Lorex LNZ32P4 SERIES User manual

Instruction
Manual
LNZ32P4 SERIES
4x IP PTZ DOME
CAMERA
LNZ32P4_MANUAL_TRILINGUAL_R2

Thank you for purchasing this product. Lorex is committed to providing our customers with
a high quality, reliable security solution.
This manual refers to the following model:
LNZ32P4
For the latest online manual, downloads and product updates, and to learn about our
complete line of accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
THE PLUG TO THE WIDE SLOT AND FULLY INSERT.
#LX400075; r.38010/38010; en-US iv

Table of contents
1 Safety Instructions ..............................................................1
2 Getting Started ...................................................................2
3 Connecting the Camera .......................................................3
3.1 OPTION 1: Connecting Cameras to an NVR.....................3
3.2 OPTION 2: Connecting Cameras to the Local Area
Network (LAN) ...........................................................3
4 Installation .........................................................................8
4.1 Installation Tips and Warnings .......................................8
4.2 Installation (Indoor/Outdoor)..........................................8
4.2.1 Wall Mounting .................................................9
4.2.2 Ceiling Mounting............................................ 15
5 Controlling the PTZ Camera with an NVR.............................. 16
5.1 Controlling a PTZ Camera (Local NVR) ......................... 16
5.2 Advanced PTZ Controls ............................................. 17
5.2.1 Presets........................................................ 18
5.2.2 Tours........................................................... 19
5.2.3 Pattern......................................................... 20
6 Technical Specifications .................................................... 22
6.1 Dimensions ..........................................................................23
7Troubleshooting................................................................ .............25
8Resetting the Camera ........................................................ ...........27
9Notices ............................................................................ ...............29
9.1 FCC/IC Notice ......................................................... ...........29
9.2 Modification............................................................. ............29
9.3 ROHS .................................................................... .............29
#LX400075; r.38010/38010; en-US v

Safety Instructions
1
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity, and voltage levels
noted in the Technical Specifications.
• Camera is rated for outdoor use and is weatherproof when properly in-
stalled. Camera is not intended for submersion in water. Installation under
a sheltered environment is recommended.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of intense
light.
• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
• Make sure to install the camera in a location that can support the camera
weight.
• Make sure there are no live electrical cables in the area where you plan to
mount the camera.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any-
thing other than water to clean the dome cover, as chemicals such as ace-
tone can permanently damage the plastic.
#LX400075; r.38010/38010; en-US 1

Getting Started
2
The system comes with the following components:
IP PTZ Dome Camera
100ft (30.5m) Cat5e UL
Compliant Ethernet Ex-
tension Cable
Allen Key (x2)
(One included in the mounting
hardware kit of the camera,
and one included in the
mounting
hardware kit of the wall mount-
ing bracket)
Mounting Template
Mounting Screws (x3)
& Anchors (x3)
(For camera)
Wall Mounting Bracket
Mounting Screws ST4 (x4)
& Anchors S6 (x4)
(For wall mounting bracket)
Hex Bolt M4x10 (x3)
(For wall mounting
bracket)
Installation Diagram Guide
and Instructional Manual
#LX400075; r.38010/38010; en-US 2

Connecting the Camera
3
It is recommended to connect the camera to your NVR and test the PTZ con-
trols before permanent installation. For instructions on how to setup PTZ con-
trols, see 5 Controlling the PTZ Camera with an NVR.
3.1 OPTION 1: Connecting Cameras to an NVR
1. Connect the PoE connector on the camera cable to the included Ethernet
extension cable.
2. Connect the Ethernet extension cable to one of the PoE ports on the back
panel of your NVR.
NOTE
You can use a single CAT5e Ethernet cable up to 300ft (91m) to connect the camera to
your NVR. Compatible with all Lorex HD NVRs, excluding the LNR200 & LNR300 Ser-
ies. For the most up-to-date list of compatible recorders, please visit www.lorextechnology.
com/support
3.2 OPTION 2: Connecting Cameras to the Local Area Network (LAN)
For flexibility, you may also connect the camera to the same Local Area Net-
work (LAN) as the NVR. This is accomplished by connecting the camera to
the same
router (not included) as the NVR. For these installations, an external
PoE switch (sold separately) or power adapter (not included) must be used to
provide power to the camera. You must also add the camera on the NVR be-
fore it will show a
picture on the monitor or be recorded by the NVR.
What is PoE?
PoE is a technology that allows Ethernet cables to carry electrical power to
connected devices. Compatible NVRs use integrated PoE ports to provide
#LX400075; r.38010/38010; en-US 3

Connecting the Camera
3
power and PTZ commands to the camera, as well as video connection to the
NVR over a single CAT5E cable. In order to use PoE with this IP camera, you
must connect it directly to a compatible NVR or a PoE switch on the same net-
work as the NVR.
For the most up-to-date list of compatible recorders,
please visit www.lorextechnology.com/support
PoE switches are available for purchase on www.lorextechnology.com.
Complete the following steps to connect the camera to the NVR over the LAN.
Step 1 of 2 — OPTION A: Connecting the camera to your local network
using an
optional PoE switch:
1. Connect an Ethernet cable of up to 300ft (91m) rated CAT5e or higher
(not included) from the LAN port on an external PoE switch (sold sepa-
rately on www.lorextechnology.com) to your router. Connect the power ca-
ble to the PoE switch and plug into a power outlet or surge protector.
NOTE
Terminology may vary depending on the model of PoE switch you have.
#LX400075; r.38010/38010; en-US 4

Connecting the Camera
3
2. Connect the camera to the PoE switch using the included Ethernet cable
(or a CAT5e Ethernet cable of up to 300ft (91m)). The PoE switch will pro-
vide power and video transmission the same way as your NVR.
Step 1 of 2 — OPTION B: Connecting the camera to your local network
using a power adapter:
1. Connect the camera to a power adapter (not included).
NOTE
For power requirement specification, see 6 Technical Specifications.
2. Connect the camera to a router in the same network as your NVR using
the included Ethernet cable (or an Ethernet cable of up to 300ft (91m)
rated CAT5e or higher).
Step 2 of 2: Add the camera to your NVR:
CAUTION
The following instructions are based on the Lorex LNR400 Series NVR. See your NVR’s in-
struction manual for instructions on controlling the PTZ camera with your system.
1. Right-click and select Device Search.
#LX400075; r.38010/38010; en-US 5

Connecting the Camera
3
2. Log in using the admin account (default User Name: admin; default Pass-
word: 000000).
3. Click Device Search. The system searches the network for compatible
cameras.
4. Check the camera(s) you would like to add.
#LX400075; r.38010/38010; en-US 6

Connecting the Camera
3
5. Click Add. The Status indicator turns green to show the camera is suc-
cessfully connected.
6. Click OK to save changes.
NOTE
You can also add a camera to a specific channel by hovering the mouse over an empty
channel in split-screen view and clicking . Click Device Search and double-click the
camera you would like to add. Right click to exit.
#LX400075; r.38010/38010; en-US 7