Loveshaw LITTLE DAVID CF5 User manual

LITTLE DAVID
OWNERS MANUAL
CF5/C/E
THE LOVESHAW CORPORATION LOVESHAW - EUROPE
2206 EASTON TURNPIKE, BOX 83 UNIT 1, NEWTON PARK
SOUTH CANAAN, PA 18459 W. PORTWAY INDUSTRIAL ESTATE
ANDOVER, HAMPSHIRE SP103SH
TEL: [phone] ENGLAND
FAX: [phone]-3575-11
P/N: PM-CF5/EV
Valid from 08/17

LOVESHAW
TABLE OF CONTENTS
SECTION #1 GENERAL SAFETY PRECAUTIONS
SECTION #2 MACHINE SPECIFICATIONS
SECTION #3 INSTALLATION PROCEDURE
SECTION #4 SEQUENCE OF OPERATION
SECTION #5 MACHINE ADJUSTMENTS
SECTION #6 MACHINE OPERATION
SECTION #7 TROUBLE SHOOTING
SECTION #8 WARRANTY
SECTION #9 TABLE OF CONTENTS
ILLUSTRATED ASSEMBLIES
SECTION #10 ELECTRICAL

LOVESHAW
GENERAL SAFETY PRECAUTIONS
BEFORE INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT, READ THE FOLLOWING PRECAUTIONS
CAREFULLY:
1. THIS MACHINE IS EQUIPPED WITH MOVING PARTS. DO NOT PLACE HANDS IN THE MACHINE
WHEN PARTS ARE MOVING.
2. DO NOT BYPASS ANY DESIGNED-IN SAFETY FEATURES SUCH AS INTERLOCKS, GUARDS
OR SHIELDS.
3. DO NOT PLACE HANDS OR BODY INSIDE CONFINES OF MACHINE WHILE IT IS RUNNING.
4. SAFETY GLASSES SHOULD BE WORN WHEN WORKING ON OR AROUND MACHINE.

LOVESHAW
MACHINE SPECIFICATIONS
MACHINE MODEL: CF5
INFEED/OUTFEED HEIGHT: MINIMUM: MAXIMUM:
22 1/4” 30 1/4”
BOX CAPACITY: MINIMUM: MAXIMUM:
LENGTH: 8” (203 mm) 26 1/2” (672 mm)
WIDTH: 6” (152 mm) 20” (508mm)
HEIGHT: 3.5” (89 mm) unlimited
MACHINE SPEED: UP TO 15 BOXES PER/MIN., DEPENDING ON BOX SIZE AND
OPERATOR’S DEXTERITY.
MACHINE SIZE:
LENGTH: 37.5” (953 mm)
WIDTH: 26“ (660 mm)
HEIGHT: 22” (559 mm)
AIR REQUIREMENTS: 3 SCFM @ 40 - 50 PSI
CF5 FEATURES:
* ERECTS BOXES WITHOUT USING ANVIL PLATE
* ERECTED BOXES ARE POSITIONED ON ROLLER BED FOR EASY TRANSFER TO CASE SEALER
* THREE POINT SAFETY SWITCH ACTUATION PROTECTS AGAINST ACCIDENTAL STARTING
* ONE MINUTE BOX SIZE CHANGE-OVER
* FLAP FOLDING SYSTEM POWER FOLDS ALL BOTTOM FLAPS
* MAJOR FLAPS, KEEP BOTTOM FLAPS OF BOX ALIGNED FOR HASSLE FREE FOLDING
* MECHANICAL BOX HOLD DOWN, KEEPS BOX IN PLACE FOR HANDS FREE BOX LOADING
* CAN BE EASILY INCORPORATED WITH ANY CASE SEALER IN THE INDUSTRY
* STAINLESS STEEL COVERS
* CORROSION RESISTANT CONSTRUCTION
* WELDED FRAME
* POWDER COAT FINISH
* SLIDE AND LOCK LEGS
* ARTICULATING SIDE ROLLER DESIGN FOR EASE OF LOADING
* PROGRAMMABLE LOGIC CONTROL SEQUENCE

