Living Spaces Sedona Junior Loft 7030-01260 KIT User manual

Sedona Collection: Junior Loft
PARTS LIST
BOX 1: 4137 Sedona Junior Loft Ends
Part # Description Quantity
S0021END Junior Loft Bed End 2
BOX 2: 4136 Sedona Junior Loft Frame
Part # Description Quantity
S0001SRL 5/4x6 Mattress Rail 2
541750001 5/4x4 Guard Rail 4
560750001 5/4x6 Support Rail
1
149383/40 Individual Twin Slat 3
5040-43181 Hex Lag Bolt/Washer 28
5040-35410 #6 x 1 1/4 Phil Flat Slat Screw 10
Picture
Picture
7030-01260 KIT
For: 4136 Frame Rails/4137 Loft Ends
COMPLETED ASSEMBLY

1) Attach the one support rail (560750001) to the bottom of the end assemblies
(S0021END) with 4 lag bolts and 4 washers (5040-43181), and tighten.
2) Attach two mattress rails (S0001SRL) and four guard rails (541750001) to the top of the
end assemblies with 24 lag bolts and 24 washers (5040-43181), and tighten.
3) Lay out your slat kit on the bed surface, resting on the mattress rail cleats, and place the 3
individual slats (149383/40) in accordance with the diagram on the last page of these
instructions. Attach the 5 designated slats to the mattress rail cleats using the #6 x 1
¼”screws (5040-35410).
5040-43181
S0021END
560750001
541750001
S0001SRL

Optional Setup
BOX 1: 4492 Sedona Super Storage Dresser
Part # Description Quantity
4492 Sedona Super Storage Dresser
1
BOX 2: 4493 Sedona Stairway Chest
Part # Description Quantity
4493 Sedona Stairway Chest
1
Picture
Picture
One or both of the above optional pieces can be purchased to accentuate the
Sedona Junior Loft as pictured below:

00500
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance with:
ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government
specifications 16 Code of Federal Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do
not remove this label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
of entrapment or falls.
3. Top surface of mattress must be at least five inches (127mm) below the upper edge of top guard rails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed and ladder.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or bed end for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Living Spaces for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is expressly prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Your Twin bed is designed to use a mattress 37”-39” in width and 74” - 75” in length.
Your Full bed is designed to use a mattress 52”- 54” in width and 74” - 75” in length.
The total thickness of mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 10”.
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be requested from Living Spaces, usually at a cost.

Installation of individual slats for use with Slat Roll (Slat roll sold separately) See your retailer for purchase of Slat Roll
SCREW
SCREW
SCREW
SCREW SCREW SCREW SCREW
SCREW
SCREW
SCREW
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
Installation of individual slats for use with Bunkie Board (Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
SCREWSSCREWSSCREWSSCREWSSCREWSSCREWS
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
When used with a slat roll, the three
individual slats should be placed evenly in the gaps and underneath the strapping before fastening.
Individual Slat
Individual Slat
Individual Slat
Diagram 1 Diagram 2
Scan Code for Instructional video

Sedona Collection: Knob Installation
7030-01195 KIT
1. Locate the box containing your knobs in the bottom drawer of your case good.
2. Identify which of the screw sizes is correct for your drawers/doors. The screw should
protrude no more than 1/4" when pushed through the pre-drilled holes on your
drawers/doors.
3. Push the screw through the back of the pre-drilled hole on the drawer/door and line it
up with the thread on the back of the knob.
4. Tighten the screw into the back of the knob until the knob is tight against the front of
your drawer/door.
**You can tighten your screws with either a phillips screwrdiver,
a drill with a phillips bit, or your hand**
(Scan code for
instructional
video)