Lucent Technologies PacketStar PSAX 1250 User manual

Doc. No.: 255-700-017
COMCODE: 300303252
PacketStar™
PSAX 1250 Access Concentrator
User Guide
A PacketStar™ PSAX Central Office Product
Issue 1, October 2000
System Softw re Rele se 6.3.0
AQueView™ EMS Softw re Rele se 4.4

Copyright © 2000 by Lucent Technologies. All rights reserved.
For trademark, regulatory compliance, and related legal in ormation,
see the "Copyright and Legal Notices" section.

255-700-017 iii
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Copyright and egal Notices
Copyright
Copyright © 2000 by Lucent Technologies. All rights reserved.
This material is protected by the copyright laws o the United States and
other countries. It may not be reproduced, distributed, or altered in any
ashion by any entity (either internal or external to Lucent Technologies),
except in accordance with applicable agreements, contracts or licensing,
without the express written consent o the InterNetworking Systems, Access
Technology organization and the business management owner o the
material.
This document was prepared by the In ormation Design and Development
department o Lucent Technologies, InterNetworking Systems, Access
Technology group. O ices are located in Landover, Maryland, U.S.A.
Trademarks
AQueView, PacketStar, Lucent, Lucent Technolo ies, and the Lucent Technologies
logo are trademarks o Lucent Technologies in the U.S.A. Other product and
brand names mentioned in this guide are trademarks or registered
trademarks o their respective owners.
Warranty Information
Software and Hardware imited Warranties
Lucent Technologies provides a 90-day limited so tware warranty, and a one-
year limited hardware warranty on this product. Re er to the Software License
and Limited Warranty A reement and the Lucent Technolo ies InterNetworkin
Systems Global Warranty that accompanied your package or more
in ormation.
Every e ort has been made to ensure that this document is complete and
accurate at the time o release, but in ormation is subject to change. Lucent
Technologies assumes no responsibility or liability or errors or inaccuracies
that may appear in this guide.

Copyright and egal Notices
W rr nty Inform tion
iv 255-700-017
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Warranty Warnings
!CAUTION:
Do not make electrical or mechanical modifications to any of the
components in the PSAX system. ucent Technologies is not responsible
for the safety or the performance of a modified ucent product. Do not
attempt to repair any failed Power Supply module, Stratum 3–4 module,
CPU module, I/O, or Server module.
!CAUTION:
Do not make electrical or mechanical modifications to any of the
components in the PSAX system. ucent Technologies is not responsible
for the safety or the performance of a modified ucent product. Do not
attempt to repair any failed removable I/O or server modules.
!CAUTION:
Modifying or tampering with PSAX chassis components may void your
warranty. Any modification to this equipment not expressly authorized
by ucent Technologies may void your granted authority to operate such
equipment.
!CAUTION:
Air vents in the PSAX chassis are provided to aid in ventilation and to
protect from overheating. These vents must be regularly inspected by
the user and cleared of dust and blockage. Equipment failure associated
with improper maintenance or suspected failure to adhere to proper
ventilation procedures as described above will void your warranty.
!CAUTION:
You must replace an air filter having an accumulation of dust to ensure
adequate airflow through the PSAX chassis. Reduced airflow could result
in damaging heat buildup within the chassis.
• Periodically inspect the air filter for accumulated dust and replace the
filter as needed. At a minimum, monthly inspection is recommended.
Equipment failure due to inadequate airflow voids your equipment
warranty.
• Use only filters supplied by ucent Technologies in your PSAX chassis.
Use of other filters voids your equipment warranty.
!CAUTION:
You must maintain a minimum 10.16 cm (4 in.) of clearance around the
chassis for adequate airflow. Failure to adhere to this space requirement
may result in equipment failure due to overheating. Failure to provide a
minimum of 10.16 cm (4 in.) of clearance between this unit and any other
device/structure will void your warranty.

255-700-017 v
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Copyright and egal Notices
Regul tory St nd rds Compli nce
!CAUTION:
If your system or location loses power or your current session ends
abnormally while you are in the process of configuring the system, and
you have not yet saved the values permanently, you will lose all unsaved
values you have applied on the various windows.
!CAUTION:
Shipping the chassis with removable modules installed may cause
damage to the chassis and the modules. Damage to any of the
components in the system resulting from shipping the chassis with
removable modules installed could void your warranty. Only ucent-
authorized personnel should ship the PSAX 1250 chassis with a module
installed.
Regulatory Standards Compliance
The PSAX 1250 Access Concentrator is ully compliant with the ollowing
environmental, sa ety, and emissions standards. Appropriate statements
appear in the next subsection.
Safety Requirements
•Underwriter’s Laboratory (UL) — Sa ety and Factory Compliance
UL 1950
•CB-Scheme — IEC 60950:1991+A1:1992+A2:1993+A3:1995+A4:1996
Electromagnetic Compatibility (EMC) and Physical Requirements
•Federal Communications Commission (FCC) — EMC compliance
(Part 15 Class A)
•Network Equipment Building System (NEBS) GR-63-CORE and
GR-1089-CORE, Level 3 requirements
•EN 55022:1994 Class A (CISPR22:1993)
•EN 50082-1:1992
•VCCI Class A
CE Marking
CE marking o the Lucent Technologies PSAX 1250 ATM Access
Concentrator consisting o the ollowing model numbers:

