Living Spaces Sophia II Queen Storage bed 255543 User manual

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in headboard carton to attach bed feet .
1 2
Step#1
Retrieve bed feet from carton fastened behind the headboard.
Attach bed feet (F) to the headboard .
Step#2
Attach bed feet (F) to the side rails .
F
H=10CM
4PCS
Sophia II Queen Storage bed Assembly Instructions

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in side rails carton to attach center support system..
3 4
Step#3
Attach side rails to headboard using Wrench (I), Bolt (B) and Washer (E)(factory installed).
Attach Metal support beam (U) to side rails using Wrench (I), Bolt (A1) and Washer (E).
(factory installed).
Step#4
Attach center support rail (O) to the Headboard using Wrench (I), Bolt (B) and Washer
(E).(factory installed).
Attach center support rail (O) to the Metal support beam (U) using Wrench (I), Bolt
(L) ,Washer (E) and Nut (Z). Tighten/secure center support rail with Wrench (Y) .
D
E
I
J
L
M
N
O
P
U
Y
Z
Φ6 MM
Φ8 MM
Φ8 MM
H=30
CM
Φ8*50MM
Φ6*40MM
3PCS
2PCS
1PC
3PCS
2PCS
3PCS
13PCS
1PC
26PCS
1PC
1PC
2PCS
Sophia II Queen Storage bed Assembly Instructions
*Bolt B and Washer E
are factory installed*
*Bolt A1 and Washer E
are factory installed*
*Bolt B and
Washer E are
factory installed*

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in side rails carton to attach center support system.
6 7
Step#5
Locate bed in final position before attaching center supports.
Step#6
Attach center support legs (J) to the Center support Rail (O) using Wrench (I), Bolt (M) and
Washer (D).
Attach center support leg (J) to the Metal support beam (U) using Wrench (I), Bolt (M) and
Washer (D).
Step#7
(IMPORTANT:Make sure slats are inserted into center clip BEFORE snapping into place)
Verify Euro Slats System Tension Slats are installed curved upwards per diagram.
Insert tension slats into center clip (N) and factory installed End clip (Q) before snapping
into place.
D
E
I
J
L
M
N
O
P
U
Y
Z
Φ6 MM
Φ8 MM
Φ8 MM
H=31CM
Φ8*50MM
Φ6*40MM
3PCS
2PCS
1PC
3PCS
2PCS
3PCS
13PCS
1PC
26PCS
1PC
1PC
2PCS
Sophia II Queen Storage bed Assembly Instructions
*Clip Q are factory
installed*

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in storage drawer carton.
8 9
Step#8
Attach casters (T) to the drawer using Wrench (I), Bolt (A) and Washer (D).
Step#9
Attach drawers to the footboard using Wrench (I), Bolt (B) and Washer (E).
Drawers attach 3/4" below bottom of footboard.
A
D
I
T
Φ6*15MM
Φ6 MM
Φ8 MM
H=8 CM
16PCS
16PCS
1PC
8PCS
Sophia II Queen Storage bed Assembly Instructions

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
10
Step#10
Insert/Roll the drawer under the bed.
Factory installed guide rail keeps drawer centered.
Sophia II Queen Storage bed Assembly Instructions
*Factory installed guide rail keeps drawer centered*