Living Spaces ROCKPORT 20C220S-W User manual

A
A
A
B
B
B
1
1
1
C
C
C
D
D
D
E
F
G
H
1
1
10
10
10
WASHER
SEAT BOLT
ALLEN WRENCH
REF PART NAME PART IMAGE QTY REF PART NAME PART IMAGE QTY
(M6*40L)
Parts List:
PE CAP
BACK
RIGHT ARMREST
LEFT ARMREST
E
F
G
E
F
G
E
F
G
E
F
G
Assembly Steps:
Step 1: Remove protective wrapping and lay all parts on floor. Indentify all parts packed in Carton
against attached parts list to make sure all parts are presented.
Step 2:Take out the armrest (C, D) seat plate (B) and back plate (A), turn them upside down and
align the holes, as shown in the figure, use washers (E), screws (F), and PE caps (G).
Step 3: After turning the product direction as shown in the figure, use washer (E) ,screws(F),and
PE cap (G).
NOTE: IT IS USER'S RESPONSIBILITY TO MAKE SURE ALL PARTS ARE ASSEMBLED AND
TIGHTENED PROPERLY AND SECURELY.
ROCKPORT OUTDOOR 4 PIECE LOUNGE SET
20C220S-W
Assembly Instruction

A
A
B
B
1
1
1
C
C
D
D
E
E
F
F
G
G
H
1
1
12
12
12
WASHER
SEAT
BACK
ALLEN WRENCH
REF PART NAME PART IMAGE QTY REF PART NAME PART IMAGE QTY
BOLT
(M6*40L)
Parts List:
RIGHT ARMREST
LEFT ARMREST
PE CAP
A
B
C
D
E
F
G
E
F
G
E
F
G
Assembly Steps:
Step 1: Remove protective wrapping and lay all parts on floor. Indentify all parts packed in Carton
against attached parts list to make sure all parts are presented.
Step 2:Take out the armrest (C, D) seat plate (B) and back plate (A), turn them upside down and
align the holes, as shown in the figure, use washers (E), screws (F), and PE caps (G).
Step 3: After turning the product direction as shown in the figure, use washer (E) ,screws (F),and
PE cap (G).
NOTE: IT IS USER'S RESPONSIBILITY TO MAKE SURE ALL PARTS ARE ASSEMBLED AND
TIGHTENED PROPERLY AND SECURELY.
Step 2
Step 3
ROCKPORT OUTDOOR 4 PIECE LOUNGE SET
20C220S-W-D
Assembly Instruction

A
A
B
1
1
1
C
C
D
E
G
4
4
4
WASHER
DESKTOP BOLT
LEG ALLEN WRENCH
REF PART NAME PART IMAGE QTY REF PART NAME PART IMAGE QTY
(M6*20L)
Parts List:
BOTTOM PLATE
Assembly Steps:
Step 1: Remove protective wrapping and lay all parts on floor. Indentify all parts packed in Carton
against attached parts list to make sure all parts are presented.
Step 2:Take out the table top (A) and turn it upside down, and insert the table legs (C) into the
holes as shown. Make sure that the snaps are exposed in the holes.
Step 3: Take out the bottom plate (B) and align the holes as shown in the figure , use the
washer (D) ,screws (E),andPE cap (F)
NOTE: IT IS USER'S RESPONSIBILITY TO MAKE SURE ALL PARTS ARE ASSEMBLED AND
TIGHTENED PROPERLY AND SECURELY.
Step 2
ROCKPORT OUTDOOR 4 PIECE LOUNGE SET
20CT220S-W
Assembly Instruction
D
E
Step 3
C
A
B
F
4
PE CAP
F