LOVESHAW
INSTALLATION PROCEDURE
EXERCISE CARE WHEN HANDLING THIS MACHINE, A SUDDEN JOLT OR JAR MAY CAUSE SERIOUS DAMAGE.
DO NOT REMOVE THE SHIPPING SKID UNTIL MACHINE HAS BEEN MOVED TO A POINT OF INSTALLATION.
THE SKID IS DESIGNED FOR EASY AND SAFE HANDLING OF YOUR MACHINE. UNPACK MACHINE AND REMOVE
ANY MATERIALS USED TO PROTECT COMPONENTS DURING SHIPPING.
IF MACHINE IS PLACED DIRECTLY ON FLOOR, FRAME BASE MUST BE LEVEL TO ENSURE PERSONAL SAFETY,
PREVENT UNDO STRESS TO THE FRAME, AND MAXIMUM PERFORMANCE.
THE CF5 IS INTENDED TO OPERATE IN A HORIZONTAL POSITION. DO NOT ATTEMPT TO TILT THE CF5 TOWARD
THE OPERATOR, THIS WILL CAUSE EXCESSIVE WEAR ON THE BOX WIDTH ADJUSTMENT ASSEMBLY AND MAY
CAUSE IT TO JAM OR EVEN DAMAGE THE WIDTH ADJUSTMENT SCREW.
THE CF5 SHOULD BE SECURELY MOUNTED IN-LINE WITH ADJOINING EQUIPMENT TO PREVENT IT FROM MOVING
AS IT OPERATES.
AIR SUPPLY MAY COME FROM EITHER A SEPARATE SOURCE OR BY TAPPING OFF THE SUPPLY OF AN ADJOINING
CASE SEALER. THE AIR SUPPLY TO THE MACHINE SHOULD BE CLEAN AND DRY, AS THE FILTER IS ONLY MEANT
TO REMOVE MINOR PARTICLES OR SLIGHT AMOUNTS OF MOISTURE IN THE AIR LINE. DIRT OR MOISTURE CAN
CAUSE THE ERRATIC OPERATION OF CONTROL VALVES.
AIR SHOULD BE SET AT 50 PSI, WITH A MINIMUM OF 40 PSI AND A MAXIMUM OF 60 PSI.

LOVESHAW
MACHINE ADJUSTMENTS
CAUTION:
BEFORE MAKING ANY CHANGES OR ADJUSTMENTS, SWITCH OFF OR DISCONNECT ELECTRICAL AND AIR
SUPPLY TO THE MACHINE (*). FOLLOW OSHA LOCK OUT / TAG OUT PROCEDURE.
MACHINE SET UP:
SET-UP FOR THE CF5 CONSISTS OF THREE SEPARATE ADJUSTMENTS:
- BOX WIDTH (*)
- BOX LENGTH
- POSITION OF MAJOR FLAP FOLDER PLATES (**)
(*) THIS ADJUSTMENT REQUIRES MACHINE TO BE TURNED ON.
(**) AFTER INITIAL SET-UP, THIS ADJUSTMENT IS REQUIRED ONLY WHEN THERE IS A LARGE DIFFERENCE IN
BOX SIZE.
BOX WIDTH (1):
1. ATTACH THE HAND CRANK (SUPPLIED WITH THE MACHINE) ON THE SQUARE SHAFT THAT EXTENDS
FROM EITHER SIDE OF THE FRAME. OPEN THE FRAME WIDER THAN THE BOX.
2. TURN MACHINE ON. THIS MOVES ROLLER PLATES AND ROLLERS OUT OF THE WAY SO OPERATOR
CAN MAKE AN EASY AND PROPER ADJUSTMENT.
3. OPEN A BLANK BOX AND INSERT IT INTO THE MACHINE.