Copyright and egal Notices
Regul tory St tements
vi 255-700-017
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
20S00, 20S10, 20P01, 20P02, 20P03, 20P04, 20P05, 20P06, 20P09, 20P10,
20P11, 20P12, 20P13, 20P14, 20P15, 20P16, 20P17, 20P18, 20P20, 20P21,
20P22, 20P23, 20A04, 20A09, 20A12, 20A13, 20A14, 20N01, 20N05, 21N05,
20N11, 20N07, 20N16, 20N20, 20N22, 20N27, 20N28, 20N29, 20N34,
20N40, 20N41, 20N56, 20N62, 20N63, 20N64, 20N65, 20N92, 20N93,
23N27, 23N66
is based upon con ormity with the ollowing standard(s) or other normative
document(s):
•EN 55022:1994 Class A
•EN 50082-1:1992
•EN 60950:1992+A1:1993+A2:1993+A3:1995+A4:1997+A11:1997
•CTR 4/A1 as speci ied in Commission Decision 98/520/EC
•CTR 12/A1 as speci ied in Commission Decision 97/520/EC
•CTR 13 as speci ied in Commission Decision 97/521/EC
•CTR 24 as speci ied in Commission Decision 97/639/EC
in accordance with the provisions o the ollowing Council directives:
•Electromagnetic Compatibility (EMC) 89/336/EEC
•Low Voltage 73/23/EEC
•Telecommunications Terminal Equipment and Satellite Earth Station
Directive 98/13/EC
The European Community Declarations o Con ormity or the PSAX 1250
Access Concentrator are included in the EC Declarations o Con ormity
Appendix in the back o this guide.
Regulatory Statements
United States Federal Communications Commission (FCC) Statements
Part 15. This equipment has been tested and ound to comply with the
limits or a Class A digital device, pursuant to Part 15 o the FCC rules. These
limits are designed to provide reasonable protection against harm ul
inter erence when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio requency energy, and,
i not installed and used in accordance with this guide, may cause harm ul
inter erence to radio communications. Operation o this equipment in a

255-700-017 vii
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Copyright and egal Notices
Regul tory St tements
residential area is likely to cause harm ul inter erence; in this case, you
would be required to correct the inter erence at your own expense.
All cables used to connect to peripherals must be shielded and grounded.
Operation with cables, connected to peripherals, that are not shielded and
grounded may result in inter erence to radio and television reception.
The user is cautioned that any changes or modi ications not expressly
approved by the party responsible or compliance could void the user’s
authority to operate the equipment.
Part 68. This equipment complies with Part 68 o the FCC rules. On the
back o the PSAX 1250 chassis is a label that contains the FCC registration
number, in addition to other in ormation. You must provide this in ormation
to the telephone company, i they request it. The FCC requires Lucent
Technologies, Inc., to provide you with the ollowing in ormation:
1. The PSAX 1250 system has digital service inter ace capabilities using RJ-
48C and RJ-48H connectors. The acility inter ace codes with which the
PSAX 1250 system complies or digital services are as ollows: 04DU9-
BN, 04DU9-DN, 04DU9-1KN, and 04DU9-1SN. The PSAX 1250 system
has loop start inter ace capabilities using an RJ-11C connector. The
acility inter ace code with which the PSAX 1250 system complies or
service is 02LS2. The service order codes or the PSAX 1250 system are
6.0F or the T-1 inter ace and 9.0Y or the loop start inter ace.
2. An FCC-compliant telephone network inter ace jack is built into this
equipment and is compatible with interconnections that are Part 68
compliant.
3. The REN or the Voice 2-Wire O ice module when used in the
PSAX 1250 system is 0.7B.
4. I the PSAX 1250 system causes harm to the telephone network, the
telephone company will noti y you in advance that temporary
discontinuance o service might be required. But i advance notice is not
practical, the telephone company will noti y you as soon as possible.
Also, you will be advised o your right to ile a complaint with the FCC i
you believe this is necessary.
5. The telephone company might make changes in its acilities, equipment,
operations, or procedures that could a ect the operation o this
equipment. I this happens, the telephone company will provide
advance notice or you to make necessary modi ications to maintain
uninterrupted service.
6. I you experience trouble with the PSAX 1250 system, or need repairs or
warranty in ormation, please re er to the Limited Hardware Warranty
card that accompanied your PSAX 1250 product shipment or
instructions on obtaining technical support in your area.
I the PSAX 1250 system is causing harm to the telephone network, the
telephone company might request that you disconnect the equipment
until the problem is resolved.
7. This equipment has no user-serviceable parts.

Copyright and egal Notices
Regul tory St tements
viii 255-700-017
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
This equipment cannot be used on public coin telephone service provided by
the telephone company. Connection to party line service is subject to state
tari s. Contact your state public utility commission, public service
commission, or corporation commission or in ormation.
Canadian Regulatory Statements
Industry Canada
Information
Ringer Equivalence Number (REN) Notice. The Industry Canada label
identi ies certi ied equipment. This certi ication means that the equipment
meets certain telecommunications network protective, operational, and
sa ety requirements. The Department does not guarantee that the equipment
will operate to the user’s satis action.
Be ore installing this equipment, the user should ensure that it is permissible
to be connected to the acilities o the local telecommunications company.
The equipment must also be installed by using an acceptable method o
connection. In some cases, the company’s inside wiring associated with a
single-line individual service may be extended by means o a certi ied
connector assembly (telephone extension cord). The customer should be
aware that compliance with the above condition may not prevent
degradation o service in some situations.
Repairs to some certi ied equipment should be made by an authorized
maintenance acility designated by the supplier. Any repairs or alternations
made by the user to this equipment or equipment mal unctions might give
the telecommunications company cause to request the user to disconnect the
equipment.
For their own protection, users should ensure that the ground connections o
the power utility, telephone lines, and internal metallic water pipe system are
connected together. This precaution may be particularly important in rural
areas.
!CAUTION:
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority or
electrician.
The Ringer Equivalence Number (REN) assigned to the Voice 2-Wire O ice
module denotes the percentage o the total load to be connected to a
telephone loop, which is used by the device, to prevent overloading. The
termination on a loop may consist o any combination o devices subject only
to the requirement that the total o the REN o all devices does not exceed 5.
The REN or the Voice 2-Wire O ice module when used in the PSAX 1250
system is 0.7B.
Renseignements
Industrie Canada
Avis de nombre équivalent de sonneries (REN). Le label Industrie
Canada permet de reconnaître les équipements homologués. Cette

255-700-017 ix
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Copyright and egal Notices
Regul tory St tements
homologation indique que l’équipement satis ait certaines règles de
protection, d’exploitation et de sécurité des réseaux de télécommunications.
Le ministère de l’Industrie ne garantit pas que l’équipement onctionnera à la
satis action de l’utilisateur.
Avant d’installer cet équipement, l’utilisateur doit s’assurer qu’il est permis
de le connecter aux installations de la compagnie de télécommunications
locale. L’équipement doit également être connecté suivant une méthode
convenable. Dans certains cas, il sera nécessaire de prolonger le câblage
intérieur de la ligne d’abonné de la compagnie au moyen d’un connecteur
homologué (rallonge de téléphone). L’abonné doit savoir que, dans certaines
situations, la con ormité aux dispositions ci-dessus ne prévient pas
nécessairement la dégradation du service.
La réparation de certains équipements homologués doit être assurée par un
atelier agréé désigné par le ournisseur. Toute réparation ou altération
e ectuée par l’utilisateur ou tout mauvais onctionnement de cet
équipement peut donner à la compagnie de téléphone des raisons de
demander audit utilisateur de déconnecter celui-ci.
Pour leur propre sécurité, les utilisateurs doivent veiller à ce que les mises à
la terre de l’alimentation secteur, des lignes téléphoniques et du système
intérieur de conduites d’eau métalliques soient raccordés ensemble. Cette
précaution peut s’avérer particulièrement importante dans les zones rurales.
!CAUTION:
es utilisateurs ne doivent pas tenter d’effectuer eux-mêmes ces
raccordements, mais doivent prendre contact avec un électricien ou
organisme de vérification compétent.
Le nombre équivalent de sonnerie (REN) attribué au module central bi ilaire
(Voice 2-Wire O ice) correspond au pourcentage de la charge totale à
connecter à un circuit téléphonique bi ilaire; il est utilisé par l’appareil pour
prévenir la surcharge. Le circuit peut être terminé par n’importe quelle
combinaison d’appareils, à la seule condition que le total des REN de ces
derniers ne dépasse pas cinq.
International Regulatory Statements
ISPR22. This is a Class A product. In a domestic environment, this product
may cause radio inter erence, in which case the user may be required to take
adequate measures.
Australian/New Zealand Regulatory Statements
AS/NZS-3548 Warning. This is a Class A product. In a domestic
environment, this product may cause radio inter erence, in which case the
user may be required to take adequate measures.

Copyright and egal Notices
Regul tory St tements
x255-700-017
PacketStar™ PSAX 1250 User Guide, Issue 1 Rele se 6.3.0
Japanese Regulatory Statement
Voluntary ontrol ouncil (V I) lass A Regulatory Statement. This
is a Class A product based on the standard o the Voluntary Control Council
or Inter erence by In ormation Technology Equipment (VCCI). I this
equipment is used in a domestic environment, radio disturbance may occur,
in which case, the user may be required to take corrective actions.