LSIS Starvert iG5A Series User manual

0.4~1.5kW 1phase 200~230Volts
0.4~22kW 3Phase 200~230Volts
0.4~22kW 3Phase 380~480Volts
iG5A
www.lsis.com
Compact & Powerful Drive

LS Starvert iG5A is very competitive in its price and shows an upgraded functional strength.
User-friendly interface, extended drive ranges up to 22kW,
superb torque competence and small size of iG5A provides an optimum use environment.
Drive
STARVERT iG5A
Standard
compliance
High
performance
Compactness
User-
friendliness
& Easy
maintenance
iG5A
2

Overview
Model & Type
Standard Specifications
Wiring
Terminal Configurations
Keypad Features
Parameter Setting
Trial Run
Dimensions
Braking Resistors and Peripheral Devices
Function List
Protective Functions
Fault Remedy
4
8
9
11
13
15
16
18
20
23
25
42
43
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series
Contents
3

Condition:
Speed vs Torque Characteristics
Speed (Hz)
Torque (%)
Sensorless Vector Control Mode: Auto tuning Measure maximum
torque (%) at each speed (1/5/10/20/30/40/50/60Hz)
+10
-10
Speed
Time
With braking resistor
Reducing
deceleration time
Normal state
iG5A
Powerful & Upgraded Performance
Sensorless vector control
Ground-fault protection
during running
Analog control from -10V to 10V
Forward
PID controlPID control
Pl controlPI control
Reverse
Built-in PID control
Built-in dynamic braking circuit
Built-in 485 communication
Wide product range
The built-in sensorless vector control provides
the superb speed control and powerful high
torque.
The ground-fault protection of output terminal
is possible during running.
Inputting analog signals from -10V to 10V
provides user-friendly operation.
The built-in PID function enables to control
flow-rate, oil-pressure, temperature, etc
without any extra controller.
The built-in dynamic braking circuit minimizes
deceleration time via braking resistors.
The built-in RS-485 communication supports
remote control and monitoring between iG5A
and other equipment.
iG5A consists of the product range from 0.4 to 22KW.
iG5A provides sensorless vector control, PID control,
and ground-fault protection through powerful built-in functions.
4

Checking operation status
(Voltage, Current, Frequency, etc)
Checking modified parameters
Windows support
Monitoring
Connected to PC
Connected to XGT panel
Checking operation time
Automatic list-up of trip record
Language support (Korean, English, Chinese)
Monitoring
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Drives
RS-485, Modbus communication
Remote Control
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Drives
RS-485, Modbus communication
Remote Control
RS-485 - 232C converter
RS-485 communication
5
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

iG5A
User-friendly Interface & Easy Maintenance
The parameter setting becomes easier by adopting the 4 directions key. And iG5A supports
easy maintenance via diagnosis and fan changeable structure.
Diagnosis of output module
Easy change of fan
Cooling fan control
User-friendly interface
External loader (Optional)
Through easy parameter setting, iG5A can diagnose the
status of output module.
iG5A is designed to be the fan changeable structure in
preparation for a fan breakdown.
By controlling the cooling fan, iG5A provides a virtually
quiet environment according to the status of operation.
The 4 directions key provides easy handling and
monitoring.
Loader type + External type (Optional)
The external loader away from a panel enables to control
and monitor conveniently. And the parameters made by
external loader can be copied and applicable to other
Drives.
Model name
INV, REMOTE KPD 2M (SV-iG5A)
INV, REMOTE KPD 3M (SV-iG5A)
INV, REMOTE KPD 5M (SV-iG5A)
Remarks
2m
3m
5m
6

Compact Size
The compact size achieves cost-efficiency and various applications.
Same height from 0.4 to 4.0kW (128mm)
Global standard
PNP/NPN input
iG5A series complies with CE and UL standards.
Both PNP and NPN inputs become possible and these enable to
use the outer power.
To do so, users will be given wider choices of selecting the
controller.
Global standard compliance
CE UL
7
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

