Lovencare TREK User manual

Instruction Manual
“TREK” Activity Centre
Item:BP 571
IMPORTANT: PLEASE READ INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE!

2
WARNING
R ead all instructions before assembly and use of the stationary activity center. Keep
instructions for future use. DO NOT use the stationary activity center if it is damaged
or broken.
WARNING:
•Use only for a child who is able to hold head upright unassisted and who is not able to walk
or climb out of product.
•Never leave child unattended. Always keep child in view while in product.
(or product description ).
•Never use near steps.
•
•Strings can cause strangulation! DO NOT place items with a string around child’s neck, such
as hood strings or pacifier cords. DO NOT suspend strings over product or attach strings to
toys.
•Requires two “AA” (LR6) alkaline batteries (not included) for toy operation.
•Use only for a child:
-who is able to hold head up unassisted.
-who is not able to climb out.
-who weighs less than 25 lbs.(11.3kg) and is less than 32 inches (81cm) in height.
•This baby activity center should be used only for short periods of time (e.g.20 mins).
•Do not use replacement parts other than those approved by the manufacturer or distributor.
•WARNING: Do not use this activity center as a swing.
•The child will be dangerous of play nearby jumping walker.
•Keep child in the middle of seat correctly.
Cleaning:
•Clean with a damp sponge or cloth and mild detergent. Do not use abrasives or bleach.

3
Parts list
Tool Needed:
1. Phillips Screwdriver (not included)
Plush Arch Toy x1
Seat Back x1
Seat Ring x1
Seat Pad x1
Legs x3
Spinner Toys x2
Base x1 Tray x1
Arch Toy x1
Music Tray x1

STEP 1
4
ASSEMBLE THE LEGS TO
THE BASE
1. Insert a leg into the slot
on the base, see diagram
2. Press the leg down into
the “Base” until the leg
button locks into the base.
3. Repeat steps 1-2 for other
two legs.

STEP 2
5
ATTACHING THE LEGS TO
THE TRAY
1. Position the tray on top
of the legs, see diagram.
2. Push down and ensure
the buttons lock into place.
3. Repeat steps 1-2 for other
two legs.

STEP 4 STEP 3
6
Position the two spinner toys
into the round holes on the
tray, see diagram. Push the
spinner toys into the holes
until the studs on the ends
of the spinner toys lock over
the housings on the underside
of the tray and cannot be
Slot the plush arch toy into
the round holes on the tray,
see diagram.
Make sure both lock hooks
snap into the lock hook
holes.

STEP 6 STEP 5
7
battery
battery
Befor
will need to fit the batteries.
Unfasten the screw in the battery
cover using a X-head screwdriver.
Insert two ‘AA’ batteries, ensure
that the batteries ar
correct way round.
Rry cover and tighten
the screw.
Slot the plush arch toy
into the round holes
on the main tray,
see diagram.
Make sure both lock
hooks snap into the lock
hook holes.

8
STEP 7STEP 8
QuietLoud
ATTACHING MUSIC TRAY ON
THE TRAY
1. Slot the music tray on the
tray, see diagram. Ensure
both front locks hook into
the openings.
2. Push down on the back of
music tray. Ensure that both
back locks are securly in place.
Slide the switch on the
back of the music insert
music or loud music.
on the front of the music
tunes.

9
STEP 9
ATTACH THE SEAT PAD
1. Insert the seat back into the
slots on the tray, see diagram.
Pull up on the seat back to
ensure that it is securly
locked into place.
2. Pull the crotch section of the
seat pad outwards, the warn-
ing label will be at the back
and the adjustment strap for
the seat pad will be at the
bottom.
3. Place seat pad into seat ring
located on “Tray”. Align it so
that the highest point of the
seat pad aligns with back of
the walker.
4. Slide tabs through holes.
1.
2.
4.
3.

10
STEP 10STEP 11
ASSEMBLE THE SEAT UNIT ONTO
THE TRAY
1. Slot the assembled seat into the
hole in the middle of the tray.
While holding the sides up the
tray, push down on the seat ring
until the dips on the seat ringlock
over the edge of the tray.
2. Turn the seat unit over and check
the all of the six sips have locked
over the edge of the tray. Also pull
up on the seat to onsure that it will
Once fitted the seat will rotate freely.
LOCKING SYSTEM FOR SEAT UNIT
There are two locking positions under
the seat unit, see diagram.
Insert the pin to prohibit the seat unit
from rotating.

11
STEP 12
FUNCTION FOR THE
PEDAL BASE
1. You will see two circular
pedals on the base for
the trek. There is a lock
on the base as well.
2. When unlocked, your
child can learn to walk
by moving on the
pedals.
3. When locked the pedals
will not move.
unlock
lock

STEP 13
12
ADJUST THE HEIGHT BY THE
SEAT PAD
To raise the height of the seat:
Grip the buckle on the rear of the
seat pad. Pull the loose end of the
webbing away from the buckle
until the correct heigh is achieved.
You may need to place the child in
the seat several times before the
correct height is achieved.
To lower the height of the seat:
Push the button on the top of the
buckle inwards (A) and hold. Feed
the webbing through the buckle (B)
until the seat is the correct height.
You may need to place the child in
the seat several times before the
correct height is achieved.
Care & maintenance
1. Wipe plastic parts with a damp cloth using mild soap.
2. Machine wash seat pad in cold water in gentle cycle. Do not use harsh detergents or bleach.
Do not dry clean.
3. Air or line dry.
4. To maintain stopping performance, clean friction strips regularly with damp cloth.

13
.
Contact Us:
Love N Care Pty Ltd.
297-299 Canterbury Rd, Revesby
NSW 2212 Australia
Contact No: 02 9774 4655
Fax: [phone]
Email: [email protected]
Website: www.lovencare.com.au