Lopi ProBuilder 24 CleanFace GSR2 User manual

ProBuilder 24
CleanFace
GSR2 Fireplace
Listed By
AS/NZS 5263.1.3
GMK10026
IAPMO-R&T OCEANA
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or loss of life.
 DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
 DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
 DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
 DO NOT MODIFY THIS APPLIANCE.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
This appliance may be installed in
an aftermarket permanently
located, manufactured home (USA
only) or mobile home, where not
prohibited by local codes.
This appliance is only for use
with the type(s) of gas indicated
on the rating plate. A conversion
kit is supplied with the appliance.
Operation Manual
Installer: After installation give this manual to the home-
owner and explain operation of this heater.
 Copyright 2020, T.I. $10.00 100-01529 5/3/21
Dragon Wholesaling Pty. Ltd.
Unit 4, 16 Lexington Drive
Bella Vista NSW
Australia 2153

2 Table of Contents
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Introduction
We welcome you as a new owner of a ProBuilder GSR2 gas fireplace. This manual details operation and
maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your
heater and save the manual for future reference.
Important Information
No other ProBuilder gas fireplace has the same serial
number as yours. The serial number is on the listing
label that is chained to the gas control valve. This
serial number may be needed in case you require
service.
Model: ProBuilder 24 CF GSR2
Serial Number:
Purchase Date:
Purchased From:
Installation Warnings
 Installation requirements are printed in the ProBuilder GSR2 Installation Manual. All
requirements in the installation manual must be met.
 Failure to follow all of the requirements may result in property damage, bodily injury,
or even death.
 This heater must be installed by a qualified installer who has gone through a training
program for the installation of direct vent gas appliances.
 This appliance must be installed in accordance with all local codes if any; if not,
follow ANSI Z223.1 and NFPA 54(88). In Australia follow AS/NZS 5601.1.
 In Manufactured or Mobile Homes must conform with Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard
is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1. This appliance may be installed in Manufactured Housing only after the
home is site located.
 The fireplace is designed to operate on natural gas, or propane (LP).
 All exhaust gases must be vented outside the structure of the living area.
Combustion air is drawn from outside the living-area structure.
 Notify your insurance company before hooking up this fireplace.
 Do not place articles on or against this appliance.
 Do not use or store flammable materials near this appliance.
 Do not spray aerosols in the vicinity of this appliance while it is in operation.
 Do not modify this appliance
 Servicing shall be carried out only by authorized personnel.