iG5A
Model & Type
Applicable motor ranges 1 Phase 200V 3 Phase 200V 3 Phase 400V
0.4kW (0.5HP)
0.75kW (1HP)
1.5kW (2HP)
2.2kW (3HP)
3.7kW (5HP)
4.0kW (5.4HP)
5.5kW (7.5HP)
7.5kW (10HP)
11.0kW (15HP)
15.0kW (20HP)
18.5kW (25HP)
22.0kW (30HP)
SV004iG5A-1
SV008iG5A-1
SV015iG5A-1
SV004iG5A-2
SV008iG5A-2
SV015iG5A-2
SV022iG5A-2
SV037iG5A-2
SV040iG5A-2
SV055iG5A-2
SV075iG5A-2
SV110iG5A-2
SV150iG5A-2
SV185iG5A-2
SV220iG5A-2
SV004iG5A-4
SV008iG5A-4
SV015iG5A-4
SV022iG5A-4
SV037iG5A-4
SV040iG5A-4
SV055iG5A-4
SV075iG5A-4
SV110iG5A-4
SV150iG5A-4
SV185iG5A-4
SV220iG5A-4
SV
STARVERT
iG5A series
Motor rating (kW)
(004: 0.4kW~220: 22kW)
Input voltage
(1: 1 phase 200~230[V], 2: 3 phase 200~230[V], 4: 3 phase 380~480[V])
015 iG5A 2
8

SV iG5A-1
5)
4)
Max.
capacity
1)
(HP)
(kW)
Output
rating
Capacity (kVA)
FLA (A)
Max frequency
Max voltage
Rated voltage
Rated frequency
Cooling method
Weight (kg)
Input
rating
1) Indicate the maximum applicable motor capacity when using 4 pole LS standard motor.
2) Rated capacity is based on 220V for 200V series and 440V for 400V series.
3) Refer to 15-3 of userʼs manual when carrier frequency setting (39) is above 3kHz.
4) Max. frequency setting range is extended to 300Hz when H40 (Control mode select) is set to 3 (Sensorless vector control).
5) Max. output voltage cannot be higher than the input voltage. It can be programmable below input voltage.
6) Self-Cooling
2)
3)
015008004
2
1.5
3.0
8
1.84
1
0.75
1.9
5
1.12
0.5
0.4
0.95
2.5
0.76
400 [Hz]
3 phase 200~230V
1phase 200~230 VAC (+10%, -15%)
50~60 [Hz] (±5%)
Forced air cooling
SV iG5A-2
5)
4)
Max.
capacity
1)
(HP)
(kW)
Output
rating
Capacity (kVA)
FLA (A)
Max frequency
Max voltage
Rated voltage
Rated frequency
Cooling method
Weight (kg)
Input
rating
2)
3)
004 008 015 022 037 040 055 075 110 150 185 220
0.5
0.4
0.95
2.5
0.76
1
0.75
1.9
5
0.77
2
1.5
3.0
8
1.12
3
2.2
4.5
12
1.84
5
3.7
6.1
16
1.89
5.4
4.0
6.5
17
1.89
7.5
5.5
9.1
24
3.66
10
7.5
12.2
32
3.66
15
11
17.5
46
9.0
20
15
22.9
60
9.0
25
18.5
28.2
74
13.3
30
22
33.5
88
13.3
400 [Hz]
3 phase 200~230V
3 phase 200~230 (+10%, -15%)
50~60 [Hz] (±5%)
Forced air coolingN/C
6)
SV iG5A-4
5)
4)
Max.
capacity
1)
(HP)
(kW)
Output
rating
Capacity (kVA)
FLA (A)
Max frequency
Max voltage
Rated voltage
Rated frequency
Cooling method
Weight (kg)
Input
rating
2)
3)
004 008 015 022 037 040 055 075 110 150 185 220
0.5
0.4
0.95
1.25
0.76
1
0.75
1.9
2.5
0.77
2
1.5
3.0
4
1.12
3
2.2
4.5
6
1.84
5
3.7
6.1
8
1.89
5.4
4.0
6.5
9
1.89
7.5
5.5
9.1
12
3.66
10
7.5
12.2
16
3.66
15
11
18.3
24
9.0
20
15
22.9
30
9.0
25
18.5
29.7
39
13.3
30
22
34.3
45
13.3
400 [Hz]
3 phase 380~480V
3 phase 380~480 VAC (+10%, -15%)
50~60 [Hz] (±5%)
Forced air coolingN/C
6)
Standard Specifications
1 Phase 200V
3 Phase 200V
3 Phase 400V
9
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

