LSI MegaRAID LSIiBBU01 User manual

®
This Quick Installation Guide explains how to install the LSI
Logic MegaRAID LSIiBBU01 Intelligent Battery Backup Unit
on a MegaRAID SATA 300 PCI-X to Serial ATA storage
adapter. The LSIiBBU01 protects the cached data on the
MegaRAID storage adapter by providing backup power if the
main AC power source fails or is interrupted.
The LSIiBBU01 is compliant with the Smart Battery Data
Specification, which relieves the host system from the
responsibility of communicating battery information and
charging the battery.
You can view information about the LSIiBBU01, such as
battery temperature and voltage, in the BIOS Configuration
Utility and the WebBIOS Configuration Utility. Battery
charging and recharging takes place automatically.
The following sections describe how to install the LSIiBBU01
and list the basic hardware specifications for it.
Installing the LSIiBBU01 on the Storage
Adapter
Caution: Electrostatic discharge can damage the
LSIiBBU01 and the MegaRAID SATA 300 storage
adapter. Be sure to install the LSIiBBU01 at an
ESD-safe workstation that meets the
requirements of EIA-625 – “Requirements For
Handling Electrostatic Discharge Sensitive
Devices.” When you install the LSIiBBU01, follow
the ESD-recommended practices in the latest
revision of IPC-A-610.
If the MegaRAID SATA 300 storage adapter is already
installed in a computer, follow these steps to remove it before
you install the LSIiBBU01:
Step 1 Shut down the computer, turn off the power, and
unplug the power cord(s).
Step 2 Remove the cover from the computer according
to the instructions in the system user’s manual,
so you can access the PCI-X slots.
Step 3 Ground yourself before touching the MegaRAID
SATA 300 storage adapter.
Step 4 Unplug all cables from the MegaRAID SATA 300
storage adapter, remove the screw attaching the
bracket to the computer case, and carefully
remove the storage adapter from the slot.
Step 5 Place the storage adapter on a flat, clean, static-
free surface, and continue with the next section.
Follow these steps to install the LSIiBBU01 on the
MegaRAID SATA 300 storage adapter:
Step 1 Ground yourself, and remove the LSIiBBU01 from
its package.
Figure 1 shows top and bottom views of the
LSIiBBU01. Note the J2 and J14 connectors and
the holes for the screws that attach the
LSIiBBU01 to the MegaRAID SATA 300 storage
adapter.
Figure 1 LSIiBBU01 Intelligent Battery Backup
Unit
Step 2 Insert the battery pack harness connector (at the
end of the colored wires) into the J2 connector on
the bottom side of the LSIiBBU01.
Step 3 Place the MegaRAID SATA 300 storage adapter
front-side-up on a flat, clean, static-free surface.
Step 4 Hold the LSIiBBU01 so that the battery side is up
and the J14 connector lines up with the J3
connector on the MegaRAID SATA 300 storage
adapter, as shown in Figure 2.
Bottom View
Top View
J14
J2
MegaRAID®LSIiBBU01 Battery
Backup Unit
Quick Installation Guide
MR_LSIiBBU01_QuickIG.fm Page 1 Thursday, October 14, 2004 4:22 PM

Order No. S14079 P/N: 80-00055-01
DB11-000061-00, Version 1.0, October 2004
Find a list of LSI Logic Corporation’s U.S. distributors, international distributors,
sales offices, and design resource centers on the LSI Logic web site at:
http://www.lsilogic.com/contacts/index.html
®LSI Logic, the LSI Logic logo design, and MegaRAID are trademarks or registered
trademarks of LSI Logic Corporation. All other brand and product names may be
trademarks of their respective companies.
Copyright © 2004 by LSI Logic Corporation. All rights reserved.
LSI Logic Corporation reserves the right to make changes to any products and ser-
vices herein at any time without notice. LSI Logic does not assume any responsi-
bility or liability arising out of the application or use of any product or service
described herein, except as expressly agreed to in writing by LSI Logic; nor does
the purchase, lease, or use of a product or service from LSI Logic convey a license
under any patent rights, copyrights, trademark rights, or any other of the intellec-
tual property rights of LSI Logic or of third parties.
Figure 2 Connecting the LSIiBBU01
Step 5 Carefully press the LSIiBBU01 onto the storage
adapter, so the J3 and J14 connectors are firmly
joined.
Step 6 Using the three Philips-head screws that are
provided, secure the LSIiBBU01 to the storage
adapter, as shown in Figure 2.
Caution: Center the screwdriver carefully to avoid stripping
the screw heads. Do not over-tighten the screws.
The maximum recommended torque is 2.25 inch
pounds.
Step 7 Install the MegaRAID SATA 300 storage adapter
in a PCI-X slot in the computer, as shown in
Figure 3.
Press down gently, but firmly, to ensure that the
storage adapter is properly seated in the slot. The
bottom edge of the storage adapter must be flush
with the slot.
Caution: Never apply pressure to the LSIiBBU01 when
inserting the adapter. Instead, press down only
on the top edge of the storage adapter board, as
shown in Figure 3.
Step 8 Attach the storage adapter to the computer
chassis with the bracket screw.
Figure 3 Installing the Storage Adapter
Step 9 Attach the cables, as needed, to the connectors
on the MegaRAID SATA 300 storage adapter.
Step 10 Replace the computer cover and reattach the
power cord(s).
LSIiBBU01 Hardware Specifications
•Supports DDR1 memory technology.
•Can be used with models 300-8X and 300-4X of the
MegaRAID SATA 300 storage adapter.
•Battery capacity is 4.22 Wh.
•Reference retention time is 72 hours for 128 MB standard
cache on the MegaRAID SATA 300 storage adapter,
using 256Mb x 16 DDR1 memory chips.
•LSI Logic recommends that you replace the LSIiBBU01
after one year of service.
J3
Connector
64-bit Slots
(3.3 V)
Bracket Screw Press Here
Press Here
MR_LSIiBBU01_QuickIG.fm Page 2 Thursday, October 14, 2004 4:22 PM