LK Heat Cutter 90 W User manual

1 (2)
Operation using LK Heat Cutter 90 W
Ensure working areas are well ventilated and
wear a protective mask; the fumes that are crea-
ted can be health hazardous.
Do not cut PVC and PVC-coated materials, the
toxic fumes are hazardous. Take care when using
the tool to prevent accidental burns and res.
The blade may reach 600°C / 1100°F. Never touch
the blade when the power switch is pushed. Do
not place the tool against any surface after usage
until the blades have cooled down. Do not use
the product in unsuitable environments.
Unsuitable environments are:
• Wet areas or in high air humidity.
• Dust and ammable gases, fumes or sol-
vents.
• Strong vibrations.
Always unplug the device when not in use.
Design
LK Heat Cutter 90 W is an electric heated tool for
cutting pipe grooves in LK Slotted Board and LK
Turning Board EPS 30/50/70. The heat cutter can
be supplemented with additional groove blades
and/or knife blades. The tool works by heating
the groove blade to melt/carve pipe grooves in
EPS-Styrofoam insulation boards.
LK Groove blades are available in dimensions
16, 25 and 32-34. The size range accommodates
16mm pipe and two sizes of conduit.
LK Knife Blade 40 is available as an accessory
for cutting EPS boards up to 50 mm. As the bla-
de cannot cut through thicknesses over 40 mm,
an initial straight cut is made, the board is then
snapped off.
LK Knife Blade and LK Groove Blade.
LK Turning template EPS
To facilitate tracking at turning pipes, LK Turning
template EPS is avaliable. See accessories.
LK Heat Cutter 90 W
EN.33.C.125.1606
Assembly instructions | LK Heat Cutter 90 W

2 (2)
EN.33.C.125.1606
Assembly instructions | LK Heat Cutter 90 W
Technical data
Article no. 241 99 36
Operating voltage 230 V~ 50–60 Hz
Power consumption 90 W
Illumination 6 V – 1,2 W BA7s (2 pcs.)
Intermittent operation 1/4 min. (12 s ON/48 s OFF)
Accessories:
LK Groove Blade 16 Article no. 241 99 38
LK Groove Blade 25 Article no. 241 99 39
LK Groove Blade 32-34 Article no. 241 99 40
LK Knife Blade 40 Article no. 241 99 37
LK Turning template, c/c 200 mm Article no. 241 95 55
LK Turning template, c/c 300 mm Article no. 241 95 56
Unless otherwise agreed, the warranty for this
device (except for blades) is one year from date
of purchase. The warranty covers material and
manufacturing defects. The warranty is void if
device is used improperly, dismantled, repaired
or altered by the owner or unauthorized third
party.
This device fulls the requirements of the EU-
Directives:
2014/30/EU ”EMC-Directive”
2014/35/EU ”Low Voltage Directive”
Waste disposal
The device shall not be disposed in household
waste. An unusable device must be submitted to
approved collection/recycling points for electro-
nics.
Safety instructions
Observe the safety instructions at all time
Unauthorized changes and/or modications of
the product are prohibited for safety reasons and
due to CE approval.
The connection cable can only be replaced only
by the manufacturer or a servicing agent appro-
ved by the manufacturer with access to speciali-
zed tools.
The structure of the heat cutter complies with the
safety class II. Make sure that the insulation of the
housing is neither damaged nor destroyed.
Operation
1. Unscrew the xing screws.
2. Insert the groove or knife blade.
3. Tighten the xing screws carefully.
4. Before plugging the device in, check that the
voltage in the socket corresponds to the vol-
tage indicated on the label on the heat cutter.
5. The blade heats up when pushing the po-
wer switch. Cutting temperature is reached
in 6-8 seconds.
6. Release the power switch on the heat cutter
after end of operation.
Cutting grooves in EPS-Styrofoam insulation boards using
LK Heat Cutter 90 W.
NOTE!
Do not hold down the power switch for extended periods;
this will result in abnormally high blade temperatures.
Allow the blade to cool down occasionally during opera-
tion. The indication “intermittent operation 1/4 min. (12s)”
means: The tool is not designed for continuous operation.
After 12 seconds of heating operation, the device shall
cool for 48 seconds.
LK Systems AB, Box 66, 161 26 Bromma, Sweden | www.lksystems.se