1) Means average braking torque during Decel to stop of a motor.
2) Refer to Chapter 16 of userʼs manual for DB resistor specification.
Over voltage, Under voltage, Over current, Ground fault current detection, Drive overheat,
Motor overheat, Output phase open, Overload protection, Communication error,
Loss of speed command, Hardware fault, Fan trip
V/F, Sensorless vector control
Linear, Squared, User V/F
150% per 1 min.
Manual/Auto torque boost
20%
150% when using optional DB resistor
Digital command: 0.01Hz
Analog command: 0.06Hz (Max. freq.: 60Hz)
Digital command: 0.01% of Max. output frequency
Analog command: 0.1% of Max. output frequency
Trip
Alarm
Momentary power loss
Operation mode
Frequency setting
Operation features
Dynamic
braking
Input
Output
Max. braking
torque
Max. Duty
Open collector
terminal
Multi-function relay
Analog output (AM)
IP 20, NEMA1 (Optional)
-10℃~50℃
-20℃~65℃
Below 90% RH (No condensation)
Below 1,000m, 5.9m/sec2(0.6G)
70~106 kPa
Protected from corrosive gas, Combustible gas, Oil mist or dust
1)
2)
Keypad/ Terminal/ Communication option/ Remote keypad selectable
PID, Up-down, 3-wire
NPN/PNP selectable
0~10Vdc (less than 10mA): Output freq, Output current, Output voltage, DC link selectable
FWD/REV RUN, Emergency stop, Fault reset, Jog operation, Multi-step Frequency-High, Mid, Low,
Multi-step Accel/Decel-High, Mid, Low, DC braking at stop, 2nd motor select, Frequency UP/Down,
3-wire operation, External trip A, B, PID-Drive (V/F) operation bypass,
Option-drive (V/F) operation bypass, Analog Hold, Accel/Decel stop
Analog: 0~10V, -10~10V, 0~20mA
Digital: Keypad
Fault output and
drive status output
Less than DC 24V, 50mA
(N.O., N.C.) Less than AC 250V, 1A; Less than DC 30V, 1A
Stall prevention, Overload
Below 15 msec.: Continuous operation (Should be within rated input voltage, rated output power.)
Above 15 msec.: Auto restart enable
Protection degree
Ambient temp
Storage temp
Humidity
Altitude/Vibration
Atmospheric pressure
Location
Control method
Frequency setting resolution
Frequency accuracy
V/F pattern
Overload capacity
Torque boost
Multi-function
terminal
P1~P8
Environ
ment
Control
Protective
function
Operation
iG5A
Standard Specifications
10

P1
P2
CM
P3
P4
P5
CM
P6
P7
P8
24
R
S
T
G
U
V
W
AM
CM
3A
3C
3B
MO
MG
S+
S-
DB resistor
(Optional)
3 phase AC input
(Rated input voltage)
VR
V1
I
CM
B1 B2
A contact output
A/B contact common
B contact output
FX (Forward run)
RX (Reverse run)
Input signal common
BX (Emergency stop)
RST (Trip reset)
JOG (Jog operation)
Input signal common
Multi-step freq. - Low
Multi-step freq. - Middle
Multi-step freq. - High
24V output
Ground
10V power supply for potentiometer
Freq. Setting Voltage signal input: -10~10V
Freq. Current signal input: 0~20mA
Input signal common
Multi-function open
collector output
MO Common
Potentiometer
(1kohm, 1/2W)
RS-485 communication terminal
Multi-function
analog output
signal: 0~10V
Wiring
0.4~7.5kW
11
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

P1
P2
CM
P3
P4
P5
CM
P6
P7
P8
24
R
S
T
G
U
V
W
AM
CM
3A
3C
3B
MO
MG
S+
S-
DB resistor
(Optional)
DC reactor
3 phase AC input
(Rated input voltage)
VR
V1
I
CM
P1(+) B1 B2 N(-)
A contact output
A/B contact common
B contact output
FX (Forward run)
RX (Reverse run)
Input signal common
BX (Emergency stop)
RST (Trip reset)
JOG (Jog operation)
Input signal common
Multi-step freq. - Low
Multi-step freq. - Middle
Multi-step freq. - High
24V output
Ground
10V power supply for potentiometer
Freq. Setting Voltage signal input: -10~10V
Freq. Current signal input: 0~20mA
Input signal common
Multi-function open
collector output
MO Common
Potentiometer
(1kohm, 1/2W)
RS-485 communication terminal
Multi-function
analog output
signal: 0~10V
iG5A
Wiring
11.0~22.0kW
12

