Lopi 31 DVI Manual

Model 31 and 33 DVI
Gas Fireplace Inserts

Great Features At An Affordable Price
Introducing the DVI series of gas inserts. These gas inserts represent a new direction in gas
heating that offers you a “top-quality” gas fireplace insert at an affordable price.
Shown with Universal face, traditional logset and common brick fireback options.

Control Panel
Note: For convenience, the Main Burner switch can be located on top right side of the finish panel.
The DVI series is all about flexibility: a big, beautiful, brightly glowing fire and a simplified operating system,
while offering the same construction and glass viewing area as the top selling Lopi Model DVS GreenSmart and
Model DVL GreenSmart gas inserts. Both DVI inserts feature the split-flow Dancing-FyreTM burner with your
choice of hand-crafted logs and glowing embers or stone kit with tumbled glass floor. The IPI (electronic ignition)
gas valve provides a great fire presentation and a “green” money saving solution to home heating. For convenient
hands free operation you can also add an optional wall thermostat or remote control thermostat.
Model 31 and 33 DVI
Gas Fireplace Inserts
Features
Pilot Choice
Switch
Flame
Adjustment
Control
Optional
Blower
Control
Comfort
Control
Switch
Battery
Back-up
Main Burner
Switch
(Placed Here
when used with
inside t panels)
• Dancing-Fyre Burner with the option of realistic logs
with glowing red embers and wood-like fire or the stone
kit with three colors of tumbled glass floor - reflective
platinum, reflective bronze or cobalt blue, for a
completely different fire presentation.
• Easy Heat/Flame Adjustment with a large high-to-low
flame turndown ratio.
• Comfort Control™ that allows you to turn off the rear
burner for less heat when desired or for year-round
enjoyment of the re.
• Built-in battery backup allows continued operation of
your gas insert during power outages. Automatically
switches back to AC when the power comes back on.
• Both DVI inserts are heater rated and can be used as the
primary heat source in your home.
• LED lights automatically light up the control panel when you
lower the control door. Powered by a 9 volt battery, this
feature operates even during power outages.
• Choice of pilot ignition modes - money saving IPI Electronic
Ignition mode for instant fire when you need it or Standing
Pilot for colder climates where a heated chimney is needed
to maintain the draft for proper operation.
• Approved for installation into both zero clearance (metal)
and masonry fireplaces.
• Optional 180 CFM Convection Blower will increase the
efficiency and rate of heat transfer from the insert into your
home. The blower cannot be added after insert is installed.
• LP Conversion kit included with insert at no additional cost.

Face Options
All faces are shown with the Traditional logs and ember set.
Complete Face/Panel These faces do not require Finish Panels.
Faces These faces may require Finish Panels to complete. See Finish Panels on next page.
Discovery™
Black Paint Finish
31 DVI - SKU: 99500146
33 DVI - SKU: 99500200
31 DVI Small: 23” H x 37” W
SKU: 95100050
31 DVI Large: 29” H x 40” W
SKU: 95100051
33 DVI Small: 27” H x 40” W
SKU: 95100055
33 DVI Large: 33 1/2” H x 44” W
SKU: 95100056
31 DVI
29” H x 40 3/8” W
SKU: 95100327
33 DVI
33 1/2” H x 44” W
SKU: 95100628
Antique Gold Door Frame option
31 DVI - SKU: 99300440
33 DVI - SKU: 99300441
Antique Pewter Door Frame option
31 DVI - SKU: 99300442
33 DVI - SKU: 99300443
Black Painted Wilmington Face
with Brushed Nickel Plated
Arabesque Grill
Wilmington™
Universal Independence™ Double Door
Black Door Frame (Standard)
31 DVI - SKU: 99300464
33 DVI - SKU: 99300468
Brushed Nickel
31 DVI - SKU: 99500148
33 DVI - SKU: 99500201
Dimensions
31 DVI
25 1/2” H x 32” W
33 DVI
26” H x 35 3/4” W
Dimensions
31 DVI
25 1/2” H x 32 1/4” W
33 DVI
27” H x 36” W
Brushed Nickel Wilmington Face
with Brushed Nickel Plated
Arabesque Grill
Brushed Nickel Arabesque Grill option
A brushed nickel plated Arabesque Grill set is
available to change the look of the Wilmington face.
Switch the standard vertical grills which ship with the
face and the optional Arabesque grills any time you’d
like for different looks depending on your mood.
31 DVI - SKU: 91002185
33 DVI - SKU: 9100219 0

Common Straight Brick Herringbone Brick
Add A Fireback
As An Option
Both DVI inserts ship with
a painted black interior or
you have the option of add-
ing a realistic ceramic brick
fireback that looks like real
masonry brick. For a more
contemporary look, add the
stainless steel liner or glossy
black enamel firebacks to
add a new dimension of
depth to your insert.
Wall Thermostat
The wall thermostat provides the ability to set
the desired temperature that you would like for
the room. The fireplace will cycle on and off to
maintain your set temperature. It can be wired
up to 25 feet away from the appliance and allows
for easy hands-free convenience.
Remote Control
Adding a remote provides for
the ultimate in easy operation of
your fireplace insert. The remote
offers ON/OFF and thermostat
setting. This remote control also of-
fers a clock, fireplace timer to turn
off your insert and a childproof
lockout.
Convection Fan
This 180 CFM fan enhances and speeds up the
natural heat transfer around the insert and
directs it back into your home. The fan must be
installed at the same time of installation to avoid
additional installation cost later.
Finish Options
Finish Panels
To complete the picture after the insert is
installed in your fireplace, a set of panels
are attached to the insert to accommodate
the size variance between the insert face and
the size of your existing fireplace opening.
Insert Wiring Kit
If you do not want to run a power cord across
your hearth when using the optional fan or
remote, use optional wiring kit to hard-wire
your AC power from inside the replace.
Stainless Steel
Choose from Logset or Stones
Easily transform the overall look and appearance allowing the insert to fit a wide range of architectural styles.
The Stone kit and Driftwood Fire Art™ comes with tumbled glass media oor in three colors platinum, bronze or cobalt blue.
The Traditional log set comes with glowing embers and beautifully detailed logs.
Stone Kit with Glass Media Traditional Log Set
33 DVI - 3 Piece Panels
4” x 6” Panels = 40” W x 29” H
8” x 10” Panels = 44 3/16” W x 33 3/8” H
10” x 13” Panels = 48 3/16” W x 36 3/8” H
33 DVI - One Piece Panels
42” W x 30 1/2” H
44” W x 34”
31 DVI - 3 Piece Panels
4” x 6” Panels = 37 1/8” W x 25” H
8” x 10” Panels = 40 3/8” W x 28 7/8” H
10” x 13” Panels = 44 3/8” W x 31 7/8” H
31 DVI - One Piece Panels
38” W x 25” H
40” W x 28 1/2” H
Driftwood with Glass Media
Handmade Brick
Black Enamel

31 DVI Gas Insert
Specications and Installation
Max. Height: 40 ft.
Min. Height: 8 ft.
Max. 2 ft.
offset
Air Inlet
3” Dia.
Exhaust 3”
Dia. offset
Listings:
This appliance was listed by
OMNI Test Labs to ANSI Z21.88
- report # 028-F-73-5. The listing
label is attached to the appli-
ance near the gas control valve.
IAS (ICBO) Approval
This appliance was listed by
OMNI Test Labs - IAS # TL130.
Massachusetts
Approval
Submitted to the Massachusetts
Board of State Examiners of
Plumbers and Gas
Fitters
Minimum Clearances:
Sidewall to insert: A = 4 1/2”
Side facing: B = 4 1/2”
Top facing: C = 35”*
Mantel: D = 35”*
Extension on Hearth E = 1 1/4”
*Measured from the base of the insert.
Mantel & Top Face
Clearance:
Maximum Mantel Depth is 12”
Maximum Top Facing Depth is 3/4”
(otherwise considered a Mantel)
Sidewall
Mantel
Top Facing
A
B
C
D
E
Hearth Requirements:
A non-combustible hearth extension is not required.
However, if the heater is installed next to the oor, we
recommend a hearth to protect the flooring surface from discoloration.
Leveling
bolts
15 1/8” into
fireplace
Gas line
shutoff valve
Provided with insert
Min.
19 1/2”
Min. 26 1/2”
Fireplace Requirements:
Insert must be placed within a code-conforming masonry or tested
and listed factory-built (metal) wood burning fireplace.
Venting Requirements:
• Requires UL listed (441 or 1775) Gas Liner for
exhaust and air inlet.
• Simpson Duravent 6 5/8” to 3” & 3” Co-linear
Adapter and ashing
• Simpson Duravent High-Wind Vertical
Termination Cap
Heating Capacity:* 500-1,500 Sq. Ft. - ideal for smaller homes or zone heating a portion of your home
Maximum BTU/HR Input:** 31,000 (NG/LP) Minimum BTU/HR Input:** 10,700 (NG) 12,600 (LP)
Steady State Efficiency:** Up to 71.8% (NG) 72.6% (LP) Canadian P4 Efficency: 70% (NG) 72.35% (LP)
Dimensions: Height = 19 1/2” Width = 26 1/2” (Front), 18” (Back) Depth = 15 1/8”

