Lumena ProSolar OLYMPIA User manual

Full product range & more information: www.lumenalights.com
USER MANUAL
OLYMPIA Professional Solar Pedestal Light
THANK YOU FOR YOUR PURCHASE
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION / MAINTENANCE
WARNINGS
•If a fitting is found to be damaged, cease use immediately.
•The unit may get warm whilst on for a period of time.
•Always take care when installing your solar light.
•Fitting must be mounted to a solid surface or using relevant anchor bolts / J-Bolts
•This Solar Light will not charge correctly if the panel is behind glass or artificial light is used.
•Ensure the waterproof bung is in place at all times, other than when turning the unit on.
•Due to temperature difference in and outside the fitting, condensation may be present internally but will not affect use.
CLEANING & MAINTENANCE:
Occasional cleaning and care is recommended for this product. Wipe with a soft, slightly damp cloth to remove any surface dirt.
To maintain efficiency, specifically clean the solar panel and polycarbonate lens on a regular basis. Also, keep the solar panel free
of debris and snow to prevent reduced battery life or malfunction. Do not use abrasive cleaners or a lot of water as this could
damage the fitting. Please refer to our website for more information on the best way to clean different materials.
RETURNS:
If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email:
Lumena Lights Ltd, Centre 33 Long March, Daventry, NN11 4NR Tel: [phone] Email: [e-mail]
Our full returns policy is available on our website.
Waste Electrical Products should not be disposed of with household waste. Please check with your local authority or contact us
for more information. Please recycle packaging whenever possible.
Producer Registration Number: WEE/KC3440XY
SPECIFICATIONS
Wattage: 3.5W
Lamp: In-built Epistar LED Chips 10 *18 mil (120˚ Beam Angle)
Colour Temperature: 3000K (Warm White) / 6000K (Daylight White)
Lumen Output: Approx. 420 lm
LED Life Expectancy: up to 50,000 hours
Sensor: Photocell (Dusk to Dawn)
IP Rating: IP65
Battery Type: Lithium - LiFePO4 6.4v/5000mAh (replaceable)
Battery Charge Time: 6-8 hrs full sunshine (approx.)
Max Illumination Time at Full Charge: Up to 23hrs
Solar Panel: 9v / 5.5W Monocrystalline Solar Panel –Grade A
Materials: 6063 Die Cast Aluminium & Polycarbonate
Weight: 2.5KG (approx.)
Mounting: Internal Surface Mount
Lighting Function:1hr 100% + 2hrs 80% + 2hrs 50% + 9hrs 30%
Working Temperature: -25˚C ~ 55˚C
Included: Bollard, Rubber Bung, Anchor Bolts
✔✔✔
3 YEAR
GUARANTEE
see website for
more details
260mm
380mm
120mm

Full product range & more information: www.lumenalights.com
OLYMPIA TECHNOLOGY:
The Olympia is a highly efficient solar light with high capacity LiFePO4 Lithium batteries and a fast charging Monocrystalline solar
panel. This means that even on cloudy and rainy days, it will re-charge efficiently. The high battery capacity gives enough power
for up to 23 hrs solid light (approx. 2-3 nights) even when there is little light during the day. The high lumen light output is bright
enough to illuminate driveways and paths, making them safe to navigate at night, with a downward spread light projection.
INSTALLATION:
Designed to be mounted on a low wall, wood, patio or set in concrete (J-Bolts sold separately) via the internal surface mount.
Recommended spacing is 3m apart for substantial lighting. Closer spacing / staggering will result in a more
intense light.
Location –It is important that the installation location is carefully considered,
avoiding shady areas. Ensure there is no other lights which could interfere with the
dusk to dawn sensors, located in the solar panel, imitating daylight.
1. To surface mount, remove the internal base from the bollard by unscrewing
the 3 x cross head screws at the bottom of the tube, then lift off.
2. Use the base to mark the mounting holes on the mounting surface in the
desired location.
3. Remove the mounting plate and drill out the 3 holes marked (12mm if using
anchor bolts supplied), at least 70mm depth (anchor bolt sleeve = 60mm).
Alternative mounting screws may be required depending on the surface –adjust drilling size accordingly).
4. Insert anchor bolts with sleeve (head down / thread pointing upwards). Then place internal mounting base over the top.
NOTE: bolts may need to be knocked in fully with a hammer / mallet –be careful not to damage the
thread. If too tight, attach to base with nut first (step 5) and knock into position after.
5. Add the large washers and the spring washer on each bolt and secure in place with nut by hand.
6. Tighten the nut fully with a spanner to expand the bolts and hold in place securely.
7. Replace the bollard body, lining up the 3 x holes at the base.
8. Replace the 3 cross head screws removed in point one to secure in place.
SETTINGS:
The Olympia has a pre-set time controlled setting which cannot be changed. At dusk, the bollard will illuminate at full brightness,
and then follow a gradual dimming sequence until it reaches 30% brightness after 5 hours. From then on it will remain at 30%
until dawn. This sequence is to ensure the maximum charge is retained.
IMPORTANT –SOLAR PEDESTAL LIGHT MUST BE TURNED ON AT ALL TIMES AFTER INSTALLATION
If the pedestal light is left in the off position, you will be prompted to turn the fitting on by strobing.
Solar pedestal will only charge when in the ON position.
Turning on the pedestal light
1) Remove the waterproof rubber bung located just below the polycarbonate lens, in line with the Lumena Logo, to locate
the red on/off button.
2) Using a small, flathead screwdriver (or similar), push the on button inwards until it clicks and allow to pop back out
(this will be partial). The pedestal is now in the ON position.
3) Replace the waterproof, rubber bung.
4) To turn off for storage, repeat the same procedure as above.
NOTE: There will be a 2-5 second delay between turning the solar light on, and the pedestal illuminating. In daylight, the light
will turn back off within a few seconds, in darkness it will remain on and follow the time-controlled cycle.
STORAGE:
When storing the pedestal light, be sure to turn the pedestal to the off position by following the above steps. Once pressed, the
on/off button will release fully forward. Max 6 months storage when fully charged –recharge will be required periodically to
prevent damage to battery over long periods of time.
Depth 8mm
60mm
13mm
120mm
68mm