R, S, T wire U, V, W wire Ground wire
mm
2
AWG mm
2
AWG mm
2
AWG
Terminal
Screw Size
Screw Torque
(kgf.cm) / lb-in
• 0.4kW~0.75kW (1 phase)
• 1.5kW (1 phase)
• 0.4kW~1.5kW (3 phase)
SV0004iG5A-1
SV0008iG5A-1
SV0015iG5A-1
SV0004iG5A-2
SV0008iG5A-2
SV0015iG5A-2
SV0022iG5A-2
SV0037iG5A-2
SV0040iG5A-2
SV0055iG5A-2
SV0075iG5A-2
SV0110iG5A-2
SV0150iG5A-2
SV0185iG5A-2
SV0220iG5A-2
SV0004iG5A-4
SV0008iG5A-4
SV0015iG5A-4
SV0022iG5A-4
SV0037iG5A-4
SV0040iG5A-4
SV0055iG5A-4
SV0075iG5A-4
SV0110iG5A-4
SV0150iG5A-4
SV0185iG5A-4
SV0220iG5A-4
M3.5
M3.5
M4
M3.5
M3.5
M3.5
M4
M4
M4
M5
M5
M6
M6
M8
M8
M3.5
M3.5
M4
M4
M4
M4
M5
M5
M5
M5
M6
M6
10/8.7
10/8.7
15/13
10/8.7
10/8.7
10/8.7
15/13
15/13
15/13
32/28
32/28
30.7/26.6
30.7/26.6
30.5/26.5
30.5/26.5
10/8.7
10/8.7
15/13
15/13
15/13
15/13
32/28
32/28
30.7/26.6
30.7/26.6
30.5/26.5
30.5/26.5
2
2
2
2
2
2
2
3.5
3.5
5.5
8
14
22
30
38
2
2
2
2
2
2
3.5
3.5
5.5
14
14
22
14
14
14
14
14
14
14
12
12
10
8
6
4
2
2
14
14
14
14
14
14
12
12
10
6
6
4
2
2
2
2
2
2
2
3.5
3.5
5.5
8
14
22
30
30
2
2
2
2
2
2
2
3.5
5.5
8
8
14
14
14
14
14
14
14
14
12
12
10
8
6
4
2
2
14
14
14
14
14
14
14
12
10
8
8
6
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
5.5
5.5
14
14
22
22
2
2
2
2
2
2
3.5
3.5
8
8
14
14
12
12
12
12
12
12
12
12
12
10
10
6
6
4
4
14
14
14
14
14
14
12
12
8
8
6
6
• 5.5kW~7.5kW (3 phase)
• 2.2~4.0kW (3 phase)
• 11~22kW (3 phase)
Wiring
Specifications for power terminal block wiring
R T B1 B1
B1
B1R(L1) S(L2) T(L3) P1(+) N(-)
B1
B1
R
R
RS
S
U U
U
U
U
U
B2 B2
B2
B2
B2
B2
T
T
T
V V
V
V
V
V
W W
W
W
W
W
13
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

3A 3B 3C P5 CM P6 P7 P8 VR V1 I AM
MO MG 24 P1 P2 CM P3 P4 S-S+
Multi-function input T/M 1-8
Common terminal
Power supply for external
potentiometer
Input terminal for voltage operation
Input terminal for current operation
Multi-function analog output terminal
Multi-function terminal for open collector
Ground terminal for external power supply
24V external power supply
Multi-function relay output A contact
Multi-function relay output B contact
Common for multi-function relays
Description Screw size
Single wire Stranded Torque (Nm) Specification
P1~P8
CM
VR
V1
I
AM
MO
MG
24
3A
3B
3C
1) Use the recommended tightening torque when securing terminal screws.
※When you use external power supply (24V) for multi-function input terminal (P1~P8), apply voltage higher than 12V to activate.
※Tie the control wires more than 15cm away from the control terminals. Otherwise, it interferes front cover reinstallation.
Terminal Wire size (mm
2
)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
Output voltage: 12V
Max. output current: 100mA
Potentiometer: 1~5kohm
Max. input voltage:
-12V~+12V input
0~20mA input
Internal resistor: 500ohm
Max. output voltage: 11V
Max. output current: 100mA
Below DC 26V,100mA
Max. output current: 100mA
Below AC 250V, 1A
Below DC 30V, 1A
1)
iG5A
Terminal Configuration
Control terminal specifications
14

