Living Earth Crafts Aspen GT User manual

Aspen GT Multi-Purpose Table
USER MANUAL
1-400-0019 • Rev B • 2/7/20
© Living Earth Crafts 2020, All Rights Reserved
*all tables shown with oponal accessories and/or nishes

© Copyright 2020
Living Earth Cras®
All rights reserved. is document or any
portion thereof may not be reproduced
in any way, including photocopying or
translation to another language without
the prior written permission from Living
Earth Cras.
Living Earth Cras® is a registered trade-
mark of Earthlite, LLC.
Legal Notice
e information provided in this document is intended
for informational purposes only and is subject to change
without notice. e information provided in this docu-
ment should not be construed as a commitment by
Living Earth Cras®.
Living Earth Cras® assumes no responsibility for the
accuracy or suitability of the information contained in
this document. is document may contain technical
inaccuracies or errors. Living Earth Cras® makes no
expressed or implied warranties of any kind concerning
the information contained in this document, including,
but not limited to, the implied warranties of merchant-
ability and tness for purpose.
Living Earth Cras® shall not be liable for incidental or
consequential damages in connection with or arising out
of the product, performance, or use of this document
and the information and material it describes.

Introduction
Congratulaons on your purchase of the Aspen GT mul-purpose table. It oers strength,
comfort and impeccable style, perfect for massage, facials, manicures or body treatments. The
Aspen GT is a striking yet versale addion to any treatment room.
Aspen GT tables are designed for licensed therapists and are intended to be used in a professional
spa, massage studio, or similar commercial environment. While no special training is needed to
operate the table, for safety reasons it is important that the instrucons contained in this manual
are reviewed in detail before the rst use. This manual should be read in its enrety by each
professional who will be operang the table to ensure the safety of both operator and client. This
manual should be saved for future reference.
The Aspen GT table should not be used in any other manner than described in this manual.
Please read, understand, and follow all safety warnings, labels, and instrucons. Misuse, use of
unnecessary force, or using the product for unintended or unauthorized procedures can result in
injury to operator, client, and/or equipment.
Detailed instrucons for use and maintenance can be found in this user manual. If you have
further quesons, please contact us at [phone] for US customers, or [phone] for
internaonal customers. We can also be reached via e-mail at info@livingearthcras.com
Secon 1: Safety Informaon
Safety Symbols
Warnings
Secon 2: Product Overview
Product Photos
Product Specicaons
Secon 3: Installaon
Moving Your Table
Basic Setup
Leveling Instrucons
Secon 4: Operang Instrucons
Important Safety Notes
Electrical Specicaons
Weight/Li Capacies
Hand/Foot Control Operaon
Secon 5: Care & Maintenance
Care Instrucons
Troubleshoong
Warranty Informaon
Contact Us
2
2-3
4
5
6
6
6
7
7
8
8-9
10
11
11
Table of Contents
back cover

