will ensure the maximum light e iciency
Replace damaged protection screens and lenses when necessary
Always handle LitesF200 gently and with care, do not drop, do not shake do not cause shocks to the unit as it could
damage it irremediably.
Do not touch nor clean the LED as well as the yellow area around it with solvents
Device dis osal information
At the end o its li e, LitesF200 must be disposed to an appropriate electrical and electronic equipment
waste collection centre. Eco- riendly disposal, helps to avoid possible negative impact on the
environment and human health and promotes the reuse and/or recycling o the materials making up
the product. Illegal disposal involves administrative sanctions provided by laws enacted.
Manu acture declines any sort o personal/corporate responsibility/liability or damages caused by the inadequate use
o the product as well as i unquali ied personnel have handled the product. Not complying with security
norms/periodical maintenance as expressed in the owner's/service manual will also totally ree personal/corporate
responsibility/liability.
Lites F 200 White 04/11/2013 rev.01