Lucci LEDlux 290998 User manual

Installation Instructions
1 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
Lucci LEDlux – Electronic LED Dimmer
SKU# 290998
Rated Voltage 220-240V~ 50/60Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before using the product. Please keep instructions for future reference.
Warranty
•This Electronic Dimmer is covered by a 12 month warranty. The warranty is from date of purchase, not the date of
installation.
•If the Electronic Dimmer is not assembled and installed by a licensed electrician the warranty will be void.
•Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
•Warranty will be void if there is any damage due to improper usage or modification to the Electronic Dimmer.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation Requirements
•Must be installed by a licensed electrician and in accordance to AS/NZS3000 (the latest edition).
•This LEDlux LED Dimmer is designed for use with LEDlux brand family dimmable LED lighting equipment.
Where the loads are on the same electrical circuit, it must be Mains 240V dimmable LED retrofit luminaries
which have a dimmable LED driver. (Note: A dimmable electronic transformer is not considered to be a
dimmable LED Driver).
•Problems encountered when using other types of dimmable 240V luminaires NOT recommended in this
installation guideline are NOT covered by the Lucci LEDlux guarantee.
•Do not exceed the rated output load listed below:
- For Mains 240V LEDlux dimmable LED globes and downlights: Max. 200W;
- For Mains Halogen globes: Max. 200W;
- ELV halogen with dimmable transformer: Max. 200W
•Not suitable for use with ferromagnetic transformers.
•Do not exceed rated power input specification.
•This product is suitable for indoor use only.
Installation Preparation
Before carrying out the installation the following must be considered.
-Wall plate or wall mounting box (not supplied) will be required for installation pending on where the dimmer will be
located e.g. behind a wall or surface mounted.
-A wall switch is required (not supplied) when using with this dimmer to provide ON/OFF and isolation to the
electrical lighting equipment circuit. The dimmer MUST not be used as an ON/OFF switching device. Only use as
a dimmer.
-Ensure the power to the electrical circuit is switched OFF.
-All electrical wiring connection & disconnection must be in accordance with Australian & New Zealand wiring rules
e.g. AS/NZS 3000 (the latest edition).
CAUTION: For your safety, this LEDlux LED electronic dimmer must be installed by a licensed electrician.

Installation Instructions
2 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
Installation Directions
WARNING – HIGH VOLTAGE
-For your safety: Power to the circuit must be disconnected or switched off.
-Household power can cause SERIOUS INJURY or DEATH.
- Wiring must meet all local and national electrical wiring codes.
MAKING THE ELECTRICAL CONNECTIONS (see Fig.1)
1. Disconnect electrical power from the working circuit.
2. Connect 240V ~ mains L to Lof the dimmer.
3. Connect of the dimmer to the LOAD.
4. Connect the LOAD N to the 240V~ mains N.
5. Optional - adjust the variable resistor to optimize the dimming range for the connected LED LOAD.
(Note: More LED type LOADs can be connected in series, up to the maximum allowable per LOAD type outline in
the “installation requirements” section of this manual.)
Note: An isolation wall switch must be included in the wiring installation. The switch allows disconnecting of
the dimmer and loads from the mains 240VAC power during maintenance and cleaning of the LED lighting
equipment.
FIGURE 1. Wiring Diagram
Wiring Diagram
Wiring Diagram
Variable
Resistor
NOTE: The Variable Resistor on the LEDlux LED Dimmer allows correcting
and maximizing dimming range when using the LEDlux Dimmable LED
product range from Beacon Lighting. Turn clockwise to reduce the lowest
dimming level, turn anti-clockwise to increase the lowest dimming level.

Installation Instructions
3 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
ON / OFF
– Press and release the dial to turn the dimmer ON or OFF.
DIMMING
- Turn the dial clockwise or anti-clockwise to dim up or down.
Operation
Switch Plate:
CLIPSAL
Saturn
Series
Switch Plate:
HPM Excel & Linea
Series,
CLIPSAL C2000 & 2000 Series
Original Dial
Original Dial with
extended notch
FIGURE 2. Dials application

Installation Instructions
4 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
Specifications
SKU# 290998
Specification – Dimmer Input:
Model # KDT-200IA-4
Rated Voltage 220-240V AC
Frequency 50/60 Hz
Specification – Dimmer Output
LEDlux Dimmable LED Luminaires, Downlights, and globes
(Mains 240V type only)
Max. 200W
HV – halogen Max. 200W
ELV Converter / Transformer
(With halogen load only) Max. 200W

