Lorex CVC6998HR User manual

QUICK START GUIDE
www.lorexcctv.com
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
www.lorexcctv.com
VISIT:
Lorex Technologies Inc.
Copyright © 2009 Lorex Technologies Inc.
As our products are subject to continuous
improvement, Lorex reserves the right to
modify product design, specifications and
prices, without notice and without incurring
any obligation. E&OE
It’s all on the Web!
Camera Specifications
HIGH RESOLUTION
LONG RANGE
NIGHT VISION
CAMERA
Specfications:
Precautions
• Use a UL/CSA Approved, regulated 12V DC
Power Supply.
• Make sure to install the camera in an area that
can support the camera weight.
• There are no user serviceable parts inside the
camera. Please do not disassemble the camera.
• Do not clean the lens cover with an abbrasive
cleaning material - please use a soft cloth to clean
the lens cover.
MODEL: CVC6998HR
Image Sensor 1/4” Advanced Color
Lens / Lens Mount
Video Format / Pixels
Horizontal Resolution
Minimum Illumination
Termination
IR / Night Vision Range
FOV (diagonal)
S/N Ratio
Sync. & Scan. Systems
Video Output
Power Consumption
NTSC: 656(H) x 492 (V)
480 TVL
0.6 LUX @ F1.2 (IR Off)
0 LUX (IR LEDs ON)
Video: BNC Female
Power: Barrel Female
48 IR LED/850nm/150’(46m)
36 Degrees
> 48dB
Internal; 2:1 Interlace
Comp. 1.0 Vpp @ 75ohm
400mA max
Operating Temp.
Dimensions
LxWxH
(with stand & sunshade)
14°F ~ 122°F
(-10°C ~ 50°C)
9.8” x 3.9” x 7.3”
250 mm x 100 mm x 186 mm
8.0mm F2.0/ Fixed
Iris & Shutter Speed AES; 1/60 ~ 1/50,000 sec.
Power Requirement 12V DC ±10%
Weight (with stand) 2.65 lbs / 1.20 kg
English Version 1.0

4. Connect the BNC end of the 60ft Extension Cable
to the DVR / Observation System or to a TV/VCR:
Note: Connect the BNC-to-RCA Adaptor as needed to
allow for proper connectivity.
5. Connect the A/C Power Adaptor to the 60ft
Extension cable (Black connector). Plug the
Power adaptor to a wall outlet.
Note: If the onscreen display is blurry, you may need to set the Monitor
Impedence switch to 75 ohms.
Figure 3.0 Connect the BNC cable to a DVR, CCTV, monitor or TV
ATTENTION: This Camera includes a Mechanical Auto IR Cut
Filter. When the camera changes between Day/Night Lighting, an
audible clicking noise may be heard coming from the camera. This
clicking is normal, and indicates that the Camera filter is working.
Figure 4.0 Connect power cable from BNC extension cable to
the AC Power Adaptor (included).
Contents Installing the camera
1 x High Resolution Color
Camera with attached Cable
Pass-Through Mounting
Stand
Prior to installing the camera, make sure of the
following:
• There is an opening in your mounting surface large enough for the
cables to pass through. If necessary, you can run the cables
through the pass-through ports at the top or bottom of the stand.
• You have run sufficient lengths of power and BNC extension
cables through the mounting surface to the TV, VCR, DVR, or
observation system.
To install the camera:
1. Set the camera in the desired mounting position
and mark holes for the screws.
2. Drill the holes, then feed the cable through the
mounting surface and mount the camera stand to
the desired surface using the provided screws.
Make sure all four screws are fastened tightly at
the connection points.
3. Set the position and angle of the camera using the
provided Allen key.
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the cameras and
cables to the TV,VCR, DVR or Observation System.
Figure 1.0 Attach the stand to the mounting surface.
Figure 2.0 Use the Allen key (included) to set the camera’s angle and
position and then lock in place.
• 1/4” Advanced Image Sensor (AIS) provides a High
Resolution image (480 TV Lines)
• Auto Mechanical IR Cut Filter removal function ensures
accurate color reproduction
• Durable Weatherproof Indoor/Outdoor camera*
• Enhanced Night Vision Capability - up to 150 ft / 46m **
* Not recommended for submersion in water
** IR Illumination range of 150 ft. (46m) under ideal conditions.
Objects at or beyond this range may be partially or completely
obscured, depending on the camera application.
WARNING - A REGULATED UL/CSA APPROVED 12V DC 500mA
power supply is REQUIRED for use with this camera. Use of a non-
regulated, non-conforming power supply can damage this product
and will void the warranty.
4 x Mounting screws
1 x Allen key
Connecting the camera
Setup Diagram:
Features
1 x 60ft. BNC/Power
Extension Cable
1 x BNC to RCA
Adaptor
1 x AC Power Adaptor