LOCKEY USA 1150 User manual

1150 & 1600
INSTALLATION INSTRUCTIONS
No. Part Name # Included
1 Outside Body 1
2 Inside Body 1
3 Rubber Trim Plate 2
4 Adjustable Latch 1
5 Strike Plate 1
6Morsed Striker 1
7 Spindle 1
8 Support Pin 1
9 Tapping Screws 4
10 M5 x 55m Screws 4
11 M5 x 45mm Screws 4
12 Tweezers 1
13 Red “Code” Tumblers 1
14 Blue “Non-Code” Tumblers 2
1. Use the template provided and conrm the back set on the surface and the reverse side.
2. Decide the posion for the lock and mark holes as instructed by template. Drill holes.
3. Insert the Adjustable Latch into the slot. Trace line around the Latch face and remove it.
4. Chisel unl the Adjustable Latch face is ush with the surface of the door edge.
5. Fasten Adjustable Latch with the tapping screws.
Important: Ensure the Adjustable Latch face is evenly ed.
6. Break the spindle to the correct length according to the door thickness.
7. Determine Door Handing: Right-Hand Doors – From exterior of door, hinges are on right-side
(g. 1). Le-Hand Doors – From exterior of door, hinges are on le-side (g. 2). To change hand-
ing, remove screw on back of lever, then remove plate on lever. Remove two screws from lever
handle, li lever up and switch direcon of handle. Replace screws and plate, fasten.
8. For right hand doors, install Support Pin in hole on le side of back of the Outside Body.
For le hand doors, install Support Pin in hole on the right side of the back of the Outside Body.
9. Fit Rubber Trim Plate on the backside of the Outside Body, then hold Outside Body on door,
with 4 hex bolts and Support Pin through the holes in door.
10. From inside of the door, insert Spindle through the hole in the Adjustable Latch & into hole
on backside of Outside Body.
IMPORTANT: Right hand doors: Spindle must be at a 2:00/8:00 angle from the inside of the
door (Fig. 4). Le hand doors: Spindle must be at 10:00/4:00 angle from the inside of the door.
11. Fit Rubber Trim Plate to the Inside Body and t Inside Body over the Spindle, ensuring that
Spindle angle remains correct.
12. Select Machine Screws based on door thickness and fasten them through the Inside Body.
IMPORTANT: Before closing the door, test the operaon of the lock.
From Outside of Door:
1. Press “C” buon, followed by your code.
2. Turn the handle.
3. Conrm that the latch head retracts smoothly.
From Inside of Door:
1. Turn the handle and ensure the latch retracts smoothly.
q
o
p
l
sj
k
n
r
l
m
11
12
13 14
Back of Outside Body (Fig. 3)
Support Pin Holes
View from Inside (Right Hand Door)
(Fig. 4)
Insert support pin
(Right Hand Door)
8:00
2:00
Instrucons connued on reverse

IMPORTANT: This lock is equipped with a Passage Funcon, allowing you to leave the door unlocked.
To enable passage funcon:
1. Push “C” buon to clear.
2. Enter your code number, followed by the “R” buon. Your lock is now in Passage.
To diable passage funcon:
1. Press the “R” buon followed by the “C” buon.
To permanently disable passage funcon:
1. Hold Outside Body in horizontal posion.
2. Remove the four red screws.
3. Carefully remove the plate, as there are many springs aached to it.
4. Press and hold the “C” buon from underneath.
IMPORTANT: Remain holding the “C” buon unl the tumbler is removed.
5. Remove the “R” tumbler with the Tweezers provided.
6. Replace plate and replace four red screws.
1. Hold the Outside Body in horizontal posion. Remove the four
red screws. Carefully remove the plate.
HOW TO CHANGE CODE
2. Hold the “C” buon from underneath from now unl you
have completed the code change.
FAILURE TO DO SO WILL DAMAGE THE LOCK.
While connuing to hold the “C” buon, use tweezers to
rearrange code/non-code tumblers to create desired code.
13. Close the door to determine where the Latch head touches to the face of the door jamb.
14. Chisel out the space for the Mosed Striker and for the Strike Plate so that the Strike Plate is ush with the surface of the door
jamb.
15. Fasten Morsed Striker and Strike Plate with screws.
PASSAGE FUNCTION
3. Code is made up of RED tumblers. Make sure the colored
end is facing upwards. Example: If your desired code is 13569,
red tumblers will be placed in numbers 13569 (shown below).
4. When completed changing your code, release the “C”
buon and replace the plate carefully.
5. Always test your new code before installing/re-installing
the lock to the door. Remember to press “C” buon before
entering code.
Before changing code, read this informaon carefully. FAILURE TO FOLLOW INSTRUCTIONS CAN RESULT IN DAMAGE TO LOCK.
RED TUMBLERS = CODE TUMBLERS
BLUE TUMBLERS = NONCODE
“C” TUMBLER = CLEAR (cannot be removed)
“R” TUMBLER = PASSAGE FUNCTION (instrucons above) (do NOT replace with any other tumbler)
“R” Tumbler
“C” Tumbler