Introduction 3
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Table of Contents
Introduction ................................................... 2
Important Information ................................... 2
Installation Warnings .................................... 2
Table of Contents .......................................... 3
Features ......................................................... 3
Heating Specifications .................................. 3
Before You Begin .......................................... 6
Remote Control Warnings .................................... 6
Remote Set-Up ............................................... 7
Verify the Switch is on “REMOTE” ...................... 7
Synchronize the Transmitter to the IFC ............... 7
Clearing the System Memory ............................... 7
Location of Controls ..................................... 8
Direct Operation ............................................ 8
Starting the Fireplace for the First Time ..... 9
Pilot Fuel Conservation Timer ..................... 9
Remote Operation ....................................... 10
Display Overview............................................. 10
Listen for the “Beep” ...................................... 10
Manual On-Off / Smart Thermostat /
Standard Thermostat .................................. 11
Mode Controls (Flame, Blower, EmberBed
Light)............................................................. 12
Flame Height ....................................................... 12
Blower Speed ..................................................... 12
Mode Controls - continued ......................... 13
EmberBed Light (AUX) ......................................... 13
Display Fahrenheit or Celsius .................... 13
Low Battery Indicator.................................. 13
Transmitter Batteries ...................................... 13
IFC Batteries .................................................... 13
Battery Replacement .................................. 14
Opening the Battery Box ................................ 14
Battery Installation .......................................... 14
Transmitter Battery Installation ..................... 14
Child-Proof Feature .................................... 14
Normal Operating Odors ............................ 15
Power Outages ............................................ 15
Glass Frame Removal and Installation ..... 15
Glass Removal ............................................ 17
PB 24 CleanFace - Log Installation ........... 19
Installation Warnings ......................................... 19
Log Set Overview – Oak 94500620 ................ 19
Ember bed Glass and Ember Material
Installation ................................................... 26
Ember bed Glass Installation ............................ 26
Ember Material Installation ................................ 27
Ember Installation.............................................. 27
Rock Wool Placement (All Models) ................... 27
Maintaining Your Heater's Appearance .... 28
Cleaning The Glass .............................................. 28
Cleaning the Fireplace ......................................... 28
Bulb Replacement ....................................... 29
Yearly Service Procedure ........................... 30
Troubleshooting Table ............................... 31
Replacement Parts List .............................. 32
Wiring Diagram ........................................... 33
Safety Label ...................................................... 34
CONDITIONS & EXCLUSIONS ................... 35
IF WARRANTY SERVICE IS NEEDED: ...... 35
Index ............................................................. 36
Features
 Works During Power Outages
 Contemporary Look
 Remote Thermostat
 Standing or Intermittent (GreenSmart) Pilot
 Variable-Rate Heat Output
 Low Maintenance
Heating Specifications
Natural Gas Propane
ProBuilder
24 CF
Approximate Heating Capacity (in square meters)* Up to 70 Up to 70
Maximum Input Per Hour (MJ/H) 19.89 18.5
* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
IF YOU SMELL GAS:
* Do not light any appliance
* Extinguish any open flame
* Do not touch any electrical switch or plug or unplug anything
* Open windows and vacate building
* Call gas supplier from neighbor's house, if not reached, call fire department
This unit must be installed by a qualified installer to prevent the possibility of an explosion.
Your dealer will know the requirements in your area and can inform you of those people
considered qualified. The room heater should be inspected and cleaned before use and at
least annually by a qualified service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc.
The instructions in this manual must be strictly adhered to. Do not use makeshift methods
or compromise in the installation. Improper installation will void the warranty and safety
listing.
This heater is either approved for natural gas (NG) or for propane (LP). Burning
the incorrect fuel will void the warranty and safety listing and may cause an
extreme safety hazard. Direct questions about the type of fuel used to your dealer.
Check for a label on the flame adjust knob on the gas control valve (this is the best
place to check). You may also check for a label on the gas control valve body.
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this heater as well.
If the flame becomes sooty, dark
orange in color, or extremely tall,
do not operate the heater. Call
your dealer and arrange for
proper servicing.
It is imperative that control
compartments, screens, or
circulating air passageways of
the heater be kept clean and
free of obstructions. These
areas provide the air necessary
for safe operation.
Do not operate the heater if it is
not operating properly in any
fashion or if you are uncertain.
Call your dealer for a full
explanation of your heater and
what to expect.
Do not store or use gasoline or
other flammable liquids in the
vicinity of this heater.
Do not operate if any portion of
the heater was submerged in
water or if any corrosion occurs.
Immediately call a qualified
service technician to inspect the
appliance and to replace any part
of the control system and any
gas control that has been
underwater.

Safety Precautions 5
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Do not place clothing or other
flammable items on or near the
heater. Because this heater can
be controlled by a thermostat
there is a possibility of the
heater turning on and igniting
any items placed on or near it.
Light the heater using the built-in
igniter. Do not use matches or
any other external device to light
your heater.
Allow the heater to cool before
carrying out any maintenance or
cleaning.
The viewing glass should be
opened only for conducting
service. Do not operate with
cracked, broken, or removed
glass.
Any safety screen or guard
removed for servicing must be
replaced prior to operating the
heater.
Never remove, replace, modify,
or substitute any part of the
heater unless instructions are
given in this manual. All other
work must be done by a trained
technician. Don't modify or
replace orifices.
Operate the heater according to
the instructions included in this
manual.
If the main burners do not start
correctly turn the gas off at the
gas control valve and call your
dealer for service.
Instruct everyone in the house
how to shut gas off to the
appliance and at the gas main
shutoff valve. The gas main
shutoff valve is usually next to
the gas meter or propane tank
and requires a wrench to shut off.
This unit is not for use with solid
fuel
Do not place anything inside the
firebox (except the crushed
glass).
If any component becomes
damaged, replace with Travis
Industries components.
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Children and adults should be
alerted to the hazards of high
surface temperature and should
stay away to avoid burns or
clothing ignition. Young children
should be supervised when they
are in the same room as the
heater.
Travis Industries, Inc. grants
no warranty, implied or stated,
for the installation or
maintenance of your heater,
and assumes no responsibility
of any consequential
damage(s).
 Do not place articles on or against this appliance.
 Do not use or store flammable materials near this appliance.
 Do not spray aerosols in the vicinity of this appliance while it is in operation.
 Do not modify this appliance.
 Servicing shall be carried out only by authorized personnel.

6 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Before You Begin
 Read this entire manual before you use your new heater (especially the section "Safety Precautions"
on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or
even death.
Remote Control Warnings
KEEP BATTERIES AND COVER INSTALLED AT ALL TIMES
KEEP BATTERIES INSTALLED AT ALL TIMES
The remote control system requires the batteries to remain in place at all
times. Once the batteries are removed, the system may re-start in standing
pilot mode. If this occurs when the heater is in Remote Mode, you will not
be able to turn the heater off manually from the battery box.
If you need to replace dead batteries, make sure to turn the appliance
off before removing the batteries.
NOTE: If the batteries go dead, the system will operate normally as long
as household power (240v AC) is present.
The transmitter and IFC are radio frequency devices. Placing the transmitter in or near metal may
severely reduce the signal range.
Turn off the main gas supply to the appliance during installation or maintenance. In case of remote
control malfunction turn off the main gas supply to the appliance.
PROGRAMMING THE REMOTE
The SIT GSR2 remote may be programmed to disable the thermostat or any of the modes (flame height, blower, light,
Standing Pilot *, or auxiliary power input). This allows you to tailor the remote to the appliance.
* We do not recommend disabling the standing pilot option for our gas appliances. This feature may be recommended
for cold regions or installations with sub-optimal venting.
How to Disable/Enable the Thermostat
The remote is shipped with the thermostat enabled.
1 Remove one battery from the remote.
2 Press and hold the thermostat button while
replacing the battery. This will toggle the
thermostat function. Repeat this process to toggle
the thermostat function to the desired setting.
How to Disable/Enable Modes (Light, Blower, etc.)
The remote is shipped with all modes enabled (except AUXiliary).
1 Remove one battery from the remote.
2 Press and hold the on/off button and mode button while replacing the battery.
Keep the on/off button depressed during the following steps.
3 While keeping the on/off button depressed, press
and release the mode button until the mode that
needs to be changed is illuminated.
4 With the desired mode illuminated (see illustration
to the right), press the “up” or “down” button to
activate or clear the mode being addressed.
Make sure to keep the on/off button depressed
during this process.
5 Release the on/off button to complete
programming.

Operation 7
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Remote Set-Up
Verify the Switch is on “REMOTE”
The battery holder has a switch built into it (see Figure 1). This switch must remain in the REMOTE
position for the remote to operate.
Figure 1
Synchronize the Transmitter to the IFC
The transmitter will need to be synchronized to the IFC (Integrated Fireplace Control) before the remote
will work correctly. Synchronizing is done in the following two steps below (see Figure 2):
Press the PRG (Program) button on the battery box (IFC will beep 3 times).
Press the “ON” button on the transmitter (IFC will beep 3 times).
Figure 2
NOTE: If power is cut off to the IFC for an extended period of time, you may need to re-synchronize the
remote.
Clearing the System Memory
This appliance uses an Integrated Fireplace Control (IFC) to store the unique code for the
remote control. If you wish to clear the system memory, MAKE SURE GAS IS TURNED OFF
TO THE APPLIANCE then press the PRG (Program) button for 10 seconds. The pilot will start
to spark repeatedly, signifying all system memory has been cleared. The system will return to its
original configuration: a remote will need to be synchronized; and, the system will operate under
continuous pilot mode.

8 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Location of Controls
Direct Operation
The fireplace may be directly operated from the battery holder. The three positions are shown below:
ON (all the way left)– Burner turns on (regardless of transmitter settings).
OFF (all the way right) – Burner turns off (regardless of transmitter settings).
REMOTE (middle position) – Burner is controlled by the transmitter.
NOTE: When the battery holder switch is turned to ON or OFF, the mode settings will remain in the same
state as before the switch was moved (i.e.: the IFC “remembers” the last setting). If you wish to adjust the
mode settings use the transmitter mode button to adjust the settings (see “Mode Controls” on page 12).
The thermostat and burner on/off operating functions will not work on the transmitter.

