Living Spaces SUMMIT DESK LOFT 7030-00480 User manual

SUMMIT DESK LOFT FRAME HARDWARE
QTY: DESCRIPTION:
20 100MM DECORATIVE HEAD LAG BOLTS
14MM ALLEN WRENCH
22" ANGLE BRACKETS BLACK
10 #6 X 1-1/4" PHIL FLAT PARTICLE BOARD SCREWS
16#8 X 3/4" PHIL PAN ZINC SCREWS
14MM ALLEN DRIVER FOR POWER DRILL
7030-00480 KIT
24" x 2" STRAIGHT BRACKETS
23" FLUTED 1/2" DOWELS

4668/4669/4678/4679
PARTS LIST:
7030-00480
A purchased ladder is optional (Sold separately). The
Tall End structure can be used as a ladder.
A) 1 - Twin Medium End Assembly
B) 1 - Twin Tall End Assembly
C) 2 - 7" x 75" Mattress Rails w/Support Cleats
D) 2 - 5" x 75" Guard Rails
E) 1 - 3" x 75" Support Rail
F) Universal Loft Desk
G) 3 - 3 1/2" x 38 1/2" Mattress Supports
HARDWARE PACKAGE INSIDE FRAME
CARTON:
20 - 100MM Decorative Head Lag Bolt
1 - 4 MM Allen Wrench
1 - 4MM Power Drill Driver
10- 1 1/4" Black Flat Head Wood Screws
2 - 2" Corner Brackets
2 - 4" x 2" Straight Brackets
16 - 3/4" Pan Head Screws
2 - 3" Fluted Dowels
TOOLS REQUIRED:
1) Phillips Head Screwdriver
NOTE: Tool recommended: Electric driver for 4 MM
Power Drill Driver
ASSEMBLY INSTRUCTIONS:
SUMMIT DESK LOFT
A
B
C
D
E
G
NOTE:
Make sure you have all parts before beginning
assembly. If you need a part, contact the dealer
where you purchased your bed.
1) Attach two mattress rails (C) , two guard rails (D), and one support rail (E) to end assemblies with 10- 100mm lag
bolts for tall twin end (B) and 10- 100mm lag bolts for medium twin end (A), and tighten.
2) Place 3 mattress supports (G) on mattress rail support cleats, with one support in the center, and a support pushed
tightly against each end assembly. If using a purchased slat kit, please see the proper support placement on the last
page of these instructions. NOTE: A foundation is required with 3 slat configuration.
3) Secure mattress supports with 6 wood screws, one on each side of support.
4) Insert the two fluted dowels into the pre-drilled holes on top of the desk (F), and place the medium twin end so that
the holes in the bottom of the posts go over the inserted dowels.
5) Secure the medium twin end to desk as pictured above, using the provided brackets and pan head screws.
6) Add a bunk board or slat kit and the proper thickness innerspring bunk mattress. SEE DEALER FOR DETAILS

00700
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance with:
ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government
specifications 16 Code of Federal Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do
not remove this label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least five inches(127mm) below the upper edge of guardrails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or bed end for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact manufacturer or dealer for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts and jump ropes.
SIZE OF UPPER AND LOWER MATTRESS AND FOUNDATION
Your Twin bed is designed to use a mattress 37”-39” in width and 74” - 75” in length.
Your Full bed is designed to use a mattress 52”-54” in width and 74” - 75” in length.
The total thickness of mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 7”.
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, maybe obtained from your Furniture dealer.
4706, 4711, 4721, 4731, 4738, 4743UPDATED: 06/08/2016
* A FOUNDATION IS REQUIRED WITH 3 SLAT CONFIGURATION *

Installation of individual slats for use with Slat Roll (Slat roll sold separately) See your retailer for purchase of Slat Roll
SCREW
SCREW
SCREW
SCREW SCREW SCREW SCREW
SCREW
SCREW
SCREW
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
Installation of individual slats for use with Bunkie Board (Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
SCREWSSCREWSSCREWSSCREWSSCREWSSCREWS
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
When used with a slat roll, the three
individual slats should be placed evenly in the gaps and underneath the strapping before fastening.
Individual Slat
Individual Slat
Individual Slat