Livestrong LS9.9T User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
LS9.9T
LS12.9T

2
LIVESTRONG™ is a registered trademark of the Lance Armstrong Foundation.
The Lance Armstrong Foundation fights for the more than 25 million people around the world living with cancer today. There can be – and should be – life after cancer for more people. They
kick in at the moment of diagnosis, giving people the resources and support they need to fight cancer head-on. They find innovative ways to raise awareness, fund research and end the stigma
about cancer that many survivors face. They connect people and communities to drive social change, and call for state, national and world leaders to help fight this disease. Anyone, anywhere
can join the fight against cancer. Join them at LIVESTRONG.org.
INTRODUCTION
Congratulations and thank you for your purchase of this LIVESTRONG™ treadmill!
Purchases of this product ensure that a minimum of $4M will go to the Lance Armstrong Foundation and the fight against cancer.
Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a LIVESTRONG™ treadmill can help you
attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you
need to get stronger and healthier, faster. Because we’re committed to designing fitness equipment from the inside
out, we use only the highest quality components. It’s a commitment we back with one of the strongest frame-to-motor
warranty packages in the industry.
You want exercise equipment that offers the most comfort, the best reliability and the highest quality in its class.
LIVESTRONG™ treadmills deliver.

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located near the on/off
power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODLE NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: LIVESTRONG TREADMILL
WARNING

4
SPEAKERS
WATER BOTTLE HOLDER
GRIP PULSE HANDRAILS
SPEED/INCLINE TOGGLES
CONSOLE
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER CORD
READING RACK
CONSOLE FAN
IPOD/MP3 PLAYER POCKET
TOUCH PAD PANEL AND DISPLAY WINDOWS
SAFETY KEY PLACEMENT
MOTOR COVER
WHEEL LOCK
SIDE RAIL
ROLLER END CAP
REAR ROLLER
ADJUSTMENT BOLTS
CONSOLE MAST
FOOT LOCK LATCH (UNDERNEATH DECK)
RUNNING BELT / RUNNING DECK
CAUTION AVERTISSEMENT PRECAUCIÓN
KEEP HANDS AND FEET
AWAY FROM THIS AREA.
HIGH-PRESSURE
SHOCKS COULD CAUSE
BODILY INJURY.
GARDER LES MAINS ET LES
PIEDS LOIN DE CETTE REGION.
LES AMORTISSEURS À HAUTE
PRESSION PEUVENT CAUSER
DES BLESSURES.
MANTENGA LAS MANOS Y
LOS PIES LEJOS DE ESTA
AREA. IMPACTOS DE ALTA
PRESIÓN PUEDEN CAUSAR
DAÑO CORPORAL.
CAUTION AVERTISSEMENT PRECAUCIÓN
KEEP HANDS AND FEET
AWAY FROM THIS AREA.
GARDER LES MAINS ET LES
PIEDS LOIN DE CETTE REGION.
MANTENGA LAS MANOS Y LOS
PIES LEJOS DE ESTA AREA.
12
ABOVE FOOT LATCH
1
2

5
TOOLS INCLUDED:
F6 mm T-Wrench
F5 mm T-Wrench
FScrewdriver
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F2 Console Mast Caps
F2 Console Mast Boots
F2 Main Frame Boots
F4 Hardware Bags
F1 Safety Key
F1 Power Cord
F1 Audio Adapter Cable
F1 Bottle of Silicone Lubricant
(for 2 applications)
If you have questions or if
there are any missing parts,
contact Customer Tech
Support. Contact information
is located on the back panel
of this manual.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. The enclosed
treadmill is equipped with high-pressure shocks and may spring open if mishandled.
Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NEED HELP?
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY

6
BOLT (A)
20 mm
Qty: 6
SPRING WASHER (B)
8.2 mm
Qty: 6
ARC WASHER (C)
8.2 mm
Qty: 6
HARDWARE BAG 1 CONTENTS :
BOLTS (A)
MAIN
FRAME
BOOT
CONSOLE MAST
SPRING
WASHERS (B)
ARC WASHERS (C)
MAIN FRAME BRACKET
CONSOLE CABLE
LEAD WIRE
ASSEMBLY STEP 1
A Cut the yellow banding straps and lift the
running deck upward to remove all contents
from underneath the running deck.
B Open hardware bag 1.
C Slide main frame boot up console
mast. Place right console mast over
main frame bracket.
D Pull lead wire through right console
mast. After pulling the lead wire through
the mast, the top of the console cable
should be located at the top of the mast. Detach
and discard lead wire.
NOTE: Do not pinch console cable when
placing the mast onto the main frame
bracket.
E Attach console mast to main frame
bracket using 3 bolts (a), 3 spring
washers (b) and 3 arc washers (c).
F Slide main frame boot down over main
frame bracket.
G Repeat steps D–F on other side.

7
ASSEMBLY STEP 2
A Open hardware bag 2.
B With the console upside down, attach the
console mast caps to the console
using 4 bolts (e) and 4 spring
washers (b).
BOLT (E)
15 mm
Qty: 4
SPRING WASHER (B)
8.2 mm
Qty: 4
HARDWARE BAG 2 CONTENTS :
BOLTS (E)
SPRING WASHERS (B)
CONSOLE (UPSIDE DOWN)
CONSOLE MAST CAP
NOTE: The console mast caps are marked with an
L if they are to be used on the left-hand side of the
treadmill or an R if they are to be used on the right-
hand side of the treadmill. If the console mast caps
are assembled on the incorrect side of the treadmill,
the unit will not assemble correctly.

8
ASSEMBLY STEP 3
A Open HARDWARE BAG 3.
B Slide CONSOLE through the CONSOLE
MAST BOOTS.
NOTE: Make sure the arrows on the mast rings
are pointing upward towards the console when
sliding into place.
C Connect CONSOLE CABLES.
D Connect CONSOLE to RIGHT CONSOLE
MAST using 2 BOLTS (A), 2 SPRING
WASHERS (B) and 2 ARC WASHERS (C).
E Repeat on other side.
NOTE: Be careful not to pinch any wires
while assembling the right console mast.
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
8.2 mm
Qty: 4
ARC WASHER (C)
8.2 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
BOLTS (A)
CONSOLE MAST
SPRING WASHERS (B)
CONSOLE MAST BOOT
CONSOLE CABLES
CONSOLE
ARC WASHERS (C)

9
YOU ARE FINISHED!
ASSEMBLY STEP 4
A Open HARDWARE BAG 4.
B Attach MAIN FRAME BOOTS using 4
SCREWS (D).
C Before the first use, lubricate the treadmill
deck by following the instructions in the
MAINTENANCE section in the TREADMILL
GUIDE.
SCREW (D)
20 mm
Qty: 4
HARDWARE BAG 4 CONTENTS :
SCREWS (D)
MAIN FRAME BOOT

10