LOVESHA:
4. USING THE HAND CRANK, TURN WIDTH ADJUSTMENT UNTIL THE BOX HOLD-DOWN ROLLERS ARE
LIGHTLY GRIPPING THE SIDES OF THE BOX. IT SHOULD BE EASY TO INSERT THE BOX WITHOUT
FORCE.
BOX LENGTH (2):
1. REMOVE BOX. LOOSEN THE CLAMP AT THE BASE OF THE FRONT MINOR FLAP FOLDING ASSEMBLY.
(MINOR FLAP FOLDING ASSEMBLY)
MINOR FLAP
FOLDER
BOX HOLD-
DOWN ROLLER

LOVESHAW
2. REINSERT BOX INTO THE MACHINE AND POSITION IT 1/2” BACK FROM THE MINOR FLAP FOLDER AT
THE EXIT END OF THE MACHINE. PUSH THE MINOR FLAP FOLDER FORWARD UNTIL IT JUST CONTACTS
THE BACK OF THE BOX. REMOVE THE BOX AND TIGHTEN THE MINOR FLAP FOLDER CLAMP.
MAJOR FLAP FOLDER PLATES (3):
THERE ARE TWO MAJOR FOLDER PLATES ON EACH SIDE OF THE MACHINE, ONE SMALLER AND ONE LARGER
THAT ARE ADJUSTED INDIVIDUALLY.
THE MAJOR FLAP FOLDING PLATES AND WHEELS MAY BE EXTENDED TO PROVIDE ADDITIONAL SUPPORT FOR
WIDE HEAVY BOXES OR RETRACTED FOR NARROW BOXES.
CAUTION:
DO NOT SET MAJOR FLAP FOLDING PLATES IN THE EXTENDED POSITION WHILE RUNNING VERY NARROW
BOXES. THIS WILL CAUSE THE MAJOR FLAP FOLDING WHEELS TO CONTACT THE MINOR FLAP FOLDING
ASSEMBLY AND WEDGE AGAINST THE BOTTOM CONTROL/FLAP OPENER BRACKET. IF FORCED, EITHER OF
THESE CONDITIONS CAN DAMAGE MACHINE COMPONENTS.

LOVESHAW
1. ON EACH SIDE, LOOSEN THE FOUR SOCKET HEAD CAP SCREWS THAT HOLD THE FOLDER PLATES
IN PLACE. SLIDE THE FRONT (LARGER) MAJOR FOLDER PLATE TO DESIRED POSITION AND RETIGHTEN
THE SCREWS. REPEAT PROCEDURE FOR THE REAR (SMALLER ) FOLDER PLATE.
CAUTION:
FOR VERY WIDE BOXES, THE SMALLER FOLDER PLATE WILL NOT BE ABLE TO BE EXTENDED AS
FAR AS THE LARGER PLATE.
FRONT (LARGER)
MAJOR FOLDER
PLATE
PLATE ADJUSTMENT
SOC. HEAD CAP
SCREWS
REAR (SMALLER)
MAJOR FOLDER
PLATE

LOVESHAW
MACHINE OPERATION
BEFORE STARTING MACHINE, DISCONNECT COMPRESSED AIR AND ELECTRICAL POWER TO THE UNIT.
ACTUATE ALL MOVING PARTS BY HAND TO CHECK ADJUSTMENTS FOR ANY MECHANICAL OBSTRUCTION.
RECONNECT UTILITIES AND TURN ON MACHINE. KEEP HANDS CLEAR OF MOVING PARTS.
ERECTING A BOX:
1. OPEN AND SQUARE OFF BOX.
2. PLACE BOX, BOTTOM OPEN, INTO CF5. PUSH THE BOX DOWN UNTIL IT MAKES CONTACT WITH
THE TWO BOTTOM PHOTO EYES.
3. THE MACHINE WILL FOLD THE FRONT AND REAR MINOR FLAPS FIRST, AND THEN THE TWO SIDE MAJOR
FLAPS. THE BOX IS HELD IN PLACE AND IS READY TO FILL, IF DESIRED.
4. WHEN THE BOX IS ERECTED (AND FILLED), PUSH IT OUT OF THE CF5 FOR THE NEXT OPERATION.
5. AS THE TRAILING END OF THE BOX BREAKS CONTACT WITH THE PHOTO EYE, THE CF5
WILL AUTOMATICALLY RESET FOR THE NEXT BOX.