33 DVI Gas Insert
Specications and Installation
Max. Height: 40 ft.
Min. Height: 8 ft.
Max. 2 ft.
offset
Air Inlet
3” Dia.
Exhaust 4”
Dia. offset
Listings:
This appliance was listed by
OMNI Test Labs to ANSI Z21.88 -
report # 028-F-72c-5. The listing
label is attached to the appli-
ance near the gas control valve.
IAS (ICBO) Approval
This appliance was listed by
OMNI Test Labs - IAS # TL130.
Massachusetts
Approval
Submitted to the Massachusetts
Board of State Examiners of
Plumbers and Gas Fitters
Minimum Clearances:
Sidewall to insert: A = 4”
Side facing: B = 4”
Top facing: C = 35 1/2”*
Mantel: D = 35 1/2”*
Extension on Hearth E = 1 1/4”
*Measured from the base of the insert.
Mantel & Top Face
Clearance:
Maximum Mantel Depth is 12”
Maximum Top Facing Depth is 3/4”
(otherwise considered a Mantel)
Sidewall
Mantel
Top Facing
A
B
C
D
E
Hearth Requirements:
A non-combustible hearth extension is not required.
However, if the heater is installed next to the oor, we
recommend a hearth to protect the flooring surface from discoloration.
Leveling
bolts
14 1/4” into
fireplace
Gas line
shutoff valve
Provided with insert
Min.
23 3/4”
Min. 31 1/2”
Fireplace Requirements:
Insert must be placed within a code-conforming masonry or tested
and listed factory-built (metal) wood burning fireplace.
Venting Requirements:
• Requires UL listed (441 or 1775) Gas Liner for
exhaust and air inlet.
• Simpson Duravent 6 5/8” to 3” & 4” Co-linear
Adapter and ashing
• Simpson Duravent High-Wind Vertical
Termination Cap
Heating Capacity:* 600 to 2,000†Sq. Ft. (†with optional fan)
Maximum BTU/HR Input:** 40,000 (NG/LP) Minimum BTU/HR Input:** 11,900 (NG) - 7,400 (LP)
Steady State Efficiency:** Up to 84% (NG) - 86% (LP) Canadian P4 Efficency: 71% (NG) 70.23% (LP)
Dimensions: Height = 23 3/4” Width = 31 1/2” (Front), 20” (Back) Depth = 14 1/2”

Photos and illustrations are for descriptive purposes only. We reserve the right to improve or change our products without prior notication.
Dancing-Fyre™ and all other trademarks belong to Travis Industries, inc. Consult the Owner’s Manual for complete installation requirements.
© Copyright T. I. 2011/10 Printed in the U. S. A. 98800142
Your Authorized Lopi
Dealer Is Located At:
Lopi produces a wide variety of quality wood, pellet, gas and electric hearth products and
the award winning Tempest Torch outdoor and table top gas lamp.
Ask your Lopi dealer for details.
Find your favorite fire today by visiting www.lopistoves.com
Lopi products are made
in the U.S.A. with pride.
Only the most professional specialty hearth retailers are selected to sell Lopi stoves, inserts and
fireplaces. They represent our total commitment to exceptional products and excellent service.
In addition, they have successfully completed special training programs in the proper selection,
installation and service of all Lopi products.
Your professional Lopi hearth dealers are experts who can advise you on everything from
customizing the color of your appliance to selecting appropriate venting and chimney materials.
They can show you Lopi models on display, including working models actually burning.