Lovencare SENATOR JIT300 User manual

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
SENATOR CHEST
JIT300

1.

Parts Checklist
2.

Assemble Drawers
Step 1. Fit Locking pins to front and side panels x2
Lay the front and side panels face down on the floor and screw 2x locking pins into the treaded holes on each
side panel and screw 4x locking pins into the threaded holes on the front panel (2 at end of each front panel)
Screw 4x locking pins into the back of
the front drawer panel, 2 at each end Screw 2x locking pins into each side panel
Step 2 - Fit the locking cams to the back panel and side panels x2
Lay the back and side panels on the floor with the large holes facing upwards,
insert 4x cam locks into the back panel and 2 cam locks into each side panel.
Insert 1x dowel into the hole above the 2x locking pins on the
side panels.Align and insert the dowel and locking pins on the
side panel to the back panel and tighten the cam locks.
Repeat so both side panels are attached to the back panel.
Note: Check that the grooves for the drawer base is facing
inwards.
Step 3 - Side Panels to back Panels
Step 4 - Fit the drawer base
Place the assembled drawer on the floor an insert the
base into the grooves in the side panels.
Reinforcing strip faces downwards.
3.

Place drawer handle in position over the 2 holes
in the front panel and insert 2x drawer screws
through the back of the drawer front and into
the drawer handle and tighten.
Step 5 - Fit the front panel
Stand the Assembled drawer upright, align the
drawer front, dowels and locking pins with the
corresponding holes and attach the drawer front.
Tighten all cam locks
Step 6 - Fit Drawer handle
Step 7 - Fit drawer runners
Turn the drawer runner upside down on the
floor. Place drawer runner in position - with the
wheel on the runner at the back of the drawer, and
pushing the drawer runner up against the drawer front
panel.
Note: there are left and right drawer runners.
Screw 3x self tapping screws through the runner into
the side panel.
The Drawer is complete - Repeat for all drawers 4.

Note: The pointed end of the
cross on the cam locks must
point in the direction the
locking pins will be inserted from.
Assemble the Drawer enclosure
Step 1 - Fit locking pins to side panels and dowel to base
Turn the base the correct way up and insert 8x wooden dowels.
Lay the side panels outside facing down and insert 1x locking pin and one x dowel into each side panel.
Step 2 - Fit the back panel support and
lower back panel to side panels.
Stand one side panel up on its back edge, attach the back
panel support and tighten the cam lock.
Whilst supporting the first side panel repeat and attach the
second side panel tothe back support.
Slide a back panel into the grooves on the side panels and into
the groove in the back support.
Step 3 - Fit Base to side panels
Whilst the side panels remain supported attach the
base aligning the dowels in the base with the holes
in the end of the side panels amd back panel with
the groove in the base.
Insert 4x30mm bolts (2 on each side) through the holes
in the square bards attached to the side panel and
into the threaded nuts in the base and tighten.
5.

Check all cam locks and bolts are tight.
Insert the drawers carefully onto their runners
Step 4 - Fit the upper back panel and top to base side panels
Stand the case upright carefully.
Insert the top back panel into the
grooves on the side panels
and the back panel support.
Insert 4x dowels into the holes on
the top of each side panel.
Place the top onto the case
aligning holes in top with the
dowels.
Insert 2x30mm bolts through the
holes in supports on each side
panel and into top and tighten
with an allen key.
The enclosure is complete - insert drawers and attach the change tray.
6.

All Love N Care products are guaranteed for twelve months from the date of purchase.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. you are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. This covers against faults which develop
through faulty materials and workmanship.
Misuse, accidental damages,normal wear and tear or neglect are not covered.
If a fault becomes apparent, please return the item to the store of purchase with your
receipt. You must inform the store what the defect is. We will then arrange for its repair
or it will be assessed for replacement as expediently as possible. The benefits of this
warranty are in addition to other right and remedies under the law in relation to the goods
or services to which this warranty relates.
If you are unable to return the item to the store of purchase, you can contact Love N Care
on free call 1300 732 599.
Where you send the product directly to the manufacturer then you may be liable for
the costs of transportation to and from Love N Care. Love N Care will meet the reasonable
expenses incurred by a consumer in a making a warranty claim. You can claim expenses
incurred in making a claim by contacting our customer service team on 1300 732 599 or
by email at [email protected]
7.