LOVESHAW
OPERATING CYCLE:
1. THERE ARE THREE PHOTO EYES THAT MUST BE ACTUATED FOR THE MACHINE CYCLE TO START.
THE TWO PHOTO EYES (NOT SHOWN) ACTUATED BY THE BOTTOM EDGES OF THE MAJOR FLAPS,
AND THE SIDE PHOTO EYE (NOT SHOWN) ACTUATED BY THE SIDE OF THE BOX.
(PHOTO EYE PLACEMENT)
2. THE TWO SMALL LEVERS OF THE MAJOR FLAP OPENERS TEMPORARILY OPEN THE MAJOR FLAPS AS
THE MINOR FLAPS ARE FOLDED.
(MAJOR FLAP OPENERS)
MAJOR FLAP
OPENER (FLIPS
UP TO OPEN)
SIDE
PHOTO EYE
BOTTOM
PHOTO EYES

LOVESHAW
3. THE MINOR FLAP FOLDERS FOLD BOTH END FLAPS ON THE BOTTOM OF THE BOX AND THEN RETRACT.
(REAR MINOR FLAP FOLDER)
(FRONT MINOR FLAP FOLDER)
REAR MINOR
FLAP FOLDER
FRONT MINOR
FLAP FOLDER

LOVESHAW
4. THE MAJOR FLAP FOLDERS THEN FOLD BOTH SIDE FLAPS ON THE BOTTOM OF THE BOX AND STAY IN
POSITION TO SUPPORT THE BOX FOR FILLING. THE HOLD DOWN ROLLERS THEN EXTEND OUTWARD
TO HOLD THE BOX IN POSITION.
(MAJOR FLAP FOLDERS)
5. AS THE OPERATOR PUSHES THE BOX OUT OF THE MACHINE, THE WHEELED BODY SWITCH
RESETS AND THE MACHINE IS READY FOR THE NEXT BOX.
MAJOR FLAP
FOLDERS AND
WHEELS

LOVESHAW
(BOX LENGTH SCALE)
(BOX WIDTH SCALE)

PREVENTATIVE MAINTENANCE SCHEDULE
EVERY SHIFT
1. WIPE ANY DUST OFF THE PHOTO EYES WITH A RAG.
DAILY
1. BLOW ANY DUST, DIRT, OR DEBRIS OFF THE MACHINE USING COMPRESSED
AIR.
WEEKLY
1. CHECK AND CLEAN THE AIR FILTER.

LOVESHAW
TROUBLESHOOTING GUIDE
A. DURING FOLDING OR FILLING CYCLE, 1. CHECK TO SEE IF WIDTH ADJUSTMENT IS CORRECT.
BOX RELEASES, ALL FLAPS DROP. IF IT IS TOO WIDE, THE PHOTO EYE THAT
CONTACTS
THE SIDE OF THE BOX WILL RESET AND CAUSE
THE MACHINE TO RETURN TO THE START POSITION.
2. SHAKING THE BOX TO LEVEL THE CONTENTS CAN
CAUSE THE PHOTO EYE TO RESET.
B. MAJOR FLAPS HAVE PROBLEMS FOLDING 1. MAKE SURE THE MAJOR FLAP OPENERS ARE
AND CAUSE INNER EDGES OF MINOR FLAPS SET CORRECTLY SO THEY TEMPORARILY
TO BE FOLDED OVER. OPEN THE MAJOR FLAPS WIDER AND ALLOW
THE MINOR FLAPS TO CLEAR THE INSIDE OF
THE MAJOR FLAPS BEFORE RELEASING.
2. CHECK THAT AIR PRESSURE IS ADEQUATE AND
THAT AIR PRESSURE DOES NOT DROP DURING
THECYCLE.
C. DURING MINOR FLAP FOLDING, BACK 1. BE SURE THAT THE BOX WIDTH SETTING DOES
OR FRONT OF BOX COLLAPSES INWARD. NOT HOLD BOX TOO TIGHTLY.
2. CHECK THE AIR PRESSURE SETTING.
3. CHECK THAT THE SCORING ON THE BOX IS
ADEQUATE AND PROMOTES FOLDING.
D. BOX TRANSFER FROM CF5 1. CHECK THE HEIGHT OF THE ROLLERS AT
INTO CASE SEALER IS THE OUTFEED END OF THE CF5 AND THAT
NOT SMOOTH. THE BOX CLEARS THE MACHINE FRAME.
2. CHECK THE ALIGNMENT OF THE MACHINES
TO EACH OTHER. MAKE SURE THE WORKING
SURFACE (HEIGHT) OF BOTH MACHINES ARE
CO-PLANAR.

