Lucky Star Physician Scale User manual

Professional Weighing
Equipment
Physician Scale
User Manual 2.0
Operation Manual
Manufactured by Lucky Star / Distributed by LW Measurements, LLC

Rev 2, 10.21.2016
2
Table of Contents
Section Page
Declaration of Conformity 3
Customer Service 4
Introduction 5
Safety 6
Weight Scale 7
Functions 8
Features 9
Application & Conformity 10
Getting Started 11
Delivery 11
Assembly & Installation 12-17
Operation 18-21
Trouble Shooting 22
Maintenance & Service 23
Transportation & Storage 23
Warranty 24

Rev 2, 10.21.2016
3
Declaration of Conformity
Declaration of conformity for apparatus with CE mark
We hereby declare that the product to which this declaration refers conforms to
the following standards.
Electronic scale: Physician Scale
USA model
UK (Europe) model
Physician
Scale
Mark applied
EU Directive
Standards
2004/108/EC
EN 61326-1: 2006
Signature:
Boon Lim, R & D Manager
Date: 04. 06. 2014
LW Measurements LLC, 620 Carlson Court, Rohnert Park, CA 94928

Rev 2, 10.21.2016
4
Customer Service
USA
LW Measurements LLC
620 Carlson Court
Rohnert Park, CA 94928
USA
Tel: [phone]
FAX: [phone]
http://lwmeasurements.com
EUROPE
LW Measurements Europe Ltd
Chalkwell Park House 700 London Road
Westcliff-on-Sea Essex SS0 9HQ
United Kingdom
Tel: [phone]
Fax: [phone]
http://lwmeasurements.com

Rev 2, 10.21.2016
5
Introduction
What you should know about these Operating Instructions:
Tree® Professional Weighing Equipment products are simple to operate.
Nevertheless, you should read through these operating instructions in their
entirety, so that you can make optimum use of the full potential and the diverse
possibilities of the weighing scale in your daily work.
These operating instructions contain guidance in the form of pictograms and
keyboard diagrams, which should help you in finding the required information:
For the labeling of potential hazards and advice, please see Safety below.

Rev 2, 10.21.2016
6
Safety
Representations and symbols
Important instructions, which involve safety, are highlighted with the appropriate mark:
Safety recommendations
When using the weighing equipment in surroundings with increased safety
requirements, the corresponding regulations must be observed.
The weighing scale may only be used with the power adapter supplied.
Before connecting the power adapter to the scale, the user must ensure that the
operating voltage stated on the power adapter is compliant with the mains voltage.
If not, please contact Customer Service at the address above.
If the power adapter or its cable is damaged, the weighing scale must immediately
be disconnected from the electricity supply (pull out the power adapter).
If there should be any reason to believe that it is no longer safe to operate the
scale, it should be immediately unplugged from the electricity supply (pull out
power adapter) and secured against inadvertent operation.
In carrying out maintenance work, it is essential to follow the recommendations set
out in maintenance and servicing.
The weighing scale must not be operated in an area subject to explosion risks.
Care must be taken when weighing liquids to ensure that no liquid is spilled into
the inside of the scale or into connections on the rear of the equipment or the
power adapter. If liquid is spilled on the scale, it must immediately be unplugged
from the main electricity supply (pull out power adapter).
The weighing scale may be operated after it has first been inspected by a service
technician.
These operating instructions must be read by each user and should be easily
accessible at the workplace at all times.

Rev 2, 10.21.2016
7
Weight Scale
Construction & Functions
The weighing scale consists of the following parts
Electronic
height ruler
Indicator
Weighing
platform
Stand –
vertical rod

Rev 2, 10.21.2016
8
Functions
The Physician Scales are high-quality electronic precision weighing scales with
counting function and the following specifications
Model number
Capacity
Graduation
Weighing pan Size
Physician Scale
0-200kg
0.1 kg
13 in x 19 in
0-400lb
0.2lb
330mm x 480 mm
200 cm
0.5cm
7 ft 1 in0
0.5in
Net/Gross weight
Platform & Indicator
12.5 kg / 27.6 lb
37 X 15 X 68 cm / 14.6 X 5.9 X 26.8 in
Height Rod
4.8 kg / 10.6 lb
22 X 15 X 14.2 cm / 8.7 X 5.9 X 55.9 in
Package
Two carton boxes per set
50x9x7 in (box 1)
27x16x6 (box2)
(Standard carton)
Package
(Master carton)
Operating Temp.
<85%RH
Storing Temp.
32-104 F
Power source
4 x D dry cell and/or 5V from
USB
Power Consumption
20mA
Continuous Running Time
300 hours
Based on 6A/h battery