Operation 9
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Starting the Fireplace for the First Time
 Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will
cure the painted surfaces. Fumes from the paint curing and oil
burning off the steel will occur. This is normal. We recommend
opening a window to vent the room.
 Condensation may appear on the glass each time you start the
fireplace - this is normal.
 Blue Flames will occur on the fireplace when it first comes on.
After fifteen minutes, the flames will turn a more realistic yellow
and orange color.
 Certain installations use a remote, thermostat, or wall switch to
turn the fireplace on and off. If this is the case, leave the ON/OFF
switch "ON".
 Verify the power backup and control light batteries are installed.
Pilot Fuel Conservation Timer
7 Day Pilot Shutoff Timer (applies to units in CPI mode only)
This appliance may be equipped with a 7-day pilot shutoff timer. This timer helps conserve fuel and save
money by turning the pilot off when the appliance is not used for 7 days (this timer is mandated in certain
areas for conservation purposes). This applies only when the unit is in CPI (Continuous Pilot Ignition)
mode. If the unit is in IPI (Intermittent Pilot Ignition) mode, the timer does not apply.
When in CPI mode the pilot will remain lit as long as the burner is engaged within a 7-day window. Each
time the burner is turned on the 7-day timer resets. If the burner is not engaged within the 7-day window,
the pilot will automatically revert to IPI mode and turn off to conserve fuel.
To switch back to CPI, simply:
GSB2 Units: toggle the IPI/CPI switch to IPI, then back to CPI.
GSR2 Units: use the remote to toggle from IPI mode, then back to CPI mode.
To prevent the need to reset the pilot mode during the heating season, we have listed a few strategies
below:
Option 1: Remember to periodically turn on the heater during the heating season
If you use your heater for supplemental heat, this may be the best solution. Set a specific time, once or
twice per week (e.g. 5 pm on Tuesday & Friday) to turn the heater on for a few minutes. This will reset
the timer and prevent the need to restart the pilot.
Option 2: Use a thermostat
GSR Units: Use the thermostat included with the appliance
GSB Units: Consult your dealer for thermostats compatible with your appliance.
The use of a thermostat will keep the room at a constant temperature and will, in most cases, keep the
heater working throughout the heating season. Light the pilot at the beginning of the heating season and
set the thermostat to the desired room temperature. As long as the outside temperature does not rise
excessively, for seven days or more, the pilot will continue to operate.
Option 3: Use a programmable thermostat (GSB2 Only)
A programmable thermostat may be set to turn on, once per week, to a high temperature for a short time.
This will reset the 7-day timer and allow the heater to operate without having to restart the pilot.

10 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Remote Operation
When the switch on the battery holder is set to “REMOTE” the transmitter operates the fireplace. Once
you understand how the transmitter works, you will be able to operate your fireplace quickly and easily.
Display Overview
The transmitter display has four main sections (see Figure 3).
Figure 3
Listen for the “Beep”
Each time you press a button on the transmitter that controls the fireplace, a “beep” will come from the
IFC. When you change thermostat target settings the IFC will not beep.
NOTE: When the batteries start to get low, the IFC will beep twice whenever a button is pressed. When
the batteries are nearly depleted, the IFC will no longer beep. See “IFC Batteries” on page 13).

Operation 11
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Manual On-Off / Smart Thermostat / Standard Thermostat
Use the thermostat button to cycle through the three thermostat settings (see Figure 4).
Figure 4
 MANUAL ON/OFF – The burner will turn on and off using the remote (see Figure 5). Press the
On/Off button to control the burner. When off, the display will only show the current temperature.
Figure 5
 SMART THERMOSTAT – While in smart thermostat, the transmitter will control the burner to
achieve the target temperature (see Figure 6 below). Flame height will be adjusted up or down to
allow operation without turning the burner on and off (also called “smart modulation”). To adjust
the target temperature, press the UP and DOWN buttons until a suitable temperature is achieved.
Figure 6
 STANDARD THERMOSTAT - While in standard thermostat setting, the transmitter will turn the
burner on and off to achieve the target temperature (see Figure 7 below). To adjust the target
temperature, press the up and down buttons until a suitable temperature is achieved.
Figure 7
NOTE: If the transmitter batteries go dead while in thermostat setting (standard or smart), the appliance
will shut off after approximately 24 hours.

12 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Mode Controls (Flame, Blower, EmberBed Light)
Use the mode button to cycle through the rive mode controls (see Figure 8 below).
Figure 8
Flame Height
Flame height may be controlled using the UP and DOWN buttons when in Flame Height Mode (see Figure
9 below). The center display will display the 7 settings, from “OFF” to “HI” for full on.
NOTE: Flame height may not be adjusted if operating in Smart Thermostat setting.
Figure 9
Blower Speed
The blower may be controlled using the up and down buttons when in Blower Speed Mode (see Figure 10).
The center display will display the 7 settings, from “OFF” to “HI” for full on.
Figure 10
MANUAL MODE – BLOWER OPERATION
When in Manual Mode the blower will remain on, even if the burner is turned off and the heater cools.
Either manually turn the blower off, or turn off the heater by pressing the On/Off button.

