Long Range Systems Butler II Specification sheet

Each button on the one or five button Butler II can be programmed to send a unique message
to separate pagers or group of pagers. Both the five-button and one-button models can also
send a specific message for an external switch or sensor.
Installation
To put the Butler II in operation:
Note: If your Butler II is not already programmed, refer to the programming guide first
1 Install the 3-batteries in the butler (note the + end)
2 Locate the mounting bracket where it is to be used (use screws, straps or velcro)
3 Install the batteries
4 Position the unit into the notches in the mounting bracket and press until latch en-
gages
5 Connect an external sensor (if used)
6 Turn on the pager (refer to the pager booklet)
7 Press the button(s) to test the pager
Normal Operation
1 The indicator light will be faintly blinking
2 Press a button, the indicator light will flash and the pager will receive the message
3 For external contacts, enable the contact and the pager will receive the message
Advanced Feature Operation
Enabling the following features require the programming kit. Instructions for this kit are contained
in the Help file.
Auto Off/On
The Butler II can be set to automatically turn off or on at pre-selected times of the day
Page Acknowledge
The Confirmation button will send a message indicating the time between a button press
(or other input) and staff response
Long Range Systems 1Butler II Quick Guide
Butler II
Five and One Button Paging System
QUICK SETUP & OPERATION
Long Range Systems UK Ltd | Link House | Leek Road | Milton | Stoke on Trent | Staffordshire | ST2 7AH | 01782 537000
www.lrspagers.co.uk | www.pagers.co | www.hospitalpagers.co.uk

Low Battery Page
The Butler II can send a low battery message when batteries are low
Lockout
The alarm input can be locked out (disabled) for a period of time. This allows staff to pass
through monitored areas without setting off alarms.
• The staff member presses Confirmation button simultaneously,
• Then enters a 3-digit disable code
• The alarm is disabled for a selected time and will reinitiate when the alarm con-
tacts are restored
Long Range Systems 2Butler II Quick Guide
Latch
Tie Wraps
Screws
Velcro
Battery
+ End
Battery
Door
Mounting
Notches
External
Input
Confirmation
Button
Buttons
Indicator Light
Confirmation
Button
Paging
Buttons
Indicator Light
Confirmation
Button
Paging
Buttons
Push
For
Service
Five Button One Button

WARRANTY
Long ange Systems, Inc. warrants this product against any defects that are due to faulty material or workman-
ship for a one-year period after the original date of consumer purchase. This warranty does not include damage
to the product resulting from accident, misuse or improper electrical connection. If this product should become de-
fective within the warranty period, we will repair or replace with equivalent product, free of charge. We will return
your product, transportation charges prepaid standard UPS Ground shipping mode, provided the product is shipped
prepaid
Copyright © Octo er 2004, Long Range Systems, Inc. All Rights Reserved
This document contains proprietary information of Long ange Systems, Inc. (L S) and is intended for use only by
it’s employees or customers. None of the material contained herein may be copied, reproduced, republished,
downloaded, displayed, posted, or transmitted in any form or by any means, including but not limited to, elec-
tronic, mechanical, photocopying, recording, or otherwise without the prior written permission of L S. Additional
copies of this manual may be obtained by contacting L S.
Screen displays, keyboard layouts, hardware descriptions, or software are proprietary to L S and are subject to
copyright and other intellectual property rights of L S and shall be treated in accordance with the previous para-
graph.
All attempts have been made to make the information in this document complete and accurate. L S is not re-
sponsible for any direct or indirect damages or loss of business resulting from inaccuracies or omissions. Speci-
fications and other information contained within this document are subject to change without notice.
Long ange Systems, Inc. reserves the right to make changes without further notice to any products herein. Long
ange Systems, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Long ange Systems, Inc. assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Long ange Systems, Inc. data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts.
Long ange Systems, Inc. products are not designed, intended, or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Long ange Systems, Inc.
product could create a situation where personal injury or death may occur.
Should Buyer purchase or use Long ange Systems, Inc. products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Long ange Systems, Inc. and its officers, employees, sub-
sidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable at-
torney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended
or unauthorized use, even if such claim alleges that Long ange Systems, Inc. was negligent regarding the design
or manufacture of the part, device or system.
EU DECLARATION OF CONFORMITY
We, Long ange Systems hereby declare under our sole responsibility that the Butler II paging systerm and on-site
pagers complies with the essential requirements in the European E&TTE Directive 1999/5/EC of the European
Parliament of the Council of 9 March 1999 on radio equipment and telecommunication terminal equipment and the
mutual recognition of their conformity. The following standards were utilized:
ETS 300 224: 1998 EN 301 489-2: 2002
EN61000-3-2: 1998 EN 61000-3-3: 1995
EN 60950: 1992 with A1, A2, & A3
Long Range Systems 3Butler II Quick Guide
XU-0028 012610
Long Range Systems UK Ltd | Link House | Leek Road | Milton | Stoke on Trent | Staffordshire | ST2 7AH | 01782 537000
www.lrspagers.co.uk | www.pagers.co | www.hospitalpagers.co.uk