LOCKEY USA GE370 User manual

INSTALLATION
INSTRUCTIONS
GE370 -
Gemini Electronic
www.lockeyusa.com/GE370
Please check that template is
correct size before use –
copies can be distorted
Cut Here
For surface mount option,use 3 x hole positions
Before drilling holes, please ensure that the
position of the lock when installed will
allow clearance for the cam to function.
Important Note:
Inserting Battery
Step 1 Remove all packaging.
Step 2
Insert Battery 1/2AA. As shown in Picture 7.
Positive facing out as per ‘ + ’ sign on inside battery case.
Step 3 Secure battery with Battery Lid as per picture 8. Click into position.
Picture 7.
Insert ½ AA Battery as shown.
Picture 7.
Fit Battery Lid as shown click in place.
IF USING A PRINTED TEMPLATE ENSURE THAT THE
TEMPLATE IS THE CORRECT SIZE AS PRINTERS VARY
Lock eyUSA
4245 S. Lincoln Rd.
Mt. Pleasa nt, MI
48858
T: 888.395.0163
F: 989.772.1936
E: info@lo ckeyu sa.c om
W:www .lockeyusa.c om
For flush fitoption,use rectangular aperture (88mm x 28mm)

INSTALLATION INSTRUCTIONS
GE370 - Gemini Electronic
•Flush Mount
•Surface Mount
Surface Mount
Step 1 Remove all packaging.
Step 2 Fit the surface mount sleeve to lock as shown in Picture 1.
Step 3 Position the lock on the outside of the door as shown in Picture 2.
Step 4 Holding the lock in position, fit the 2 x M4 pan head screws
(supplied with the surface mount sleeve) as shown in Picture 3.
Step 5 Tighten the 2 x M4 screws to 1Nm.
Step 6
Position the cam onto the rear of the lock as required, fit the cam washer
and fixing screw as shown in Picture 6.
Step 7
Tighten the cam fixing screw to 1.5Nm. Take care not to damage
the screw thread when fitting the screw.
Step 8 Before closing the door, test the lock by selecting the correct User Code
and rotating 90°.
Step 9 Your lock should now be ready to use.
Flush Mount
Step 1 Remove all packaging.
Step 2 Position the lock on the outside of the door as shown in Picture 4.
Step 3 Holding the lock in position, fit the clamp box and 2 x M4 pan head screws
(supplied with the clamp box) as shown in Picture 5.
Step 4 Tighten the 2 x M4 screws to 1Nm.
Step 5
Step 6
Step 7 Before closing the door, test the lock by selecting the correct User Code
and rotating 90°.
Step 8 Your lock should now be ready to use.
Picture 1.
Fit surface mount sleeve to lock as shown.
Picture 4.
Position lock through door panel as shown.
Picture 2.
Position lock on door panel as shown.
Picture 5.
Fit clamp box and 2 x M4 pan head screws as shown.
Picture 3.
Fit 2 x M4 pan head screws as shown.
Picture 6.
Fit cam, washer & screw. Tighten.
Special Notes
Before installing the Gemini Electronic, load the battery and familiarize
yourself with the operation and programming. The lock is supplied in PUBLIC
operating mode with a four-digit code.
The lock can be opened at any time using the Master Code.
Unless manufactured to special order, the default Master Code is 11 33 55 77
and the default User Code is 22 44. These codes are common to all standard
locks and it is very important that you set your own personal Master and User
Codes. Your lock is not secure until you have changed the default Master Code
and User Code.
Keep a safe record of your master code as it is not possible to make any
programming changes without it.
Please see programming guide to set your own codes.
The GE370 lock can be installed in two ways:
Position the cam onto the rear of the lock as required, fit the cam washer
and fixing screw as shown in Picture 6.
Tighten the cam fixing screw to 1.5Nm. Take care not to damage
the screw thread when fitting the screw.