Rev 2, 10.21.2016
9
Features
•bar graph display
•2) Weight display

•3) Battery level

•4) Weight unit

•5) Height unit

•6) Height display

•7) Age display

•8) BMI display

•9) User number

•10) Symbol for sex




Figure: Details of your weighing scale
2 3
4
5
6
9
7
8
Keyboard

Rev 2, 10.21.2016
10
Application & Conformity
The Following are instructions of how to correctly use the weight scale:
The weighing scale may only be used for the weighing of solid-materials and of liquids
filled into secure containers.
The maximum capacity load of the weighing scale must never be exceeded, otherwise
the weighing scale may be damaged.
In using the weighing scale in combination with other devices as well as with devices
produced by other manufacturers, the appropriate regulations for the safe use of the
relevant attachments and their application in accordance with instructions must be
observed.
The weighing scale has been manufactured and tested in accordance with the
standards and recommendations set out in the declaration of conformity.
The power adapter supplied for the weighing scale complies with the appropriate
electrical protection class.
The following applies to the Physician Scale
Power supply:
1. Four pieces of D type cell battery and/or 5V form USB can be used.
2. When USB is connected, the scale will use 5V form USB only. (Although it can be used
for either power from battery or USB but it needs the battery to maintain the date and
time setting after switching off.)
Allowable ambient conditions
Temperature: 5°C - 40°C
Relative humidity: 25% - 85%, non-condensing
If you have any questions on the technical data or require detailed technical
information on your balance, please contact your technical representative.

Rev 2, 10.21.2016
11
Getting started
The scale is packaged in an environmentally-friendly carton, which provides optimum
protection for the balance during transportation.
We suggest that you keep the original packaging in order to avoid damage if you are
shipping or transporting the scale to a different location. It is also the best way to keep it
in the best conditions if it will not be used for an extended period of time.
In order to avoid damage, please follow the instructions provided below, when
unpacking the scale:
•Unpack the scale carefully.
•When outside temperatures are very low, the scale should be stored for a couple
hours and kept in its box in a dry room at normal temperature, so that no
condensation settles on the unit when opening the box.
•Check the scale immediately after unpacking for any external visual damage. If
there is any damage on scale, contact customer service immediately.
•If the scale is not to be used immediately after purchase, it should be stored in a
dry place where fluctuations in temperature are low. (Reference pg.23).
•Read through these operating instruction, before you work with the unit and pay
attention to the Safety recommendations (reference Safety pg. 6).
Delivery
Inspect delivery for completeness immediately on unpacking all components.
Checklist for complete delivery
Component delivered present yes / no
Electronic ruler
Indicator/Rod
Weighing Platform
Operating manual

Rev 2, 10.21.2016
12
Assembly & Installation
The weighing scale is delivered in a partly dismantled condition. Assemble the individual
components in the following sequence:
 Find the carton with same number mark. Open it, check the number on the height rod, indicator
and platform, if they are same, then you can start install.






















2. UseAllen key to take out the four pieces fixed screws




















Rev 2, 10.21.2016
13
3. Connect the load cell plug. (attention: connect in right direction, with proper force)






















4. Use the Allen key to fix the screws which have been taken out before. Then use the white plastic
oval cover to cover the screws.

























Rev 2, 10.21.2016
14


5. Make sure the no. on the indicator and platform is same, connect the plugs between indicator and
height rod.,(Attention: make sure they are in right direction, with proper force.)
6. Install the indicator according to below picture, insert the extra wire inside the rod., then push
down the indicator until you hear clicking sounds, means you have finished the installation for
the indicator.

Rev 2, 10.21.2016
15
7. Use the Philips screwdriver to take off this two screws on the slide rod
8. Put the top lever into the height rod. Make sure the direction is right.

Rev 2, 10.21.2016
16
9. Use the Philips screwdriver to fix the screws which have been taken offer before.
10. Start using it after you finish the installation.