READ AND SAVE THESE INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS - FOR COMMERCIAL USE ONLY
Read all instructions before using this product.
Safety Symbols
Familiarize yourself with the following
Safety & Warning symbols. They are
designed to prevent damage and injury
to you, your clients, and your new Living
Earth Crafts product.
IMPORTANT: The important safety
instructions and warnings in this manual
cannot cover all possible problems and
conditions that can occur. Use common
sense and caution when installing,
operating, or maintaining this appliance.
Indicates an imminently hazardous
situation which could result in serious
or fatal injury.
Indicates a potentially hazardous
situation which could result in serious
injury.
Indicates a potentially hazardous
situation which could result in
equipment damage and/or injury.
1) Always unplug this furnishing from the electrical outlet before servicing.
2) Never use this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination
and repair.
3) Keep the cord away from heated surfaces.
4) Do not use outdoors.
5) Do not operate where aerosol (spray) projects are being used or where oxygen is being administered.
6) To disconnect, turn all controls to the off position, then remove plug from outlet.
7) Connect this furnishing to a properly grounded outlet only.
RISK OF ELECTRIC SHOCK, FIRE, AND EXPLOSION
INTERNATIONAL VERSIONS ONLY
This product is for use on a nominal 220V-240V circuit and has a
grounding plug (plug type varies by country). Make sure that the
product is connected to an outlet having the same conguration as
the plug. No adapter should be used with this product.
NORTH AMERICA ONLY
Grounded
Outlet Box
Grounded Outlet
Grounding Pin
GROUNDING INSTRUCTIONS:
POWER SUPPLY: (120V AC grounded) Electrical limitations: Do not use extension cord with this product, plug
directly into grounded outlet. This product must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-grounding conductor and a grounding plug. This three prong grounded plug
will only t into wall outlet one way. If the plug does not t fully in the outlet, contact a qualied electrician to
install the proper outlet. Do not change the plug in any way.
SECTION 1: SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS 3
1) When lowering any section of the table, make sure that no supplies or any part of yours or your
client’s body is between the top of your table and its base. This could result in injury, or could
damage your table as well as the item. It is recommended that you always return your table top
to the lowest at position to avoid leaving the base exposed.
2) When lowering the table height, be sure there are no foreign obstacles are underneath your table
that could obstruct it from lowering completely. This could damage your table.
3) Never set anything under the table frame to avoid collision if lowered.
4) Never operate your table on an uneven surface. Adjust the leveling feet so that your table is stable.
5) Never raise the head or leg section with a client in the prone position (face down.)
6) Never use or store your table in a wet or very humid environment. Water and excessive moisture
can damage the wood cabinet and electrical components. Evidence of exposure to water or
moisture will void your warranty.
7) If you have purchased the Flexible Armrest Option, never use the Armrests as handholds or body
support mechanisms, especially when setting clients on or off the table.
8) Never drop or insert any object into any opening.
1) Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
2) Do not operate this equipment unless properly trained.
3) Install this furnishing in treatment area not accessible to the public.
4) Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons.
5) This product does not have “pinch point” protection. Only operate when no possibility of any portion
of the body could be caught and injured while moving the table top upward/downward, or activating
the back/foot tilt.
6) Do not use this furnishing to support video equipment such as televisions or computer monitors.
7) Never attempt to use the Head or Leg lift section to support concentrated weight such as sitting
or standing
To reduce the risk of burns, re, electric shock, or injury to persons:
SECTION 1: SAFETY INFORMATION

SECTION 2: PRODUCT OVERVIEW
4

Top Length 73” (185 cm)
Top Width 30”, 32” (76 cm, 81 cm)
Height Range 23.5” - 39.5” (59.5 cm - 100 cm)
Li Capacity 625 lbs (283 kg)
Product Specications
SECTION 2: PRODUCT OVERVIEW
*table shown with oponal accessories and/or nishes. Measurements may vary due to natural material variaons.
5
Feature Standard Oponal
Electric Spa Maress X
Naturso™ Upholstery X
Strata GT™ 5.5”
SpaMaress w/GelTech™ X
Ergonomic Hand Control X
Foot Control X
Milled Hardwood Base X
Sound System X
Ultraleather® Premium
Upholstery X
Flat Massage Top X
Included Features