Display Term
Run key
STOP/RESET key
Up key
Down key
Right key
Left key
Enter key
Forward run
Reverse run
Run key
Setting
RUN
STOP/RESET
▲
▼
▶
◀
●
FWD
REV
RUN
SET
KEY
LED
Description
Run command
STOP
: Stop command during operation,
RESET
: Reset command when a fault occurs.
Used to scroll through codes or increase parameter value
Used to scroll through codes or decrease parameter value
Used to jump to other parameter groups or move a cursor to
the right to change the parameter value
Used to jump to other parameter groups or move a cursor to
the left to change the parameter value
Used to set the parameter value or save the changed parameter value
Lit during forward run
Lit during reverse run
Lit during operation
Lit during parameter setting
Dimensions
95
ENT
SET FWD
REV
STOP
RESET
RUN
RUN
36.2
72.4
65.6 3.4
2-Φ4.5
83
513.9
2.1 23.1
70
C
L
1)
1) 4 LEDs above are set to blink when a fault occurs.
Keypad Features
15
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

Moving to other groups
Parameter group
Moving to other groups using the Right (
▶ ) key Moving to other groups using the Left ( ◀ ) key
Description
Drive group
Function group 1
Function group 2
I/O (Input/Output) group
Basic parameters necessary for the drive to run. Parameters such as Target frequency, Accel/Decel time settable.
Basic function parameters to adjust output frequency and voltage.
Advanced function parameters to set parameters for such as PID Operation and second motor operation.
Parameters necessary to make up a sequence using multi-function input/output terminal.
1) Target frequency can be set at 0.0 (the 1st code of drive group). Even though the preset value is 0.0, it is user-settable.
The changed frequency will be displayed after it is changed.
1) 1)
There are 4 different parameter groups in iG5A series as shown below.
iG5A
Moving to Other Groups
Parameter groups
16

When changing ACC time from 5.0 sec to 16.0 sec
• In the first code “ 0.00 ” , press the Up (▲) key once to go to the second code.
• ACC [Accel time] is displayed.
• Press the Ent (●) key once.
• Preset value is 5.0, and the cursor is in the digit 0.
• Press the Left (◀) key once to move the cursor to the left.
• The digit 5 in 5.0 is active. Then press the Up (▲) key once.
• The value is increased to 6.0
• Press the Left (◀) key to move the cursor to the left.
• 0.60 is displayed. The first 0 in 0.60 is active.
• Press the Up (▲) key once.
• 16.0 is set.
• Press the Ent (●) key once.
• 16.0 is blinking.
• Press the Ent (●) key once again to return to the parameter name.
• ACC is displayed. Accel time is changed from 5.0 to 16.0 sec.
1
2
3
4
5
6
7
8
Code change in Drive group
• In the 1st code in Drive group “0.00”,
press the Up (▲) key once.
• The 2nd code in Drive group “ACC”is displayed.
• Press the Up (▲) key once.
• The 3rd code “dEC”in Drive group is displayed.
• Keep pressing the Up (▲) key until the last code appears.
• The last code in Drive group “drC”is displayed.
• Press the Up (▲) key again.
• Return to the first code of Drive group.
• Use Down (▼) key for the opposite order.
1
2
3
4
5
1)
1) Pressing the Left (◀)/Right (▶)/Up (▲)/Down (▼) key while a cursor is blinking will cancel the parameter value change.
Pressing the Ent (●) key in this status will enter the value into memory.
※In step 7, pressing the Left (◀) or Right (▶) key while 16.0 is blinking will disable the setting.
17
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

