LNS FOX WS 2 170 Manual

YOUR ”ONE-STOP-SHOP”
FOR MACHINE-TOOL PERIPHERALS
LNS America, Inc.
4621 East Tech Drive
Cincinnati, Ohio 45245 / USA
[phone]
[e-mail]
www.LNSamerica.com
INSTRUCTION AND INSTALLATION MANUAL
FOX WS 2 170 / 330 / 700 / 1020 / 1250
F190054000 WS2.13.ANG

SERIES WS 2 –F190054000
V1.3
CONTENTS
CHAPTER 1: GENERAL INFORMATION...............................................1-1
1. CONTENTS AND CONVENTIONS....................................................................................... 1-2
2. SYMBOLS AND TERMINOLOGY ........................................................................................ 1-2
3. RIGHTS ................................................................................................................................. 1-2
4. WARRANTY.......................................................................................................................... 1-3
5. SAFETY PRESCRIPTIONS .................................................................................................. 1-4
6. SAFETY ANALYSIS FOR CORRECT INSTALLATION ...................................................... 1-5
7. MAIN SAFETY REGULATIONS ........................................................................................... 1-5
8. INFORMATION LABEL DESCRIPTION AND PLACEMENT .............................................. 1-6
9. UNIT RANGE OF USE.......................................................................................................... 1-7
CHAPTER 2: TECHNICAL DATA / TRANSPORT..................................2-1
1. IDENTIFICATION AND TECHNICAL SPECIFICATIONS.................................................... 2-2
2. HANDLING AND TRANSPORT............................................................................................ 2-3
3. GENERAL SPECIFICATIONS.............................................................................................. 2-4
4. CURVE CHARACTERISTICS............................................................................................... 2-4
5. ELECTRICAL SPECIFICATION ........................................................................................... 2-4
6. DIMENSIONS ........................................................................................................................ 2-5
CHAPTER 3: GENERAL DESCRIPTION................................................3-1
1. EQUIPMENT DESCRIPTION AND COMPONENTS............................................................ 3-2
2. COMPONENT DESCRIPTION.............................................................................................. 3-3
CHAPTER 4: INSTALLATION AND USE ...............................................4-1
1. INSTALLATION..................................................................................................................... 4-2
2. UNIT INSTALLATION POINT............................................................................................... 4-3
3. UNIT INSTALLATION........................................................................................................... 4-4
4. EXTRACTION AND DISCHARGE DUCTING ...................................................................... 4-5
5. ELECTRICAL CONNECTIONS .......................................................................................... 4-13
6. UNIT USE ............................................................................................................................ 4-16
CHAPTER 5: MAINTENANCE................................................................5-1
1. INFORMATION...................................................................................................................... 5-2
2. MAINTENANCE CHART....................................................................................................... 5-2
3. ROUTINE MAINTENANCE................................................................................................... 5-3
4. EXTRAORDINARY MAINTENANCE.................................................................................... 5-7
5. TORQUE SETTINGS........................................................................................................... 5-11
6. PERIODIC CHECKS ........................................................................................................... 5-11
CHAPTER 6: TROUBLESHOOTING ......................................................6-1
1. TROUBLESHOOTING .......................................................................................................... 6-2
2. DISPOSAL AND SCRAPPING ............................................................................................. 6-4

SERIES WS 2- F190054000
CHAPTER 7: SPARE PARTS.................................................................7-1
1. SPARE PARTS......................................................................................................................7-2
2. SPARE FILTER KITS............................................................................................................7-2
3. COMPLETE SPARE PARTS LIST........................................................................................7-3

CHAPTER 1: GENERAL INFORMATION 1-1
SERIES WS 2 - F190054000
CHAPTER 1:
GENERAL INFORMATION

1-2 CHAPTER 1: GENERAL INFORMATION
SERIES WS 2- F190054000
1. CONTENTS AND CONVENTIONS
This manual contains all the indications and suggestions necessary for the installation, use and
maintenance of WS 2 series air purifiers.
2. SYMBOLS AND TERMINOLOGY
Regulations on Personal Safety
Partial or total non-compliance with these regulations may pose a serious hazard
to the safety or health of exposed persons.
Regulations on Equipment integrity
Partial or total non-compliance with these prescriptions may result in damage to
the unit and/or other machines connected to it.
Other indications and Notes of particular importance
Notes of particular importance that are not included in the two previous
classifications.
This symbol calls attention to points concerning environment protection.
3. RIGHTS
All rights reserved. The reproduction, registration or disclosure, full or partial, of this Manual in any format
and with any means, whether mechanical, photographic, acoustic or other, without LNS written
authorisation is prohibited. LNS cannot be held liable for any errors in this manual nor for any problems
that may arise.
LNS and its branches cannot be held liable for any claims, losses, costs or damages sustained or
incurred by the purchaser of this product or third parties due to accidents, poor use, abuse or resulting
from alterations, repairs or transformations not authorised by LNS.
LNS and its branches cannot be held liable for any damages and problems due to the use of accessories
and products other than those supplied or approved by LNS.
The product names indicated in this manual are registered trademarks.
The information contained in this manual are provided by way of example and are not binding in any way.
LNS reserves the right to change this information without prior notice.