Your Aspen GT table comes completely assembled and ready to use.
Once the table is unpacked, follow the “Moving Your Table” instruc ons below.
Moving Your Table
Basic Setup Instructions
Once your Aspen GT table is posi oned for use, follow these steps:
• Plug the power cord into an outlet that is properly rated for the table.
• Arrange and secure the power cord so it will not create a tripping hazard.
• Place the control(s) in a safe and accessible loca on.
• Ensure the control(s) are not in danger of being crushed by the li or  lt mechanisms.
• Follow the “Leveling Your Table” instruc ons below.
Leveling Your Table
Leveling, or balancing, your table is very important during ini al setup and rou ne maintenance.
Your Aspen GT table is equipped with leveling feet that can adjust to uneven fl oors.
To adjust the leveler feet:
1. Place the table in the posi on you plan to use it.
2. To determine which foot needs adjus ng, a empt to “rock” your table. If there is any
movement, the leg that is li ing is the one that will need adjus ng.
3. Raise table height approximately 6 inches.
4. Using your hand, or a wrench if necessary, turn the leveling foot in the needed direc on.
(Counterclockwise will lower the overall height, clockwise will raise the overall height)
Table Accessories
All Aspen GT tables come with outlets at both ends, speci cally designed for providing a  xed
loca on for FacePillow pla orms, salon pillows, and other accessories.
See the Living Earth Cra s website for all available acces-
sories that will  t into the table outlets.
Li your table by grasping  rmly from the bo om of the frame underneath the
upholstered top. Do not try to li from the upholstered top.
Your table is very heavy - extreme cau on should be used to avoid injury
to yourself, others around you, and your table. DO NOT li or move
without using proper safety procedures/equipment. DO NOT turn the
table on its side for any reason.
SECTION 3: INSTALLATION
6

Important Safety Notes
DO NOT store or place anything under the backrest - this can damage
the top and/or  l ng mechanism. This area is not designed for storage
or as an area to hold accessories and/or masage supplies while
performing any type of service. Placing anything in this area can cause
damage to the table and/or object and will void your warranty.
Always use extreme cau on when making any posi on adjustments to
your table. Ensure all body parts and objects are clear from all moving parts.
The described adjustments can be done with a client on the table, but use
cau on to ensure that the client’s weight is supported while posi oning the
table sec on(s).
Do not sit or put unnecessary amounts of pressure
on the back sec on of the table when it is in  lt
posi on of any level. This can damage or destroy the
 lt mechanism and cause harm or bodily injury to
persons. The  lt mechanism is intended solely to be
used when a client is properly seated or laying on the
table top. Damage caused in this manner may void
the warranty.
Do not sit or put unnecessary amounts of pressure
on the leg sec on of the table when it is in  lt
posi on of any level. This can damage or destroy the
 lt mechanism and cause harm or bodily injury to
persons. The  lt mechanism is intended solely to be
used when a client is properly seated or laying on the
table top. Damage caused in this manner may void
the warranty.
SECTION 4: OPERATING INSTRUCTIONS
Electrical Specications
*Other plugs also
available for various
countries
7
Spec North America Europe
Input Voltage 120 VAC 220 VAC
Input Frequency 60 Hz 50 Hz
Input Consump on 2.5A, 300 Wa s 1.36A, 300 Wa s
Consump on - LED Lights Addi onal 0.5 Amps Addi onal 0.28 Amps
Consump on - Breast Recess Addi onal 2.5 Amps Addi onal 1.38 Amps
Output 12-24 VDC 12-24 VDC

SECTION 4: OPERATING INSTRUCTIONS
8
Hand Control Operation
Your Aspen GT hand control is already connected and ready for use. See below for a
descripon of each buon’s funconality.
Weight & Lift Capacities
The Aspen GT is powered by a heavy-duty dual column electric li
actuator columns. The recommended li capacity is 625 lbs.
625 lbs.
The back secon and leg secon has a maximum weight capacity
of 50 lbs. These secons are not meant to hold full body weight.
50 lbs.
Lower Back Section
Lower Leg Section
Lower Entire Table
Trendelenburg Tilt
Lowers Foot End
of Table
Raise Back Section
Raise Leg Section
Raise Entire Table
Trendelenburg Tilt
Lowers Head End
of Table

Foot Control Operation
The foot control allows you to simply raise and lower the table, allowing convenient hands-
free adjustments.
9
SECTION 4: OPERATING INSTRUCTIONS
Lower Back Section
Lower Leg Section
Lower Entire Table
Trendelenburg Tilt
Lowers Foot End
of Table
Lower Entire Table Raise Entire Table