Rev 2, 10.21.2016
17
The following Safety recommendations must be observed when connecting the scale:
The Scale should only be connected to the mains voltage socket with the power adapter
supplied. Check before connecting the power adapter to the mains socket, that the
operating voltage stated on the power adapter complies with the local mains voltage.
If the operating voltage is not the same as the mains voltage, the power adapter must
not be connected to the mains socket and contact customer service.
Placement of Scale
The location in which the scale is placed is very important in order for the scale to work
to its full potential. Certain conditions can affect the capabilities of the scale, conditions
like: the presence of air flow, variations in temperature, and direct sunlight. Please
follow the recommendations given below in choosing a location to place your scale.
•Place the scale on a solid, firm and preferably vibration-proof, horizontal base
•Make sure that the weighing machine cannot be shaken or knocked over
•Protect from direct solar radiation
•Avoid drafts and excessive temperature fluctuations
•Avoid placing the scale near or on any magnetic surfaces.

Rev 2, 10.21.2016
18
OPERATION
6.1) turn on after making sure the batteries and/or USB is in normal working condition, remove
if anything on the weighing platform, press “On/Off”to turn on the physician scale, after
indicator is on it will display current date and time for about 2 seconds, then it will get in to
operation mode, for example, if date & time is 2 Jan 2014 & 3 o’clock 4 minutes 5 seconds AM,
the display will show as below.
The scale has auto zero function to reset zero when power on, but only if the weight on
platform is below 10kg.
6.2) turn off
During operation mode, press On/Off to turn off the scale, or it will turn off automatically
if the scale is not in use for about 5 minutes, before the display goes off, it will show as below:
6.3) check or set date & time
If checking, press “Date/time” it will display current date & time for about 2 seconds, for
example, if date & time is 2 Jan 2014 & 3 o’clock 4 minutes, 5 seconds AM, display will show
as below:
Sec
Hour
Day Minute
Month

Rev 2, 10.21.2016
19
For setting, during checking mode, press and hold “Date/time” until beeper sounds then
release, year digits flash, press“Date/time” to confirm, month digits flash, press “Date/time” to
confirm ,day digits flash, press“Date/time”to confirm, hour digits flash, press “Date/time”to
confirm, minutes digits flash, press “Date/time”to confirm, second digits flash, press
“Date/time” to confirm, then setting is finished, press“▲/Up or ▼/Down” to change digits
while it is flashing.
6.4) selecting user number
Press “▲/Up or ▼/Down” to select user number during operation mode. (user number
start from 0 to 99, total 100 numbers, each user number contents 15 records, except number 0,
there is no hold & save function.)
6.5) Setting sex and/or age
During operation mode, press User then symbol of sex flash, press “ ▲/Up or
▼/Down” to select, “ ” for male“ ”for female, press “user” to confirm, then age digits flash,
press “ ▲/Up or ▼/Down” to set age, press User to confirm.
6.6) Zero the weight & height
During operation mode, remove everything on weighing platform and pull down height
ruler to bottom, press “Zero” which will reset the reading to zero for weight, to minimum for
height, only if the scale is within 50kg of zero range & 5cm of minimum range reading.
After setting zero it will show one of the following four displays:
1) means setting of weight & height both pass.
2) means setting of weight pass but height fail.
3) means setting of weight fail but height pass.
4) means setting of weight & height both fail.
12
34

Rev 2, 10.21.2016
20
6.7) Saving data
During operation mode and not in user number 0, BMI reading >10.0, after weight &
height reading both stable, “Hold” will display, press
Save to save data, “Save” will display, it means data is saved, once user leave the platform, it
returns back to operation mode.
6.8) change the units of weight & height
During operation mode, press Weight to switch kg or lb.
Press Height to switch cm or FT.
6.9) getting data of weight, height & BMI
Zero the weight & height, input user number, age & sex, push up ruler to more than
user’s height, stand straight in middle of platform, pull down ruler to tough use’s head, when kg
or lb and cm or FT stop flashing, “Hold” will display, press“Save” to save data, if not the “Hold”
will be reset after user left platform. Following is the data display of a user: male, user number
99, BMI 23.3, age 15, height 159.4cm & weight 59.4kg.
6.10) check records of specific user
Use “▲/Up or ▼/Down”to select user number, press and hold “Save until BMI bar
graph goes off then release, one of the bar will flash, use “▲/Up or ▼/Down”to search
specific record, press “Zero” to delete record of the flashing bar, press “Date/Time”to
read the date & time of flashing bar, press “save” to return back operation mode. As
shown below: