Luci QUICKIE Q500 M User manual

®
INSTALLATION GUIDE
QUICKIE Q500 M
®

2
INSTALLATION GUIDE
QUICKIE Q500 M
PACKAGE CONTENTSPACKAGE CONTENTS
A. Rear SmartFrame™ (1)
B. Left SmartFrame™ (1)
C. Right SmartFrame™ (1)
D. Scout (1)
E. Footplate Drill Guides (2)
F. Dashboard (1)
G. Dashboard Reference Card (2)
*Bracket based on order form:
H. LED Joystick Dashboard Bracket (1)
I. Color Joystick Dashboard Bracket (1)
J. Color Joystick Spacer (1)
K. CJSM 1/2 Dashboard Bracket (1)
L. OMNI Dashboard Bracket (1)
M. Headlight Hardware Kit (1)
N. Alcohol Wipe (2)
O. LuciLink™ Hub & Wheelchair Key™ (1)
P. 1/4” Drill Bit (1)
Q. 5/16” Drill Bit (1)
R. M6 x 30mm Socket Head Bolt (4)
S. M8 x 16mm Low Profile Socket Cap Screw (4)
T. M5 x 16mm Hex Head Screw (2)
U. M5 x 14mm Phillips Head Screw (1)
V. M5 x 8mm Hex Head Screw (2)
W. M5 x 8mm Phillips Head Screw (3)
X. 4-40 x 3/16 Phillips Head Screw (4)
Y. M5 Nylon Insert Locknut (1)
Z. #10 Washer (2)
AA. Zip Ties (18 short, 8 long)
AB. Cable Clips (6)
AC. User Manual (1)
®
You will also need:
• 3mm Allen Wrench
• 5mm Allen Wrench
• 13mm Wrench
• 8mm Socket Wrench
• Phillips P1 Screwdriver
• Masking Tape
• Drill
• Zip Tie Cutter

3
A
B C
Copyright © 2021 LUCI. All Rights Reserved.
N
M
Headlight
Hardware
Kit
KJI
™QUICKIE SINGLE FOOTPLATE
DRILL GUIDE
Tear this template along the perforated lines.
Line up the green edges with the edges of the
footplate as shown in the image below. Securely
tape this template to the footplate. Ensure that it
does not shift while the holes are drilled.
Copyright©2021 LUCI,
AllRights Reserved.
P002-049Version 1.0
Allproduct names, brands,
andtrademarks are property
oftheir respective owners. All
company,product, and service
namesused in this website are
foridentification purposes only.
Useof these names, trademarks,
andbrands does not imply
endorsement.
Formore information visit
luci.com/patents.
Use 1/4 inch drillbit
for this hole
Use 5/16 inch drillbit
for these two holes
D
H L
E
G
F
OP
Q
LUCI
MANUAL
R S T U V W X Y Z
AA AB
AC

4

5
STEP 1 - PREPARE WHEELCHAIR BASE
INSTRUCTIONS
2
1
Use a 5 mm Allen wrench to loosen the two bolts in the back cover (Figure 1) and remove the
back cover. If the wheelchair has a seat elevator, turn the wheelchair on and raise the seat
completely to allow adequate room to work comfortably (Figure 2), then turn the wheelchair o.
Otherwise, remove the two thumbscrews under the front of the seating assembly and flip the
seating assembly back to open the battery compartment and gain adequate access (Figure 3).
Tools Required
- 5mm Allen Wrench
REMOVE
3

STEP 2 - SECURE SIDE SMARTFRAMES
Tools Required
- Rear SmartFrame™ (A)
- Left SmartFrame™ (B)
- Right SmartFrame™ (C)
- M6 × 30mm Bolts (R)
- 5mm Allen Wrench
6
Note: If the wheelchair has headlights, remove them to make room for the Side SmartFrames;
they will be reattached afterwards.
Using a 5mm Allen wrench, remove the bolts on the front and both sides of the front cover (Figure
4) and remove the front cover completely. Place the three parts of the SmartFrame (A, B and C)
on the floor around the wheelchair. Set the Left SmartFrame (B) on the left side of the chair where
the front cover was removed, lining up the bolt holes (Figure 5). Do not insert the bolts yet.
Note: There is a bolt that is located in between the tire and the tie-down hook on the side of
the wheelchair. This bolt will insert into the hole near the front of the bracket on the 90 degree
bend, holding the bracket in place.
Repeat the process on the right side of the wheelchair: set the Right SmartFrame (C) on the right
side of the wheelchair, slotting it onto the bolt between the tire and the tie down. Replace the
front cover onto the chair. Loosely insert four M6 x 30mm bolts (R), two on each side, securing
the Left and Right SmartFrames between the wheelchair and front cover (Figure 6). Reinsert the
two original screws in the front of the front cover and tighten all bolts and screws.
5
6
4
REMOVE

7
STEP 2B - REATTACH HEADLIGHTS OPTIONAL
Tools Required
- Headlight Kit (M):
- M4×30mm Screw (2)
- Rubber Washer (2)
Note: If the wheelchair has headlights, reattach them now.
Using the contents of the Headlight Kit (M), slide a rubber washer onto the threaded stud. Insert
the M4 x 30mm screw into the headlight and attach the headlight to the SmartFrame (Figure 7).
Repeat on the other side.
7Right Side Shown
M4x30mm Screw
Rubber Washer

REMOVE REFLECTOR
8
STEP 3 - CONNECT LUCI TO THE WHEELCHAIR
If the battery compartment was opened, flip the seating assembly back into place and reinsert
the thumbscrews that hold the seating assembly in place.
Remove one reflector from the rear cover by rotating the tabs on the inside and pushing the
reflector out (Figure 8). Route the two R-NET cables from the Rear SmartFrame (A) through
the opening in the rear cover (Figure 9). On the back of the wheelchair, unplug the main R-NETR-NET
cable on the far left (Figure 10) and plug it into the female R-NET cable end on LUCI. Plug the
male R-NET cable end from LUCI into the main wheelchair R-NET outlet on the far left (Figure
11). Turn the wheelchair on to ensure all power cables have been properly connected. Turn o the
wheelchair.
Tools Required
- Rear SmartFrame™ (A)
8
10
UNPLUG R-NET
9
11
CONNECT LUCI
RNET cable

REAR
CENTER BUBBLE TO
LEVEL SMARTFRAME
REMOVE AND REPLACE ONE AT A TIME
IN THE ORDER SPECIFIED ABOVE
9
STEP 4 - SECURE THE REAR SMARTFRAME
Tools Required
- Rear SmartFrame (A)
- M8 × 16mm Screws (S)
- 5mm Allen Wrench
12
13
14 Make sure the bubble is between the lines on the
level taped to the SmartFrame and tighten all four
screws (Figure 14). The manufacturer recommends
25 N-m (18 ft-lb) of torque on these fasteners.
Remove the bubble level once the SmartFrame is
level and secure.
Use the 5mm Allen wrench to reattach the rear
cover on the wheelchair, using the original bolts
(Figure 12). On both sides of the wheelchair, remove
the forward-most bolt completely and then loosen
the rear bolt. Install the Rear SmartFrame (A) by
slotting it onto the rear bolts. Insert M8 x 16mm
Screws (S) into the front holes and tighten enough
to keep the SmartFrame from moving. Replace the
rear bolts with M8 x 16mm Screws (S) on both sides.

10
15B
STEP 5 - ATTACH SCOUT
Tools Required
- Scout (D)
- Footplate Drill Guides (E)
- Drill
- Phillips P1 Screwdriver
- 1/4” Drill Bit (P)
- 5/16” Drill Bit (Q)
- M5 × 14mm Screw (U)
- M5 × 8mm Screws (W)
- M5 Nylon Locknut (Y)
- #10 Washer (Z)
- 8mm Socket Wrench
Choose the correct Drill Guide (E) depending on the wheelchair’s footplate - Single Footplate or
Dual (Individual) Footplates - and tear it out along the perforated lines.
Single Footplate:
Line up the template as shown in the image on the Drill Guide and tape it to the footplate (Figure
15A). Drill the two larger holes with the 5/16” drill bit (Q) and the smaller hole with the 1/4” drill bit
(P) as marked on the template (Figure 16A). Place the Scout (D) on top of the footplate, aligning the
screw holes in the bracket with the drilled holes in the footplate. Place #10 Washers (AA) on two of
the M5 x 8mm Phillips Head Screws (W), raise the footplate and loosely insert the screws into the
5/16” holes from the bottom of the footplate (Figure 17A) to hold the Scout bracket in place. Insert
the M5 x 14mm Screw (U) into the 1/4” hole from the top of the footplate (Figure 18A). Use an 8mm
socket wrench to secure it from the bottom with the M5 Nylon Locknut (Z). Tighten all three screws.
Dual Footplates:
Line up the template as shown in the images on the Drill Guide and tape it to the footplate (Figure
15B). Note which slot on the template to line up with the footplate, depending on the footplate style.
Loosely insert one M5 x 8mm Phillips Head Screw (W) through the template and into the threaded
hole to help keep the template in place. Drill the two holes with the 5/16” drill bit (Q) as marked on
the template (Figure 16B). Remove the M5 x 8mm screw (W) and discard the template. Place the
Scout (D) on top of the footplate, aligning the screw holes in the bracket with the drilled holes in
the footplate. Loosely reinsert the M5 x 8mm Screw (W) into the threaded hole (Figure 17B). Raise
the footplate, place #10 Washers (Z) on the remaining two M5 x 8mm Phillips Head Screws (W)
and insert them into the 5/16” holes from the bottom of the footplate (Figure 18B). Tighten all three
screws.
15A