Little Partners LPA1103 User manual
!KEEP INSTRUCTIONS FOR FUTURE USE
!READ all instructions BEFORE assembly and
USE of the product.
!Check installation after assembly and
periodically at least once a month to
ensure unit correctly installed.
!Adult assembly required.
!CAUTION: FOLLOW ASSEMBLY
INSTRUCTIONS OF THE PRESSURE GATE
AS EACH GATE MAY ASSEMBLE
DIFFERENTLY.
While one
person can
assemble this
item, it is
recommended
that two people
work together
for easier
assembly.
PRN: AIM-LPA1103-LPN [16.09.14]
PART LIST
Grip Tape
Silicone
Anti Slip
Material
Light
(x1)
Front View Back View
LPA1103
EZ-FIT CHILDREN'S AND PET GATE WALL PROTECTOR WITH LIGHT
(x1)
Front View
Silicone
Anti Slip
Material
PPI Label Location
LPA1 LLC.
Model #: LPA1103-X
Date Code: MMYYYY-ZZZ
Back View
Grip Tape
Large Panel Small Panel
1
!Keep the batteries out of children's reach.
!Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in
backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new
batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
!Any battery may leak battery acid or explode if disposed of in fire or an attempt is made to charge a
battery not intended to be recharged. Never recharge a cell of one type in a recharger made for a cell
of another type.
!Discard leaky batteries immediately. Leaky batteries can cause skin burns or other personal injury.
When discarding batteries, be sure to dispose of them in the proper manner, according to your state
and local regulations.
!Always remove batteries if the product is not going to be used for a month or more. Batteries left in the
unit may leak and cause damage.
!Recommended type batteries—alkaline disposables, 3AAA. NEVER mix battery types. Change
batteries when product ceases to operate satisfactorily.
TROUBLESHOOTING:
If your device is not functioning properly, check for the following problems:
1. No batteries in electronics module.
2. Batteries dead.
3. Batteries in backwards—check “+” and “-”.
4.Corrosion on battery terminals. Rotate batteries in place against terminals, or clean with sandpaper or
steel wool if corrosion is severe.
5. Batteries too weak.
If you still have problems, call our toll-free number: 1.800.704.9058 or
email: [email protected]
IMPORTANT INFORMATION REGARDING BATTERIES
USEFUL TIP
LIGHT ASSEMBLY INSTRUCTION
3
BATTERY INSTALLATION
21
OPEN
UNSCREW
AAA 1.5V
AAA 1.5V
AAA 1.5V
45
CLOSE
Three AAA Batteries required. NOT
included. Align batteries as shown
on inside of compartment.
AAA
6OFF
ON
Your light has an ON/OFF switch. Push in to
activate the sensor light. Push in again, to
prevent light from coming on when Motion
occurs around light. Once batteries are installed
it is recommended to test your light to ensure
product works correctly before you install onto
the base. To do this, turn on the light and find a
dark area and move hand in front of sensor.
Light is programed to stay on for 15 seconds.
7 8 9
2
10 11
NOT ALIGNED
UPSIDE DOWN
INSERT TILL LOCK 'CLICKS'
3
LOCATION OF YOUR EZ FIT WALL PROTECTOR WITH LIGHT
LOCATION OF YOUR EZ FIT WALL PROTECTOR
CAUTION: FOLLOW ASSEMBLY INSTRUCTIONS OF THE PRESSURE GATE
AS EACH GATE DIFFERS SLIGHTLY FOR CORRECT INSTALLATION.
TOP
REMOVING THE LIGHT
UNLOCKED
PUSH
REMOVE
12
TIGHTEN GATE
Insert a small pointed tool,
such as a paperclip or
pencil, into the hole to
depress the tab to unlock.
13
14 15
16 17
Assembly of your EZ Fit protector is easier if you have help. An extra set of
hands to hold the unit in place while you tighten the gate is recommended.
TOP TIGHTEN GATE
TOP
4
PRODUCT PACKAGING INFORMATION
Model #:
Color:
Distributed by
LPA1 LLC.
501 South 9th Street
Reading, PA 19602 USA
Email: [email protected]
Toll Free: 1.800.704.9058
MADE IN CHINA
Shipment Ref.#.
Date Code:
WALL
TWO SETS - Top and Bottom on both side on
first step. Need a second set of two small
round EZ Fit Protectors please call or order on line
EZ-Fit Gate
Adaptor kit
One SET - Top and Top on both sides of
wall with base boards
One SET- Top and Bottom on one side on
first step. And EZ-Fit Gate Adapter kit.
To order the EZ fit gate call or order on line.
One SET - Top and Top on both sides of
wall with base boards
DIFFERENT OPTIONS FOR YOUR EZ FIT PROTECTORS
N A
WALL