Category Care Recommendation
Upholstery
Remove day-to-day dirt and smudges with a mild soap and water soluon.
For tough stains and to disinfect, use a (100 to 1) water to bleach soluon.
Spray a damp cloth with the soluon to clean.
Aer each cleaning, gently wipe the upholstery with a damp cloth and clean
water, then allow upholstery to air dry before using or storing.
For more dicult stains, please contact your dealer or please call us directly
for guidance. For best results, use only the products suggested above.
Wood To maintain the wood nish and retouch scratches, use a high quality
furniture wax.
Electronics An-stac electronic aerosol dusters can be used to keep the surfaces of
electronic components, power cables, and plugs free of dust.
Lubricaon &
Mechanical
The actuator or mechanical li is maintenance free. Do not lubricate. Be
careful to avoid applicaon of scky substances to the mechanism. DO NOT
use soap and water for cleaning the liing mechanism
Leveling Feet Regularly check to ensure the table is level and stable.
See page 6 for leveling instrucons.
With proper maintenance, your table is designed to give you years of trouble-free operaon.
To ensure your table will connue to funcon properly and keep its appearance, we
recommend the following.
Cleaning & Ongoing Maintenance
DO NOT USE acetone, “Armor All” type cleaners, citrus-based cleaners,
or industrial cleaners. These can seriously damage the upholstery. Such
damage would not be covered under warranty.
RISK OF ELECTRIC SHOCK
Always unplug this furnishing from the electrical outlet before cleaning.
SECTION 5: CARE & MAINTENANCE
10

SECTION 5: CARE & MAINTENANCE
This helpful troubleshoong guide will provide you with informaon about how to recognize a
problem with your table, determine possible causes, and nd a soluon.
In the event your specic situaon is not covered in this guide, please contact Living Earth Cras
so our technical support department can assist you. Beyond the troubleshoong guide below, do
not aempt to repair the table yourself. This can void your warranty.
Unauthorized service will not be covered. Please be sure to contact Living Earth Cras Customer
Service rst at [phone], [phone] Int’l.
Troubleshooting
Issue Solution
Table does not
raise or lower
1. Ensure the table is plugged in.
2. If using a dimmer switch, ensure it is turned to full power.
3. Ensure the outlet in your room is receiving power. This can be done
by plugging in a small appliance and turning it on.
4. Ensure the switch on the aached power strip is turn on.
5. Check the fuse or circuit breaker for blown fuse or tripped breaker.
6. Ensure the controls are securely plugged into the juncon box.
Warranty Information
Living Earth Cras (LEC) oers an industry best warranty against defects in materials, design,
and workmanship, to the original owner, as follows:
• Frame - limited lifeme warranty*
• Foam and upholstery covering - warranted for three (3) years
• Motors, controls, electronics - warranted for two (2) years, including parts and labor
• Accessories and opons - warranted for one (1) year, unless otherwise noted
LEC may repair or replace defecve components at our discreon. LEC will return the warranted
product, standard shipping pre-paid, to customers in the connental US. Internaonal customers
are responsible for any applicable dues and taxes, as well as all shipping charges inbound and
outbound. Normal wear and tear, and costs associated with maintenance procedures, and
damage caused by accident, misuse, improper maintenance, harsh operang environments or
neglect (which includes tears in the upholstery and damage caused by harsh chemical-based
cleaners) are not covered under this warranty. All warranes are limited to repair or replacement,
at LEC’s discreon, unless otherwise stated.
*Lifeme warranty applies to the original owner, as long as you own your table for 5 years aer
the model is disconnued, or 5 years for private label tables.
RISK OF ELECTRIC SHOCK
Always unplug this furnishing from the electrical outlet before cleaning.
11

Owner’s Record

Notes

Contact Us
Living Earth Crafts
990 Joshua Way
Vista, CA. 92081
[phone]
[phone] Int’l
[phone] fax
[email protected]
Hours of operation:
Monday - Friday
8:00 a.m. to 5 p.m. PST
Saturday - Sunday
Closed
Visit us online at: livingearthcrafts.com
Join us on
Facebook
Follow us on
Twitter
Connect with us
on Linked In
Follow us on
Instagram