Operation 13
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Mode Controls - continued
EmberBed Light (AUX)
The emberbed light may be turned on and off using the up and down buttons (see illustration below). You
can adjust the brightness of the emberbed light using the built-in rheostat.
Display Fahrenheit or Celsius
 With the system in the “OFF” position, press both the MODE and THERMOSTAT buttons
simultaneously to toggle between Fahrenheit (F) and Celsius (C).
Low Battery Indicator
Transmitter Batteries
The transmitter has a battery-level indicator. When it indicates low battery voltage (see Figure 11 below), install
three new AAA alkaline batteries into the transmitter (see “Battery Replacement” on page 14).
Figure 11
IFC Batteries
The IFC (Integrated Fireplace Control) will “beep” twice when a transmitter button is pressed when the
batteries are low. Install four new AA alkaline batteries into the battery box when this occurs (see
“Battery Replacement” on page 14). In applications where the appliance is required to provide heat, we
recommend replacing the batteries before each heating season.

14 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Battery Replacement
Opening the Battery Box
There are (2) locking tabs in the upper corners of face of the battery box. Slide the tabs to the side and
the battery tray will pop outward enough to allow you to grab it. Pull the battery tray forward and remove
it from the battery box.
NOTE: When re-installing the battery tray, make sure to secure the battery tray into battery box using the
locking tabs to ensure a good electrical connection.
Battery Installation
Install (4) AA batteries into the battery holder (see Error! Not a valid bookmark self-reference. below).
These batteries act as a power backup in case the household (AC) current goes out.
Transmitter Battery Installation
Install the (3) included AAA batteries into the remote.
Figure 12
Child-Proof Feature
The child proof feature disables the control buttons, preventing un-wanted use of the remote.
 Press both the MODE and UP buttons simultaneously to turn this feature on and off (see Figure 13
below).
HINT: This feature is especially useful while using the thermostat setting.

Operation 15
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Figure 13
Normal Operating Odors
This appliance has several areas that reach high temperatures. Dust or other particles in these areas
may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if
the appliance was left idle for a long period.
Power Outages
Four AA batteries are used as a power backup for the fireplace in case the household (AC) power goes out. These
batteries must be inserted into battery holder (or remove receiver is using the optional GS thermostatic remote). The
fireplace controller will beep once these batteries start to go dead. Replace batteries before each heating season to
ensure proper operation.
The light and blower will not operate.
Glass Frame Removal and Installation
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for
this appliance.
The appliance must be completely cool before removing the glass.
Do not strike or slam the glass.
Warning: Do not operate appliance with the glass front removed, cracked, or broken.
Replacement of the glass should be done by a licensed or qualified service person.
 Remove the screen-trim assembly by lifting the assembly up slightly and tilting it toward you. The
mounting hooks on the back of the assembly will disengage the fireplace. Set the assembly
aside for reinstallation.
NOTE: Opening the access door on the front of the assembly allows for an easy location to get a secure
grip on the assembly for removal
Top Corner Bottom Corner

16 Operation
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Replacement Barrier Part #
24 ProBuilder 250-05282
Bottom hook
engages this slot in
bracket
Top hook engages
this slot in bracket

Maintenance 17
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Glass Removal
Replacement Glass Frame Part #
24 CF ProBuilder 250-05285

18 Maintenance
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
The latch can come loose from the glass frame anchor. This occurs when it is turned 1/4 turn when it is
disengaged. Follow the directions below to re-install the latch if it becomes loose.

Maintenance 19
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
PB 24 CleanFace - Log Installation
Installation Warnings
NOTE: Consult the installation manual for order of installation. If using propane (LP), convert the
appliance before installing the log set. If using firebacks, install them prior to installing the log
set.
 The logs are fragile, especially after being exposed to heat.
 Make sure the gas control valve is OFF and the heater is cool prior to conducting service.
 Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
 The burner must be correctly positioned before installing the log set. Make sure the burner is fully
seated and the pilot is properly aligned. See owner’s manual for details on burner removal.
Log Set Overview – Oak 94500620
When installed, the ten (10) logs should appear as shown below.
Log #10
Log #1
Log #8
Log #7
Log #2
Log #5
Log #9
Log #3
Log #4
Log #6

20 Maintenance
© Travis Industries 5/3/21 - 1529 PB 24 CF GSR2 Operation (AUST)
Installation
Log #1
Log #1 has two holes that fit over two pins on the back burner (see photos below). Place the log in place
and push it back. The log straddles the burner and does not cover any burner holes.