CHAPTER 1: GENERAL INFORMATION 1-3
SERIES WS 2 - F190054000
4. WARRANTY
The LNS supplier guarantees its products to be free of defects that may hinder normal use for a period of
365 days starting from the date of installation which, unless otherwise stipulated between the parties,
must not take place more than sixty days from the delivery date.
The warranty is ex works and, upon discretion of the supplier, is limited to repair or total replacement of
products that prove to be objectively defective or unsuitable for the use for which they were designed.
The buyer undertakes to communicate any irregularity found within 7 days to the supplier and to make the
product deemed defective available to the supplier. In order to prevent further damage, or upon specific
request from the supplier, the buyer undertakes to not use the unit from the moment the irregularity is
found.
Failure to communicate the irregularity within the indicated time or further damage to the unit caused by
use may, upon the supplier's discretion, reduce or entirely void the warranty.
The warranty is ex the supplier's factory or ex works unless otherwise specified by the supplier.
In the event of repair work done on the customer's premises, the warranty does not cover the costs of
meals, accommodations and travel.
The warranty does not cover all imperfections or defects attributable to specific requests, material or
immaterial by the buyer or other persons acting in name of and on behalf of the buyer himself.
The warranty does not cover damage due to improper or non-compliant use of the unit, including
improper use or use not covered by the technical manual that accompanies the product.
Attempts to repair the unit by external personnel or personnel not directly commissioned by LNS will
reduce or entirely void the warranty.
Except in the event of wilful misconduct or gross negligence attributable to LNS, compensation cannot
exceed the value of the product that caused the damage.
FOX is not liable for damages caused by failed or delayed productions due to unit malfunction or
breakdown.

1-4 CHAPTER 1: GENERAL INFORMATION
SERIES WS 2- F190054000
5. SAFETY PRESCRIPTIONS
Only those individuals who know the product and are sufficiently qualified, can install, maintain
and, where necessary, repair the product. The customer must provide the resources for internal
monitoring, instructions for maintenance, work organisation, personnel training and availability of
installation and use instructions.
All individuals who work on this machine, must have read and understood the instructions in this
manual. LNS cannot be held liable for any accidents or damages to property due to failure to
follow the safety instructions.
Do not use the equipment without having
first read the safety rules and instructions for
use.
Do not allow unskilled personnel, minors or
individuals under the influence of drugs or
alcohol to use the equipment.
Loose clothing, long hair and jewellery may
be dangerous.
Do not remove guards when the equipment
is running.
Do not grasp moving or rotating objects or
other objects near them.
If certain guards must be removed for
maintenance, they must be reassembled at
the end of maintenance.
Performing maintenance inside the
switchboard when the equipment is live is
prohibited.
Bridging or removing switches, main
switches and, above all, safety switches is
strictly prohibited.
When moving, be careful not to collide with
the equipment to avoid damages.
Do not move the equipment when live.
Only use the foreseen hooking points to lift
and handle the machine to avoid personal
injuries or property damages. No one should
be near suspended load nor within the
crane, forklift or other lifting and handling
vehicle range of action.
The work area around the machine must
always be free of obstacles and well lit. Oil
on the floor could cause falls. It is important
to frequently clean the floor.
Do not install the equipment in humid
environments. Prevent water or oil from
coming into contact with electrical
equipment.
Only use components supplied or
recommended by LNS for equipment use
and maintenance.
If the machine must be moved after first
start-up, do not re-install without having first
consulted LNS or its local representative.
LNS cannot be held liable for any accidents
or damages to property due to failure to
follow the safety instructions.
Before operating the unit described below, we ask that you carefully read this manual, paying particular
attention to all the Regulations on personal safety and unit integrity
This unit was designed and produced in compliance with the following European Community safety
directives:
Machine directive 2006/42/EC
Low voltage directive 2006/95/EC
Electromagnetic compatibility directive 2004/108/EC
In compliance with the safety directives, each residual risk identified during the risk analysis has been
inserted and highlighted in this document. Specific hazard and/or warning labels have been placed on the
unit for additional safety.

CHAPTER 1: GENERAL INFORMATION 1-5
SERIES WS 2 - F190054000
6. SAFETY ANALYSIS FOR CORRECT INSTALLATION
Consider the following points before installing the machine:
Consider the safety procedures that reduce the risk to an acceptable level;
Define the fields of application and use and assess what is needed for correct use and/or
approach;
Identify the potential risk sources, including the possible malfunctions and incorrect use
associated with each possible use. Risks could be due to:
oThe machine tool in which WS 2 is integrated;
oits interface with other equipment,
ooperator interaction with the machine
Assessment of risks associated with WS 2 :
oprogramming risks
ooperating risks
ouse risks
omaintenance risks
Protection method selection:
ouse of protection devices
oapplication of signs
oobservance of safety procedures
7. MAIN SAFETY REGULATIONS
1) Consult this instruction manual thoroughly before installing, using or servicing the unit
2) Make sure the unit is isolated from the power supply (see maintenance chapter) before servicing it
3) Wear suitable protective (accident-prevention) clothing during installation and maintenance.

1-6 CHAPTER 1: GENERAL INFORMATION
SERIES WS 2- F190054000
8. INFORMATION LABEL DESCRIPTION AND PLACEMENT
A
Label that emphasises the importance of reading the
instruction manual where the main safety warnings on electric
and mechanical risks can be found.
B
Serial number label which, in addition to identifying the
machine, contains data on: weight, power, electric current
draw and air flow rate.
C
Label with filtration data for the main filter cartridge
D
Label indicating the impeller rotation direction
E
Label describing codes for original equipment filters installed
on the unit
F
Label with description of drainage trap specifications to be
installed on the drainage tube
8.1. Main label position
F
Front view
Rear view
Overhead View
(main filter)
Front view
(open)