LSK CRF1100-OFFROAD-DONGLE User manual

CRF1100-OFFROAD-DONGLE
CRF1100-OFFROAD-DONGLE
INSTALLATION MANUAL

2
Table of Contents
Basic information 3
Technical specification 3
Installation 4
Dongle control 6
Warranty 7
Safety notice 8
Troubleshooting 9
Recycling 10

3
Thank you for choosing our products. We strongly advise you
to read this user manual thoroughly. It contains important
instructions about installation, setup and use of the offroad
Dongle.
Basic information
Dongle eliminates the need of the annoying and time-consuming switching OFF
the Rear ABS, Traction Control and Wheelie Control when you riding in hard
offroad by taking control and forcing its own settings to ECU. This Dongle allows to
turn these electronic assistants ON/OFF with just one click on the keyboard.
Dongle also automatically clicks-off the safety message displayed after start of the
bike.
Technical specification
Energy consumption: 2W
Fuse: Internal self-resettable fuse (not changeable)
Working temperature: -30°C to +90°C
Dimensions: 25 x 28 x 12.5mm
-Device doesn’t lose its memory (when the memory function is turned ON by
user) after being disconnected from power.
-Device is shockproof and waterproof.

4
Installation
For detailed installation steps please follow the video
manual in this link. Please, scan it with QR code reader
app or continue to product website:
https://www.lskelectronics.com/store/Honda-CRF1100-
Africa-Twin-Offroad-Dongle-p592154121
1.Remove the left-side fuel tank cover.
2.Locate 4pin sealed connector and plug the Dongle in
between.

5
3.Locate 2pin sealed connector of the 12V car plug power
connector and plug Dongle in between.
4.Arrange the Dongle and wires.
5.Try the proper function of the Dongle.
If you see the “engine check”light indicator on the dashboard, do not worry. It is
because you have just disconnected the dashboard. It will disappear after ca three
cycles of starting the bike, riding few kilometers and turning the bike OFF.
6.Install the left-side fuel tank cover back.

6
*
˄
Dongle control
For detailed installation steps please follow the video
manual in this link. Please, scan it with QR code reader
app or continue to product website:
https://www.youtube.com/watch?v=LeqG3aNOpaA
Dongle is controlled using the OEM keyboard panel on the left handlebar.
1.Star button
Press and hold for min. 0.5s for turning ON/OFF:
-Rear ABS (+ Front ABS set to Offroad mode)
-Traction control
-Wheelie control
•Briefly release the throttle to complete traction control shutdown.
•Briefly stop moving the bike to complete the ABS shutdown.
•The status of the electronic systems is indicated by corresponding indicator
lights on the dashboard
•Flashing “T”round icon on the upper dashboard means that the dashboard has
no control over traction control settings (it is handled by the Dongle).
•Short click on the button is not handled by Dongle –its function is the same as
before installing the Dongle.
2.Up arrow button
Press and hold for min. 5s for turning ON the Dongle memory:
-Dongle will keep its settings after shutdown the bike.
•Successful setting is indicated by a short, rapid flashing of the Traction control
indicator light.
•Short click on the button is not handled by Dongle –its function is the same as
before installing the Dongle.
•Please be careful with using the memory function. Electronics assistants can
remain OFF when you or anyone else sits on the bike. It is on your own
responsibility.

7
˅
3.Down arrow button
Press and hold for min. 5s for turning OFF the Dongle memory:
-Dongle will be disabled (will not modify any motorcycle
settings) after every new start of the motorcycle.
•Successful setting is indicated by a short, rapid flashing of the Traction control
indicator light.
•Short click on the button is not handled by Dongle –its function is the same as
before installing the Dongle.
Warranty
Product is covered by 2 years Limited Warranty (from the date of purchase).
Limited Warranty covers any defects in material or manufacturing defects under
normal use and maintenance. We reserve the right not to accept the claim in the
case of mechanical damage that could be related to the defect of the product or
if the product was disassembled by unauthorized service.
This limited warranty also does not cover any problem that is caused by
conditions, malfunctions or damage not resulting from defects in material or
workmanship.
During warranty period, we will repair or replace defective product or defective
parts. To obtain warranty service, you must first contact us using claim form at
https://www.lskelectronics.com/claim to determine the problem and the most
appropriate solution for you.

8
Safety notice
a) Installation
This device should be installed by specialized garage or service. Inappropriate
mounting or electrical connection may result in damaging this or any other
electrical devices in the motorcycle. Improper installation of electronic devices can
lead to a fire resulting in damage the motorcycle and the owner’s health.
b) Small parts
Device contains small parts –keep away from children.
c) Road-use approval
Device is not approved for use at public roads. You use it at your own risk and
responsibility.
d) Legal
This device does nothing more than what can be set by hand on the original
instrument panel (It just combines all the procedure to one click). But even in this
case and even if the device is in deactivated state, it still interferes with other
onboard electronics systems that was originally tested and approved for road-use
without this device. The motorcycle is not approved for use on public roads if this
device is installed.
e) Safety
This device interferes with other onboard electronics systems even if it is in
disabled state. In case of its failure some safety systems can be unavailable. By
installing this device, you assume all responsibility for possible damage to health
and property caused by the incorrect function of this device and the subsequent
malfunction of other electronic systems of the motorcycle.
f) Using this device
Please be careful during all riding and especially when you turn OFF the electronic
assistants. Turn them OFF only when you really know what you are doing!
Turning Rear ABS OFF causes switching the Front ABS to the Offroad mode. In
Offroad mode the Front ABS is less sensitive. Please, keep that on mind when you
decide to activate the Dongle!

9
Troubleshooting
If you obey all the instructions, this Dongle should work properly without
problems. In case of any problems, feel free to contact us.
1.Many things on the dashboard screen are flashing. It is not
showing fuel level, actual gear and other stuff
Communication trough the Dongle failed. Please check the Dongle connectors and
wires and test the Dongle if it is working well.
-Check wires of the Dongle.
-Check the LED on the Dongle. It must turn ON for a short moment after start
the keyswitch and then go OFF. It symbolizes that the communication with ECU
is working.
oLED is still OFF -> Dongle does not have power or Dongle failed. Check the
2pin connectors and wires.
oLED is still ON -> communication is not working or Dongle failed. Check
the 4pin connectors and wires.
-Try Dongle autotest function
oConnect the both 4pin connectors of the Dongle one into another. Two
pin connectors are for power supply. Connect +12V to the RED one and
GND to the BLACK one. Or let it connected to the bike.
oStart the power and look at the status LED on the Dongle. Dongle confirm
establishing communication between both cables by few times flash of
the LED. If the LED is still ON or OFF, the Dongle is not working properly or
there is some problem with wiring.
2.Yellow “Engine check”control light is ON
This happens after disconnecting the dashboard 4pin connector and it is normal
after installation of the Dongle. Motorcycle needs ca 3-4 cycles of starting the
bike, riding few kilometers and turning the bike OFF to checking that everything is
working well again. Then the ECU turns the engine check control light OFF.
If nothing helps, contact us using claim form at
https://www.lskelectronics.com/claim

10
Recycling
Retired device should be given to places specified for retrieving electrical garbage.
Package should be thrown into a specific container for recycled garbage.
Device meets RoHS Directive.
www.lskelectronics.com
[email protected]
Product website: