Living Spaces reive REV2500 User manual

Patent Pending
Warranty - 2-Year Parts and Labor on entire base
by LIVING SPACES
REV2500 Wireless Adjustable Base
OWNER’S MANUAL
Installation & Operation

Safety & Warranty Warnings 01
Parts List 04
REV2500 Electronics Quick Reference Guide 05
Installaon Guide 07
REV2500 Remote Control Instrucons 09
Bluetooth Intrucons 11
Seng Programmable Posions and Pairing Remote 12
Seng Preset posions 13
Emergency Baery Backup 14
Synchronizing Two Bases 16
Headboard Bracket Installaon Guide 17
Troubleshoong 18
CONTENTS

Safety & Warranty Warnings
A: READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
If unable to understand warnings, cauons, and/or instrucons, contact the dealer or technical personnel if applicable, before aempng to
use the equipment. Otherwise, injury or damage may result.
SAFETY WARNINGS:
• Do not use bed outdoors.
• Do not use bed near explosives.
• Using bed with oxygen administering equipment other than the
nasal masked type creates a possible fire hazard.
• When using nasal or masked type administering equipment, route and secure oxygen or air tubing properly to ensure that tubing does not
become entangled or damaged during normal operaon of the bed.
• Use cauon when having liquids in or around the bed to ensure no spilling occurs. In case of spillage, stand in a dry,clean area of the floor
and unplug the bed immediately. Clean up spill and allow the area around bed to dry thoroughly before using the electric controls again. Do
not eat or drink hot liquids while operang the bed.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilies, or lack of
experience and knowledge, unless they have been given supervision or instrucons concerning use of the appliance by a person
responsible for their safety.
• Do not allow children or individuals with disabilies to operate the bed without adult supervision.
• Do not allow any person or pet under the bed at any me.
• During bed operaon, make sure body is posioned within the confines of the bed. Do not place extremies over the sides of the bed
when operang bed funcons.
-01-

WARRANTY WARNING!
Do not open or tamper with control box, motors, or remote (with the excepon of baery compartments). The warranty will be void if the
internal workings of these components are tampered with.
Product Rang:
The motors are not designed to operate connuously for more than [2] minutes in an [18] minute me period or approximately 10% duty
cycle. Aempng to circumvent or exceed this rang will shorten the life expectancy of the foundaon and may void the warranty. Operang
Informaon:
• Aer power foundaon assembly is completed, operate remote control to ensure proper funcons.
• Keep moving parts free of obstrucon during bed operaon (including sheets, clothing, tubing, wiring, and products using electric power
cords).
• Distribute body weight evenly over bed surface. Do not place enre weight on head or foot secons of the bed, during reposioning and
entering or exing bed.
Hospital Use Disclaimer:
This power foundaon is designed for residenal use only. It is not approved for hospital use and does not comply with hospital standards.
Weight Limits:
This product is not rated to support weights in excess of 850 pounds inclusive of the maress and bedding. The bed will structurally support
this weight, provided it is evenly distributed across the foundaon. The power foundaon is not designed to support or li this amount in
the head or foot secons alone. Exceeding this weight restricon could damage the bed and/or cause injury and will void the warranty.
-02-

RADIO FREQUENCY:2.4 GHz
FCC COMPLIANCE:
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.
To comply with the FCC RF exposure requirements, no change to the antenna or the device is permied. Any change to the antenna or the
device could result in the device exceeding the RF exposure requirement and void user’s right to operate the device.
-03-

All electronics and components that need to be installed are located in boxes under the foundaon or
aached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.
Actual product appearance and
funconality may vary from photographs.
(2) 9-Volt Baeries
Socket and Crescent Wrench
AAA Baeries (3)
A
Bed Legs & Boom Caps (6)
B C
D
Remote Control (1)
E
Retainer Bar (2)
Aached to the bed frame
F
Parts List
-04-
Power Supply (1)
& Power Cord (1)
Splier Cable(1)

REV2500 Electronics Quick Reference Guide
-05-
Control Box Foot Motor
Head Motor

-06-
Remote
Power Supply
Foot Motor
Power Cord Pairing Buon
Head Motor

Installation Guide
-07-
Two people are required to set up the foundaon.
1. Open the shipping box, cut the ribbon securing accessory
boxes & maress retainer bar, and put them aside.
Li the folded bed frame unit out of the shipping carton
carefully, and then put it on a flat floor.
2. To install all six legs (see image A on the boom right), thread
the bolt of the leg to the nut on the foundaon frame, and ghten
by hand. DO NOT OVERTIGHTEN.
carton while the bed is in the at posion.
3. Uncoil the input power cord (connected to the control box’s
power port) and plug it into the power supply.
4. Uncoil the power cord and connect it to the power supply.
Nut on the frame is removable
and replaceable.
Please remove tape on the nut
to install legs.
WARNING

-08-
Head
Leg Posions
Foot
A
6. Ensure that baeries are correctly installed.
5. Carefully flip the foundaon over onto its legs.
Important: Two people are required to move the foundaon.
Do not drag across the floor. Do not rest frame on its side;
excessive pressure may damage the legs.
7. Insert the maress retainer bars into the grommets as shown.

