Love My Skin Luxury Glass Diffuser User manual

Luxury Glass Diuser
“Hello Beautiful”
Thank you for your purchase of the Love My Skin Luxury Glass Diuser.
Please read the instructions and safety tips before use.

Page 1
ATTACHMENT & SPECIFICATIONS
Applicable area
Working temperature
Input voltage
Rated voltage
Power consumption
Tank Capacity
Misting output
Packaging size
15m² – 20m²
15-40˚C
100 volts-240 volts AC
DC 5V
Max 7.5 W
100ML
≥15ml/hr
Max: 285x205x178mm
Min 247x172x170mm
Material
Dimension
Ultrasonic rate
Accessories
Quantity
Weight
Gross
PP+ABS+PC+Silicon
Ø95x150mm
3.0MHz
AC power adapter
USB Cable User Manual
X1
144g-169g
Max: 1172.1g
Min: 647.8g
STANDARD PACKAGING CONTAINS:
FEATURES
SPECIFICATIONS
1 x Love My Skin Diuser 1 x USB Cable 1 x instruction manual
• Near silent operation
• Quick start
• Colour changing LED
• Fine mist
• USB-powered (plug adapter not included)

Page 2
COMPONENTS
Glass cover
In-cover
Cup
Base

Page 3
OPERATION
1.
2.
3.
4.
5.
6.
Place the diuser correctly on a flat surface, remove the glass cover and the
in-cover from the main body.
Fill water tank with water, no higher than the maximum water level line (150ml).
Add 2-3 drops of essential oils into the water tank. Essential oil can be more or less
according to personal preference.
Replace the in-cover and the glass cover to the original position of the main body.
Plug adapter into USB slot of computer or Plug the AC adapter into the power socket.
Press button to turn on the device and set as follows:
Press button first time to turn on and start mist continuously
Press button second time to turn o and stop mist
Press button third time to turn o and stop mist
Press button to turn on the LED illumination and set LED mode:
• Diuser comes with dierent LED lights to provide ambience that suits you.
When the diuser detects water is below the minimum threshold, the device will
automatically enter standby mode. To reactivate repeat steps 1-6

Page 4
CLEANING & MAINTAINANCE
1.
2.
3.
4.
5.
6.
Unplug unit and pour out remaining water.
Use soft cloth with water to clean the main body and outer shell lightly.
After cleaning place in ventilated area to dry.
Disinfect with cotton swab dipped in alcohol and clean the dirt of the ultrasonic
plate gently (picture A).
Replace the cover of the aroma diuser (picture B).
Store in cool dry place.
NOTE:
1.
2.
Do not use acid or alkaline or other strong cleaning agents on unit. May cause
damage or discolouration.
Change water daily. Do not use mineral water or water temperature above
15-40˚C in unit.
Picture A Picture B

WARNINGS
NOTICE:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
2.
3.
Keep the diuser out of reach of children.
Do not move when it is filled with water.
Do not fill water in use.
Do not exceed the maximum water level line.
Place unit on stable, level surface. Do not block steam outlet.
Unplug power supply during maintenance. Do not use if cord is damaged. Do not pull
forcefully on cord and keep clear of pathways.
Clean the water tank weekly.
When not in use, remove water from tank.
This appliance is not intended for the use of children. Anyone planning to use this
product must read the instructions thoroughly before use.
Before adding water and cleaning should first disconnect the power.
The product is subject to change without prior notice.
Pictures for reference only.
Patented products, rights reserved.
Page 5
WARNINGS & NOTICE

Page 6
TROUBLESHOOTING & SUPPORT
Problem
Product stops
working
Water is over the
max fill line
Issue of water smell
when product is
not in use
Little or no mist
is being produced
The glass cover
and inner cover
do not fit properly
Water is leaking
from the diuser
Cause
Water below
minimum
threshold
Power cables
disconnected or
damaged
Too much water
has been added
The diuser has
not been cleaned
regularly
The diuser has
not been cleaned
regularly
The covers have
been incorrectly
installed
Covers could be
misaligned or
tank overfill
Solution
Refill as per operational instructions 1-6
Check connection to the diuser
Check connection to the USB plug
adapter
Check there is no damage to the cable
– replace if necessary (contact
customer services)
Remove excess water to below the
max line
Clean the diuser as per instructions
Clean the diuser as per instructions
Remove both covers and reinstall taking
care to place them in the correct position
Remove then replace both covers
ensuring they are not misaligned.
If tank is overfilled then disconnect from
power and remove some of the water.

WARRANTY & SUPPORT
LMSD2 UK IB 20180815
Page 7
Symbol for "Environment Protection" – Waste electrical
products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your
local Authority or retailer for recycling advice.
Symbol for “Complies with EU requirements”.
Fragile; handle with care
Model Reference.
Symbol for “Manufacture Date”.
Symbol for “Fragile; handle with care”.