Living Spaces LUCA Y2103W-340 User manual

ASSEMBLY INSTRUCTIONS
LUCA TWIN-TWIN BUNK BED
ITEM NO: Y2103W-340/341/342
Y2103B-340/341/342
Y2103G-340/341/342
SKU: 314663/314664/314665
314575/314576/314577
314619/314620/314621
1
30 min
x 2 x 1 x 1

PLEASE TAKE TIME TO READ ALL INSTRUCTIONS AND
WARNINGS BEFORE BEGINNING ASSEMBLY!
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance
with:
ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government
specifications 16 Code of Federal Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the
carton. Do not remove this label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Top surface of mattress must be at least five inches (127mm) below the upper edge of top guard
rails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their
proper position, free from damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed and ladder.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or Stairway Chest for entering and leaving the upper bunk (as page 3).
9. Do not use substitute parts. Contact Living Spaces for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper Bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall. (This applies
only to bunk beds without two full-length guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is expressly prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed
for example, but not limited to hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
- Use only mattress which is 75'' long and 37.5- 38.5” wide on upper bunk, lower bunk of Twin
bed.
- Ensure thickness of mattress does not exceed 6" and mattress is at least 5" below upper edge of
guardrails.
- Ensure thickness of mattress doest not exceed 6" for lower bunk.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be requested from Living Spaces, usually at a
cost.
2

Always use the ladder or
Stairway Chest for entering
and leaving the upper bunk.
You will buy
ladder/Stairway as options.
3

BOX 1-TW /TW + TW /FL UPPER ENDS/SLATS BUNK BED
AUpper Ends 2
Slats 1
J
BOX 2: TW /TW LOWER ENDS/SLATS BUNK BED
BLower Ends 2
Slats 1
J
4
1987TT-A-W: (White)
1987TT-A-B: (Blue)
1987TT-A-G: (Grey)
1987TT-J
1987TT-B-W:(White)
1987TT-B-B:(Blue)
1987TT-B-G:(Grey)
1987TT-J
PART SKU# IMAGE DESCRIPTION QTY
PART SKU# IMAGE DESCRIPTION QTY

BOX 3- TW /TW SIDE/GUARD RAILS BUNK BED
CUpper Rails 2
Guard rails 4
D
EGuard rail
supports 2
FLower rails 2
5
1987TT-C-W: (White)
1987TT-C-B: (Blue)
1987TT-C-G: (Grey)
1987TT-D-W: (White)
1987TT-D-B: (Blue)
1987TT-D-G: (Grey)
1987TT-E-W: (White)
1987TT-E-B: (Blue)
1987TT-E-G: (Grey)
1987TT-F-W: (White)
1987TT-F-B: (Blue)
1987TT-F-G: (Grey)
PART SKU# IMAGE DESCRIPTION QTY

Allen key 60*22*4mm
1
2
Dowel Ø8*40mm
Screws 8#*30mm
Screws Ø6.5*83mm
Bolt and nut M8*90mm 16
6
Part IMAGE DESCRIPTION QTY
3
4
5
6
7
8
28
1
4
Metal dowel Ø10*100mm
Bolts M8*35mm
16
Hardware List of Twin-Twin Bunk Bed
SKU#
THE HARDWARE IS LOCATED IN THE PACKING ITEM
NOTE: MUST TIGHTEN SCREWS PERIODIACLLY. WITH USE SCREW MAY ENCOME
LOOSE CHECK TIGHTNESS OF ALL SCREWS EVERY 6-8 WEEKS.
CLEANING INSTRUCTIONS:
After assembly, clean and polish the completed parts if necessary with
soft cloth and industrial recognized furniture polish.
6
1987TT-1(16)
1987TT-2(6)
1987TT-3(8)
1987TT-4(16)
1987TT-5(28)
1987TT-6(4)
1987TT-7(1)
D
C
E
A
B
F
A
B
E
J
J
Detail view
Note: Screwdriver will be prepared by yourshelf.

STEP 1:
* Assembly Rail (C):
Please locate two rails (C) to Ends (A) by Dowel (4) firstly, and then fasten gradually
by Bolt+nut (1) BUT NO TIGHTEN.
* Assembly Guard Rail (D):
Please locate Guard rails (D) to Ends (A) by Dowel (4) firstly, and then fasten gradually
by Bolt (3).
A
A
D
C
C
7
3
1
4
1
1
4=12Pcs
1=8Pcs
3=8Pcs
STEP 2:
Assemble the Guard Rail Supports (E) to Upper bed frame by Bolt (2).
E
2
3
1
2=6Pcs
7
7
Pay attention to rail orientation.
Before assembly:
Move the nut out

J
5
STEP 4:
Insert dowel (4) to Ends (B) firstly, then the Rails (F) are fastened by
Bolt+nut (1).
1
F
B
B
7
1
4
5=14Pcs
4=4Pcs
1=8Pcs
8
F
STEP 3:
Please fasten slats (J ) by screw (5) into corresponding holes.
1
1
Pay attention to rail orientation.

STEP 6:
Assemble the
upper bunk to
lower bunk by
Metal dowel (6).
5
J
6
6=4Pcs
5=14Pcs
9
STEP 5:
Please fasten slats (J ) by screw (5) into corresponding holes.

Combining with Ladder ( Option 1)
Attaching the ladder to Guard rail by Screw (this hardware is placed in ladder box)
10