REV2500 Remote Control Instructions
-09-
TV preset posion
Lis and Lowers Head Lis and Lowers Foot
Memory Posion
An Snore Preset Posion
Flat Buon
Lis Head & Foot Lowers Head & Foot
Zero-G Preset Posion
Lounge Preset Posion

-10-
Memory Posion
TV preset posion
Lounge Preset Posion
ONE TOUCH BUTTONS
The double arrows li and
lower the head & foot secon of
the base.
ADJUST
Lis and Lowers Foot
Lis and Lowers Head
An Snore Preset Posion
Flat Buon
Zero-G Preset Posion

-11-
Bluetooth Intructions
Step 1: Plug base into power source
Step 2: Turn Bluetooth on in cell phone
Step 3: Install the APP
Step 4: Control device via Revive APP.
NOTE:
If you want to re-set positions,adjust the head or
foot to your desired position, then press the of
TV/ZG/Anti-Snore/M until you hear 2 beeps sound.
Now, the new positions are saved.
Opon 1)
Go to APP Store (IOS SYSTEM)/ Google Store (ANDROID SYSTEM)
Type “Revive Control” into search field and select APP,
press “install” to install APP onto cell phone as shown below.
1) Open Revive APP that was previously installed
on cell phone as shown in picture below.
Step 5: Open control center and select desired opons.
2) Click the and refresh list,then select the control box code
of your base (code also found on the control box affixed to
your base), as shown in the picture below.
3) Refresh list and select the model of your base as shown in
picture below.

PAIRING REMOTE
STEP 1
Make sure the baeries work fine.
Replace them when needed.
STEP 2
Plug the power cord to the power source.
The original remote that comes in the box is already paired to the
foundaon. No further acon is required.
In the event that the remote is not paired with the foundaon, follow
the steps below.
STEP 3
Press and hold head li and foot li simultaneously, then press and hold
the buon on the cord of control box for 3 seconds unl your hear 2
beeps sound, the remote is then paired.
Pairing Button
-12-
STEP 3
Setting Programmable Positions and Pairing Remote
SETTING PROGRAMMABLE POSITIONS
To adjust the saved posion, repeat steps 1 and 2 and the new
posion will be saved.
STEP 1
Adjust the head and foot to your desired posion.
STEP 2
Press and hold the flat buon first, then press and hold memory
buon for 5 seconds unl you hear 2 beeps sound.
The wireless power bed has a programmable feature that allows you
to save custom posions.
Please read all the instrucons below before seng your custom
presets on the remote.

-13-
STEP 3
Setting Preset positions
SETTING PRESET POSITIONS (TV, ZG, An Snore)
To adjust the saved posion, repeat steps 1 and 2 and the new posion will be saved.
STEP 4
If you want to restore to factory sengs, unplug the power supply for 5 seconds, then plug back in. The base will restore to factory
sengs.
STEP 1
Adjust the head and foot to your desired posion.
STEP 2
Press and hold the flat buon first, then press and
hold ZG or An Snore or Lounge buton for 5 seconds unl
you hear 2 beeps sound.
The wireless power bed has a programmable feature that allows you to modify preset posions.
Please read all the instrucons below before seng your preset posions on the remote.

-14-
Emergency Battery Backup
Overview
Important: The backup baery is only to be used in case of a power outage. Baeries are not to be used for normal operaon of the bed. The
backup baery will not support repeated movement for an extended period of me.
Backup Baery Use:
Use two 9V baeries only (not included). If a power outage occurs, install the 9V baeries into the power supply to allow temporary power
to the base (see image A).
Installing Baeries:
Unplug the power cord from the outlet and remove the cover from the compartment on the underside of the power supply (see image B).
Place two 9V baeries inside, close the cover and plug the power cord back into the wall outlet. The backup baery will not support
repeated movement for extended periods of me. Aer power is restored, unplug power cord, remove the baeries, then plug the power
cord back into the wall for normal use.

-15-

-16-
Synchronizing Two Bases
A B
If you have split bases, follow these instrucons to operate both sides
with one remote control in a synchronized manner.
Skip this step if you don't have split bases.
1. Make sure each remote control operates a respecve side (i.e.,
Remote A controls Base A and Remote B controls Base B).
2. Pair Remote A to Base B, then base A and base B can be simultane-
ous operated by Remote A.
3. Test moving both bases with Remote A. Remote B will no longer
funcon.
Tip: You can also set up dual controls using the included Sync Cable.
As an alternave to wirelessly synchronizing bases with your remote,
you can use the Sync Cable to synchronize two adjustable bed bases.
1. Set two bases next to each other.
2. Locate the Sync Cable Input on the Control Box of each base.
3.Plug the Sync Cable into each bases' Control Box.
4. Test the connecon by moving each base with your remote control.
Using the Remote Using the Sync Cable
A
1
3
2
B

-17-
Headboard Bracket Installation Guide
STEP 1
The headboard bracket will have 2 long slots
to accomodate any frame type. Align the
appropriate slots on the bracket with the
holes on the bed. Use bolts and nuts to
secure the bracket. Make sure the bolts are
ght.
STEP 4
You may now connect your headboard to the aachment plates using the remaining bolts and nuts to secure it to the brackets. The heads of the bolts
will face outward. Use a 1/2" (13 mm) socket and 1/2" (13 mm) wrench to ghten the bolts.
STEP 2
To put the T-Bracket 1 and
T-Bracket 2 together, you will
need (2) bolts and (2)nuts.
STEP 3
To put the T-Bracket and Headboard Bracket together,
you will need (2) bolts and (2) nuts. Slip the bolts
through the holes from T-Bracket to Headboard
Bracket with the head of bolt facing outward. Use 1/2''
(13mm) socket and 1/2'' (13mm) wrench to ghten the
bolts.
Headboard brackets are an oponal accessory and are not included.
A 1/2'' (13 mm) socket and 1/2'' (13 mm) crescent wrench are necessary to complete installaon.
HEADBOARD BRACKET COMPONENTS
(2) Headboard Brackets (2) T-Brackets 1 (2) T-Brackets 2 (16) Short Bolts (16) Nuts