Installation Instructions
5 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
Trouble shooting
SYMPTOMS PROBABLE CAUSES SUGGESTED REMEDY
1. The dimmer is not
operating.
The Switch on the dimmer circuit
has been turned OFF.
1) Check the switch to the dimmer circuit and
switch ON.
Mains power is not restored to
lighting circuit & dimmer.
1) Replace the fuse or turn ON circuit breaker at
the switchbox.
2. The Lamps /
Luminaires flickers when
dimmer is at maximum or
minimum.
The LEDlux LED load does not
receive enough electrical
voltage/current because: 1)
Minimum/Maximum loading on
the dimmer circuit is not met,
and flickering can occur while
dimming at minimum or
maximum.
Increase/remove the loading by
adding/removing more LEDlux LED product
onto the same dimming circuit, so that the
dimmer load is within specification. Refer to
technical specification.
2) At minimum setting the
dimmer circuit provides very little
voltage/current.
Adjust the variable resistor on the LED dimmer,
to adjust the voltage/current input into the
dimming circuit until the LED stops flickering.
This may reduce the dimming range, but offer
LED light performance stability. Note: This task
can only be performed by a licensed electrician.
3. Dimming range is not
good. Cannot dim LED
load to 0% / zero light.
All LEDlux dimmable LED
drivers are different in
specification. The LEDlux
dimmer has a variable resistor to
adjust the input voltage/current
into the dimming circuit with the
variable resistor which can allow
dimming to 0%, or near 0%.
Adjust the variable resistor. This will improve
the dimming range to zero or near zero LED
light output of the dimmable LED luminaire. LED
performance may reduce slightly; however, the
dimming range is improved. Note: This task can
only be performed by a licensed electrician.
Compatibility issues - other
dimmable LED drivers may not
be compatible to dim to near
zero.
Adjust the variable resistor. This will improve
the dimming range, however, may not achieve
zero % dimming.
LED performance may reduce slightly; however,
the dimming range is improved. Note: This task
can only be performed by a licensed electrician.

Installation Instructions
6 | P a g e V e r s i o n 3 . 0 ( 2 0 1 9 / 0 8 )
Warranty
LUCCI WARRANTY DETAIL
LUCCI WARRANTY HOTLINE- 1800 602 243
In the event of service being required, please call the Lucci Warranty Hotline on 1800 602 243 between 9am & 5pm (EST) Monday to Friday. Please
make sure you have all the details filled out at the end of the manual in the section “WARRANTY INFORMATION” before making the call.
In addition to any warranty rights or conditions under statutory regulations, Lucci warrants all of its LED Dimmers against defective workmanship and
faulty materials for 12 months from the date of purchase. Lucci undertakes, at its option, to repair or replace, free of charge, each product or part
thereof on condition that;
1. The LEDlux LED Dimmer was installed correctly as outline in the installation manual;
2. The product was installed by a licensed electrical contractor.
3. LEDlux LED Dimmer has not been subjected to misuse, neglect, or been involved in an accident.
4. The repairs are not required as a result of normal wear and tear.
5. A copy of the original receipt of purchase is presented.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Lucci Design cannot be held responsible for any repair other than those carried out by it or one of its Authorised Service Agents. Please
keep this warranty information in a safe place. This information must be produced in the event of service being required.
LUCCI WARRANTY INFORMATION
LUCCI WARRANTY HOTLINE- 1800 602 243
Complete and retain this form for your personal records and warranty purposes.
NAME___________________________________________________________________________________________________
ADDRESS________________________________________________________________________________________________
____________________________________POSTCODE____________________________
MODEL NUMBER___________________________________________________________
(PO# + DATECODE Sticker here)
PO NUMBER or DATECODE__________________________________________________
DATE OF PURCHASE_______________________________________________________
INSTALLING LICENSED ELECTRICAN & LICENCE #______________________________________________________________
ATTACH PROOF OF PURCHASE HERE
COMPLETED DETAIL PAGE SHOULD BE PRODUCED AND SENT TO THE WHOLESALER OR THEIR AUTHORISED AGENTS BEFORE OBTAINING WARRANTY SERVICE.