LOVESHAW
WARNING:
ALTHOUGH THE CF5 CAN BE USED WITH COMPETITIVE CASE SEALER/TAPERS, LOVESHAW ASSUMES NO
RESPONSIBILITY FOR SAFETY ISSUES RESULTING FROM THESE APPLICATIONS. WE DO NOT RECOMMEND
USING THE CF5 IN CLOSE PROXIMITY WITH CONVENTIONAL KICKERS AND/OR THREE FLAP FOLDERS.
CAUTION:
BEFORE CONNECTING THE AIR SUPPLY TO THE MACHINE, BE SURE THAT THE MAIN ON/OFF AT THE
AIR CONNECTION IS SHUT OFF AND THAT THE RED EMERGENCY STOP BUTTON IS PUSHED DOWN.
FOLLOW OSHA LOCK OUT / TAG OUT PROCEDURES.
BEFORE DOING ANY MAINTENANCE OR SERVICE, BE SURE THAT THE MACHINE IS DISCONNECTED FROM
THE AIR SOURCE AND ELECTRICAL POWER. THIS WILL PREVENT ACCIDENTAL MACHINE MOVEMENTS THAT
COULD RESULT IN PERSONAL INJURY.
NEVER LEAVE THE MACHINE UNATTENDED WHILE THE MACHINE IS TURNED ON.
MACHINE SHOULD ONLY BE OPERATED BY QUALIFIED PERSONNEL!!!!!!

Little David® Warranty
For: CASE FORMER MODELS
CF20-T, CF30-T, CF40-T, CF40T-XL MODELS
1 YEAR WARRANTY ON DRIVE MOTOR
1 YEAR WARRANTY ON GEAR REDUCER
3 YEAR WARRANTY ON TAPE CARTRIDGE (EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL
WEAR, TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY
TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.)
1 YEAR ON PLC
1 YEAR ALL OTHER PARTS (EXCEPT FOR WEAR AND MOVING PARTS.)
For: CASE FORMER MODEL
CF5
1 YEAR ON PLC
1 YEAR ALL OTHER PARTS (EXCEPT FOR WEAR AND MOVING PARTS.)
*LIMITED WARRANTY – LOVESHAWCOMPANY (HEREIN AFTER “LOVESHAW”) WARRANTS ONLY THAT THE GOODS
SOLD BY IT SHALL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP, UNDER PROPER AND NORMAL USE AND
MAINTENANCE, AS FOLLOWS:
DRIVE MOTOR - 1 YEAR
GEAR REDUCER - 1 YEAR
TAPE CARTRIDGE - 3 YEARS (EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL
WEAR, TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY
TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.)
PLC - 1 YEAR
ALL OTHER PARTS - 1 YEAR (EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL
WEAR, TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY
TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.)
THE WARRANTY PERIOD SHALL COMMENCE AS OF THE DATE OF DELIVERY TO THE PURCHASER. THE OBLIGATION OF
LOVESHAW UNDER THIS WARRANTY IS STRICTLY LIMITED TO THE COST OF REPAIRING OR REPLACING, AS LOVESHAW
MAY ELECT, ANY PART OR PARTS THAT PROVE IN LOVESHAW’S JUDGMENT TO HAVE BEEN DEFECTIVE IN MATERIAL OR
WORKMANSHIP AT THE TIME THE GOODS WERE SHIPPED FROM LOVESHAW’S PLANT. ANY WARRANTY CLAIM NOT MADE
IN WRITING TO LOVESHAW AT ITS HOME OFFICE WITHIN THE APPLICABLE WARRANTY PERIOD AND WITHIN 10 DAYS OF
FAILURE WILL NOT BE VALID. THIS IS THE SOLE AND EXCLUSIVE REMEDY AVAILABLE UNDER THIS WARRANTY. UNDER
NO CIRCUMSTANCES WILL LOVESHAW BE LIABLE FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES.
IF REQUESTED BY LOVESHAW, PURCHASER SHALL RETURN ANY DEFECTIVE PART OR PARTS TO LOVESHAW’S PLANT,
FREIGHT PREPAID. ALL WARRANTY PART REPLACEMENTS AND REPAIRS MUST BE MADE BY LOVESHAW OR A LOVESHAW
AUTHORIZED TO HANDLE THE GOODS COVERED BY THIS WARRANTY. ANY OUTSIDE WORK OR ALTERATIONS DONE
WITHOUT LOVESHAW’S PRIOR WRITTEN APPROVAL WILL RENDER THIS WARRANTY VOID. LOVESHAW
WILL NOT ASSUME ANY EXPENSE OR LIABILITY FOR ANY REPAIRS MADE TO ITS GOODS OUTSIDE ITS WORKS WITHOUT ITS
PRIOR WRITTEN CONSENT. THIS WARRANTY SHALL NOT APPLY TO ANY ITEM THAT HAS NOT BEEN USED, OPERATED, AND
MAINTAINED IN ACCORDANCE WITH LOVESHAW’S RECOMMENDED PROCEDURES LOVESHAW SHALL HAVE NO LIABILITY
WHATSOEVER WHERE THE GOODS HAVE BEEN ALTERED, MISUSED, ABUSED OR INVOLVED IN AN ACCIDENT.
NO PERSON IS AUTHORIZED TO MAKE ANY WARRANTY OR TO CREATE ANY LIABILITY BINDING UPON LOVESHAW. WHICH
IS NOT STATED IN THIS WARRANTY. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND,
EXPRESSED OR IMPLIED, WHICH ARE HEREBY EXCLUDED. IN PARTICULAR, THE IMPLIED WARRANTY OF
MERCHANTABILITY, AS WELL AS THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
EXCLUDED.
LOVESHAW COMPANY
2206 EASTON TURNPIKE, BOX 83 SOUTH CANAAN, PA 18459
TEL: [phone] - FAX: [phone]

 LOVESHAW
TABLE OF CONTENTS
ILLUSTRATED REPLACEMENT PARTS
FRAME ASSEMBLY
FRONT MINOR FOLDER ASSEMBLY
REAR MINOR FLAP FOLDER ASSEMBLY
WIDTH ADJUSTMENT ASSEMBLY
PRE FOLDER ASSEMBLY
MAJOR FLAP FOLDER ASSEMBLY
PNEUMATIC ASSEMBLY
ELECTRICAL

1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
TITLE
DWG NO SCALE
DRAWN
CHECKED
APPROVED
LOVESHAW
RT. 296, SOUTH CANAAN, PA.

MATERIAL
TOLERANCES UNLESS
OTHERWISE NOTED:
INCH
METRIC
.X
.XX
.XXX
= .050
= .015
= .005
+
-+
+
--
-
.X
.XX
.XXX
= 1.0mm
= .3mm
= .1mm
+
+
+
-
-
-
FRACTIONS 1/64
+
-
ANGLES 1/2
+
-
-
MACH.
FINISH 125
CAD FILE
PLOT DATE
DRAWN DATE
DO NOT SCALE PRINT
MAT'L
ST. ST.
STD
PART #
STAINLESS : NO FINISH
THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF
LOVESHAW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY
INFORM ATION. THIS D RAWING OR SU BJECT MA TTER THEROF SHALL NOT B E
REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER
WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAW AND WILL BE
RETURNED TO LOVESHAW UPON REQUEST. BRYCEF
6/11/2013
FRAME ASSY
FRAME ASSEMBLY
FRAME ASSY.idw
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
BOTTOM MAIN BEAM
PFF-0000-611
REAR U-FRAME ASSEMBLYPFF-0055-6EV12
FRONT U-FRAME ASSY.PFF-0054-6EV13
80/20 MOUNT BRACKETPFF-0001-3EV24
HOSE GUARDPFF-0069-415
FRONT BRACE
PFF-0030-616
LEGS
PFF-0049-647
SUPPORT MOUNTPFF-0033-4EV18
SKID PLATEPFF-0038-419
LEAD SCREW SUPPORTPFF-0035-4110
BRONZE BUSHINGBSG-1063211
LEAD SCREW SUPPORT
PFF-0062-4112
COVER REARPFF-0040-6EV113
E-STOP MOUNTPFF-0088-4EV114
CAP - TUBINGPFF-0039-4EV415
T-SLOT EXTRUSIONPFF-0057-4EV116
SHLD BOLT, M6 x 70mm LG.SPH-1512217
ROLLER
RL-1000EV618
FLAT WASHER M6FFWMGP1819
BLOCK, LEG ADJUSTERPFF-0105-3EV420
BH M8x12 LG.FBHMH012P10421
LOCK WASHER M8FLWMHP622
BHCS M6 X 16FBHMF016P10823
LOCK WASHER M6FLWMGP
1424
FLAT WASHER M10FFWMIP825
LOCK WASHER M10FLWMIP1226
HEX NUT M10FHFNMIP1227
HHCS M10 X 30FHHMI030P88428
HHCS M5 X 12
FHHMF012P10229
LOCK WASHER M5
FLWMFP230
FLAT WASHER M5FFWMFP231
FHCS M5 X 0.8 X 12 LG.FFHMF012P10332
FHCS M6 X 1.0 X 16 LG.FFHMG016P10233
HHCS M6 X 16 FHHMG016P10434
FHCS M8 X 20 LG.
FFHMH020P10235
HHCS M6 X 20FHHMG020P10
236
M4 x 12 BUTTON HEADFBHME012P10837
HHCS M8 X 20FHHMH020P10238
FLAT WASHER M8FFWMHP439
HEX NUT M8FHFNMHP240
TOGGLE PADSPH-1194EV
441
HEX JAM NUT, M10, PLATED
FHJNMIP
842
HH M10x35mm LGFHHMI035P88843
HHCS M10 x 60mm, FULL THRD., SSSPH-1580444
WIRE / HOSE CRADLEAH203645
BHCS M5 X 0.8 X 10 LG.FBHMF010P10546
BUTTON HEAD, M5 x 6
FBHMF006P10147
GUARD LEFTPFF-0042-6SS148
GUARD RIGHTPFF-0041-6SS149
M6 FLAT WASHERSPH-1496450
REVISION HISTORY
REV DESCRIPTION DATE BY
A RELEASED 6/11/2013 BJF
49
50
23
24
38
39
14
35
39 22
13
40
12
11
37
15
7
45
47
5
31
30
29
48
50
24 23
7
25
28
16
1
46
46
46
45
45
22
21
41
27 27
20
42
26
42
44
43
2
3
7
4
9
19
24 23
17
32
8
19
24
34
6
33
19
18
11
10
19
24
36
19
24
34