Living Culture Villa User manual

1
User Instructions
Villa Pergola for motorised operation
Size:600x400 cm (double bay)

2
Content
Tools and man force ...........................................................................1-2
Parts List.............................................................................................2-5
Product Description..............................................................................6
Safety Instruction..................................................................................6-7
Mounting................................................................................................8-17
Dismounting...........................................................................................18
Storage...................................................................................................19
Disposal..................................................................................................19
Attention:
Read this instruction manual carefully and completely before mounting and
usage. Keep this manual for future reference.
Dear Customer,
Congratulations and thank you for choosing to buy the Villa Pergola from our company. To enjoy this product for a
long time and for your own and the safety of other people, please follow the assembly instructions.
Before you start the assembly process and then using the Pergola, we suggest you are best to get familiar with this
product. Make sure all parts listed up in below packing lists are delivered and intact. If you find that there are parts
missing or damaged please do not install the pergola but contact us immediately. Do not start the assembly process
if parts are missing or defective.
Tools and man force
Recommended: 2 or 3 people
Additional tools :
1.Ladder 2. M10/13 open wrench supplied 3.Rubber mallet
4.Tape measure 5. 5mm hexagon wrench supplied 6.Pencil
7.Spirit level 8.Electric drill

3
Parts List
Please check all parts against the parts list before commencing construction of pergola.
SIZE：600X400CM (double bay) PARTS LIST

4

5
Hardware and other parts:
①M8x20 countersunk screw
②Screw for motor fixing
③Base plate
④Upright cover
⑤M10 screw cap
⑥M8x20 Hexagon bolt
⑦Plastic Spacer
⑧Locking nut
⑨Motor 1 with motor bracket
⑩Motor 2 with motor bracket
⑪M8X100 expansion bolt
○
12 Gutter connector
○
13 50 to 40 connector
○
14 2 Remotes
Aluminum profile parts list:
(A-1) Beam /(A-4) Beam
(A-2 )Beam with motor direction left & slots
(A-3)Beam with motor direction right & slot
(A-5)Middle beam
(B-1)Gutter
(B-2)Gutter
(B-3)Middle Gutter
(C-1)Post + post connector
(C-2)Post + post connector
(C-3)Post + post connector
(C-4)Post + post connector
(C-5)Middle Post + post connector
(D-1)Common louver
(D-2)Centre louver
(D-3)Driving louver
(E)Control rod

6
Product Description
Make the most of your outdoor living area with your pergola. Relax and enjoy the outdoors while being protected
from sun. The coated aluminum frame pergola is perfect for shading your garden, deck, courtyard and swimming
pool.
Important Safety Instructions
Warning: For the safety of you and other persons it is important to follow below instructions and obey
warnings.
Symbol explanation
This warning triangle calls attention to hazards that that can lead to death or to severe
injuries or which are important for the functioning of the Pergola.
This sign identifies important notes.
Safety instructions
To install this pergola technical knowledge is necessary. Do not mount this
pergola yourself but contact a professional workman for help if
you are unsure if the pergola can be mounted on the place you chose for
installation.
you do not understand the instruction manual or parts of it.
you do not have necessary tools available.
you do not have necessary technical knowledge
A minimum of three healthy adults are required to move and install the pergola
as the product is big and heavy. Do not try to install the pergola alone. If the pergola
falls, it could cause serious injuries and damages! Contact an authorized assembler for
help.

7
Do not install the pergola when you find damage parts are that parts are missing.
Contact your dealer.
Keep children and pets out of the working area during assembly and
adjustments.
This product and its fixing parts are only suitable for installation on a plain
cement wall or stable brickwork. If the wall/brickwork shows cracks you have to
consult a professional.
Nobody is allowed to change the products’ design and structure without the
permission of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly; otherwise you
may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola is
forbidden.
Sheeting was used to protect the paint. This must be removed afterwards.
This structure is a non-permanent structure and the warranty does not cover damage
incurred under extreme weather conditions including heavy rain, high winds or if
exposed to high heat from heaters or BBQs.
Safety precautions should always be followed when assembling and using this product
to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use. Never leave children unattended around/under
this pergola. Do not attempt to assemble or use the pergola in moderate or heavy wind
conditions. Always keep the pergola louver open and secure it during heavy winds or
extreme weather conditions to avoid damage to the pergola or personal injury.

8
Mounting and usage
Step 1
Attach base plate ③x6 to the bottom of posts (C-1 X1,C-2 X1,C-3 X1,C-4X1,C-5
X2),use bolts①x12 to attach with hex key or electric drill.
C-1&C-3 ,C-2&C-4, C-5&C-5 posts should be installed diagonally as below.
Please make sure all posts on the same horizontal plane.

9
Step 2
Attach beam A-1X2 ,beam A-4 x2 ,beam A-2x1,beam A-3 x1 ,beam A-5 x1,use bolts
⑥x32 to fasten.

10
Step3
Use bolts ⑥x4 to fasten beam 1 & beam 4.

11
Step4
Attach upright cover ④x4,use bolts ⑥x8 to fasten

12
Step 5
Attach all eight gutters B-1X4,B-2X2,B-3X2 by hooking inside the A-1,A-2,A-3
beams.
Remark: Please put some silicon on the connection between the gutters & middle beams&middle
posts after installation.

13
Step 6
Located holes in centre of beams(A-2,A-3,A-5)
Place centre louver D-2intohole which on slot beam A-2,A-3,A-5, lining up with the
holes for 600*400 cm size.
Using M10 nut ⑤X2, secure the louver in place
Place Driving louver D-3in line with 7th slot (check attached direction）on the
beam A-2,A-3,A-5,
Fit all common louvers D1 into the remaining slots in the beams

14
Step 7
Fasten motor ⑨x1+○ 10 X1as shown below.

15
Step 8
Fasten ○ 12 x4 gutter connector and○ 13 x2 (50 to 40 connector).
Connect the female and male plugs for the LED lighting
(DC24V to DC24V) and motor (DC24V to DC24V) and
plug the power cable into local socket.

16
Step 9
Fix ○
Ex 4 (flat L-shaped aluminum profile).
One for each other of the slats is required.
Use bolt⑥x128, plastic spacer⑦x128 and nut⑧x128 to tighten for 600X400cm size.
Secure the louvers at each end.
NOTE: Do not over tighten. Over tightening will prevent louvers from moving.

17
Step 10
Mark holes for expansion bolt ○ 11 x4 on each post.
Note the drill size should be 12 mm.
Insert the bolts. Use an hammer drill if necessary. Place the posts
over the bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is used along
all corners and gutters to waterproof.
WARNING: Ensure louvers are open during periods of mild to strong winds.

18
Motor setup

19
Dismounting
If you want to disassemble the Pergola, please follow the following process.
Attention! At least two people are needed for this step.
Keep the Pergola louvers open before you begin with dismounting. Bind the Louvers of the Pergola together to
avoid unintended unfolding. This might cause damage and injury. You can use the protection band that was
fixed on the Pergola when purchasing it.
Follow the mounting instructions in reversed order to dismount the Pergola.
Make sure that drilling holes in the wall will be sealed professional.
Attention! Safety hints and instructions have to be followed for dismounting as well.
Storage
When you do not want to use the Pergola for a longer period of time it is recommended to take the Pergola out of
the brackets and store it.
Make sure that the frame is dry completely before storing.
Store the Pergola at a dry and safe place that is not reachable for children.
Disposal
Do not dispose this Pergola with other household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling. Dispose packing materials
according to local guidelines.