Operation condition
1. Please make sure that R, S, T are connected to 3 phase AC input, and
U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step among
Low, Middle, and High.
3. If P1 (FX) turns on, the motor operates in forward. And after turning off,
it stops according to the deceleration time.
4. If P2 (RX) turns on, the motor operates in reverse. And after turning off,
it stops according to the deceleration time.
Operation command:
Run/Stop via FX/RX
Max. frequency change:
From 60Hz to 80Hz
Frequency command:
Multi-step operation [Low (20), Middle (30), High (80)]
P1 (Forward)
P2 (Reverse)
P6 (Low)
P7 (Middle)
P8 (High)
CM
Step Command After changeDefault
Code Description
1
2
3
4
5
6
F21
st1
st2
I30
I17
I18
Max. frequency change (FU1)
Multi-step frequency (DRV)
Multi-step frequency (DRV)
Multi-step frequency (I/O)
Forward run (P1: FX)
Reverse run (P2: RX)
Change Max. frequency.
Set ‛Low’step.
Set ‛Middle’step.
Set ‛High’step.
The default is FX. This value may change.
The default is RX. This value may change.
60Hz
10Hz
20Hz
30Hz
FX
RX
80Hz
20Hz
30Hz
80Hz
FX
RX
S1
S2
S3
S4
S5
Multi-step operation + Run/Stop via FX/RX + Max. frequency change
Wiring
Parameter setting
P1 (Forward)
P2 (Reverse)
P6 (Low)
P7 (Middle)
P8 (High)
CM
R
S
T
G
VR
V1
CM
U
V
W
S / W
3 phase
AC input
iG5A
Trial Run
18

1. Please make sure that R, S, T are connected to 3 phase AC input,
and U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step
among Low, Middle, and High.
3. If P1 (FX) turns on, the motor operates in forward. And after
turning off, it stops according to the deceleration time.
4. If P2 (RX) turns on, the motor operates in reverse. And after
turning off, it stops according to the deceleration time.
5. Control the motorʼs speed via potentiometer.
Operation command:
Run/Stop via FX/RX
Frequency command:
0~60Hz analog input via potentiometer
Accel/Decel time:
Accel-10sec, Decel-20sec
Operation condition
P1 (FX) Forward
P2 (RX) Reverse
CM
VR
V1
CM
Potentiometer
1~5kohm, 1/2W
R
S
T
G
U
V
W
3 phase
AC input
Motor
0~60Hz
Potentiometer 1~5kohm, 1/2W
VR
V1
CM
1
2
3
Wiring
Potentiometer (Volume) + Run/Stop via FX/RX + Accel/Decel time change
Step Command After changeDefaultCode Description
1
2
3
4
5
Drv
Frq
I17
I18
Analog input
(DRV group)
Accel/Decel time
(DRV group)
Forward run
(P1: FX)
Reverse run
(P2: RX)
Operation command
(DRV group) Turn on/off motor via terminal.
Change keypad command to analog voltage command.
Set Accel time to 10sec in ACC
Set Decel time to 20sec in dEC.
The default is FX. This value may change
The default is RX. This value may change.
1 (FX/RX-1)
0 (Keypad-1)
5sec (Accel)
10sec (Decel)
FX
RX
1 (FX/RX-1)
3 (V1: 0~10V)
10sec (Accel)
20sec (Decel)
FX
RX
Parameter setting
ACC
dEC
19
Compact & Powerful Drive iG5A
Drive Starvert iG5A Series

SV004IG5A-2
SV008IG5A-2
SV004IG5A-4
SV008IG5A-4
0.4
0.75
0.4
0.75
70
70
70
70
65.5
65.5
65.5
65.5
128
128
128
128
119
119
119
119
130
130
130
130
4.0
4.0
4.0
4.0
4.5
4.5
4.5
4.5
4.0
4.0
4.0
4.0
0.76
0.77
0.76
0.77
mm (inches)
mm (inches)
SV004iG5A-2 / SV008iG5A-2, SV004iG5A-4 / SV008iG5A-4
SV015iG5A-2 / SV015iG5A-4
SV015IG5A-2
SV015IG5A-4
1.5
1.5
100
100
95.5
95.5
128
128
120
120
130
130
4.5
4.5
4.5
4.5
4.5
4.5
1.12
1.12
W
W
W1
W1
A
A1
H1
H
D
B
D
H
W1
W1
B
Φ
Φ
A
A
H1
Drive model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ΦA (mm) B (mm) (kg)
Drive model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ΦA (mm) B (mm) (kg)
iG5A
Dimensions
20