Lorex DCP1000 User manual

AUTO PAN TILT COLOR DOME
CAMERA FOR USE WITH VISTAPRO4
DIGITAL MONITORING SYSTEM
DCP1000
DYNACOLOR

1
FEATURES & FUNCTIONS
Reliable, high quality 1/4" CCD Camera providing optimum image clarity
Connects to computer via Interface box and RS232C – RS485 converter*
Remote PAN/TILT control with VistaPro4 software
Slow speed Pan/Tilt operation (15° per second) at 355° pan and 80° tilt range
3.6mm lens, 1Lux (F 2.0)
CONTENTS
This Package Contains:
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
!
Explanation of two Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance-(servicing) instructions in the literature
accompanying the appliance.
WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO
RAIN OR MOISTURE.
!
Pan Tilt Controller
Interface Module
DCP1000 Color Auto Pan
Tilt Color Dome Camera
65 ft DIN extension
and 7 ft RS485
connection cables
*IMPORTANT NOTE:
THIS AUTO PAN TILT DOME CAMERA CANNOT FUNCTION ON VISTAPRO4 SOFTWARE
WITHOUT THE ACC-RS232 CONNECTOR ACCESSORY (SOLD SEPARATELY)

2
Pan Tilt Controller Interface Module
Port Description Connection Type
To Camera RS-485 data input/ video input 6 Pin DIN jack
To DVR Serial data output / video output 6 Pin DIN jack
SW 1 -6 Camera ID selection 6 Pin DIP switch
TO CAMERA
- transmits the Pan/Tilt control signals from the VistaPro 4 to the DCP1000 Dome Camera
- receives the video signal from the DCP1000 Camera to the VistaPro 4.
TO DVR
- receives the RS-485 signal from the PC’s Comm port (via the ACC-RS232 connector)
- transmits the video signal that comes from Pan/Tilt Dome Camera to DVR.
6 PIN DIP SWITCH
- sets the Channel ID of Pan/Tilt Dome Camera to correspond to the channel on the VistaPro4.
Refer to the diagram below for how to set the Dip Switch to correspond with a camera.
1 2 3 4 5 6
ON
CAM
ID: 1
1 2 3 4 5 6
ON
CAM ID: 2
1 2 3 4 5 6
ON
CAM ID: 3
1 2 3 4 5 6
ON
CAM ID: 4
①CAMERA INPUT
CONNECTOR
②DVR INPUT
CONNECTOR
③6PIN DIP
SWITCH
①②③

3
INSTALLATION
Ensure electrical power is not connected to the dome camera and PC system
during installation.
DIAGRAM SHOWING TYPICAL SET-UP
Important Note:
For the P/T/Z Camera Model setting in the Camera menu of Setup in the VistaPro4, the
DCP1000 is the “DYNACOLOR” camera in the drop down menu.
STEP BY STEP SETUP INSTRUCTIONS
Step 1: Mounting the Camera
Separate the back-plate from the base of the camera by gently twisting the base while
securing the back plate.
Attach the camera back plate on the ceiling using the Ø3 X 20 screws (supplied)
Secure the camera to the ceiling by gently twisting the base of the camera onto the
ceiling mounted back plate
Connect the 65’ Camera DIN cable to the female DIN input found on the Camera.
Connect the other end of the cable to the Interface box.
RS-485(+)
RS-485(-)
RS-232C
(to PC COM Port)
(VistaPro 4 Main
Board)
VIDEO
DC12V
7ft
RS485
Cable
65ft
6Pin Din
Cable
Pan/Tilt
Dome Camera
PT
Interface
RS-232C to RS-485
CONVERTER
Do not hold clear bubble or the swivel when attaching the camera to
the back plate.

4
Step 2: Connecting the Camera to the VistaPro4 Digital Video Capture Card
At the location of the PC, plug the other end of the 65’ Camera DIN cable into the DIN
port labeled “To Camera” found on the PT interface module.
Using the 7’ RS-485 Connection Cable, connect the end terminated with the DIN plug to
the port labeled “To DVR” (next to the DIP switches) on the PT Interface module.
On the other end of the RS-485 Connection Cable, screw the single orange wire into the
“TX +” terminal of the ACC-RS232, and the green wire to the “TX –” terminal.
Plug the RCA jack (from the RS-485 Connection cable” into the desired Camera Input
found on the VistaPro4 card.
Connect the ACC-RS232 connector into an available DB9 Comm Port.
Step 3: Setting the Camera Address
The Dip Switch setting of the camera connected to the PT Interface must correspond to
the RCA Camera Input of the VistaPro 4
TECHNICAL SPECS: DCP1000 Pan/Tilt Dome Camera
Image sensor 1/4" Color CCD
Active pixels 512(H) X 492(V)
Image sensor area 4.8(H) X 3.7(V) mm
Resolution > 330 TV lines
Min. illumination 1 Lux (F2.0)
Video output 1.0V p-p (75 ohms)
Electronic iris 1/60 ~ 1/100,000 sec
Lens 3.6mm
Synchronization Internal
Signal format 525 lines, 2:1 interlace
System connection 6 Pin Mini DIN jack
Power source DC12V (from interface or controller)
Power consumption MAX. 2.4W
Operating temperature -10°C ~ +50°C
Dimension 126 X 107 mm
Weight 1Kg
Pan/Tilt speed 15° per second
Pan travel 355°
Tilt travel 80°