Lumena PROSOLAR SECURBOL User manual

Full product range & more information: www.lumenalights.com
USER MANUAL - SECURBOL
Adjustable 800mm Radiata Pine Solar Path Light
with PIR Sensor
THANK YOU FOR YOUR PURCHASE
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION / MAINTENANCE
WARNINGS
•If a fitting is found to be damaged, cease use immediately.
•The unit may get warm whilst on for a period of time.
•Always take care when installing your solar light.
•Ensure the fitting is mounted out of range of head height to avoid injury.
•Fitting must be installed as per the installation instructions or guarantee will be void.
•This Solar Light will not charge correctly if the panel is behind glass or artificial light is used.
CLEANING & MAINTENANCE:
Occasional cleaning and care are recommended for this product. Wipe with a soft, slightly damp cloth to remove any surface
dirt. To maintain efficiency, specifically clean the solar panel, LEDs and PIR on a regular basis. Also, keep the solar panel free of
debris and snow to prevent reduced battery life or malfunction. Do not use abrasive cleaners or a lot of water as this could
damage the fitting. Please refer to our website for more information on the best way to clean different materials.
RETURNS:
If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email:
Lumena Lights Ltd, Centre 33 Long March, Daventry, NN11 4NR Tel: [phone] Email: [e-mail]
Our full returns policy is available on our website.
Waste Electrical Products should not be disposed of with household waste. Please check with your local authority or contact us
for more information. Please recycle packaging whenever possible.
Producer Registration Numbers: WEE/KC3440XY / BPRN0843
SPECIFICATIONS
Wattage: 7W
Lamp: In-built LED SMD 2835 40 + 10pcs (100˚ Beam Angle)
Colour Temperature: Main = 6000K (Daylight) & Wall Wash = 3000K (Warm)
Lumen Output: 700 lm
LED Life Expectancy: up to 35,000 hours
Sensor: PIR (Motion Sensor) + Photocell (Dusk to Dawn)
IP Rating: IP65
PIR Detection Range: up to 2m 120˚ beam angle
PIR Sensor Delay Time: approx. 20 seconds
Battery Type: Lithium Ion 18650 3.7v/5400mAh (replaceable)
Battery Charge Time: up to 12 hours (approx.)
Solar Panel: 7W = 3.7Wp Polycrystalline Silicon –Adjustable by 70˚
Max Illumination Time at Full Charge: 20hrs > 6 nights (varies by function)
Materials: ABS, Polycarbonate, Glass Solar Panel, Radiata Pine (pressure treated)
Weight: 9KG (approx.)
Mounting: Root Mounting
Path Light Height: 1200mm (400mm to be buried under ground)
✔✔✔
3 YEAR
GUARANTEE
see website for
more details

Full product range & more information: www.lumenalights.com
SECURBOL TECHNOLOGY:
The Securbol is a highly efficient solar light with high capacity Lithium Ion batteries and a fast charging Polycrystalline solar panel.
This means that even on cloudy and rainy days, it will re-charge efficiently. The high battery capacity gives enough power for up
to 6 nights in standard PIR mode, even when there is little light during the day. The high lumen light output is bright enough to
illuminate driveways and paths, making them safe to navigate at night.
INSTALLATION:
The Securbol is designed to be root-mounted into wet concrete or buried securely into compact earth. For extra stability, attach a large
wood screw into two sides of the sleeper approximately 200mm from the base. These will act as anchors when set into wet concrete.
Location –It is important that the installation location is carefully considered, avoiding shady areas. The best position is south
facing; however, the light can work facing in other directions, especially when in full sunshine. The PIR must face the direction in
which the motion is to be detected. Ensure there is no other lights which could interfere with the Sensors, imitating daylight.
1. Prepare a mounting hole in the desired location to allow for a sleeper
depth of at least 300-400mm (can vary depending on the required
height above ground). Ensure the hole is at least 300mm x 50mm to
accommodate the width of the sleeper (220mm x 40mm), or slightly
more if anchors are attached (see above). TIP: Carry out placement
check prior to final installation into wet concrete.
2. Mount the sleeper into the desired location using supports to hold
the fitting upright. Concrete or earth must cover the anchor and at
least 100mm above.
3. Remove small screw from side of mounting bracket attached to
sleeper.
4. Line the solar light up with the 4 keyhole holes and then push the
fitting downwards to fix in position.
5. Secure front of the light in position by replacing and fastening the side
screw removed in point 3.
6. Adjust solar panel accordingly & select desired working mode.
MODES / SETTINGS:
The Securbol has 3 different settings / modes, as well as an override “OFF” mode. All modes will only function during darkness /
dusk.
Before use, remove the battery release tab from the remote control.
For first use, press the “ON” button on the solar light control panel to activate the light and remote.
To switch between modes, select the relevant button for the desired setting after installation. When a new mode is selected
successfully, the fitting will flash once.
Modes can be changed via the remote control, up to 10m, or on the fitting. Lift the solar panel to locate the control panel.
Remote control can control more than one fitting in range.
To adjust the solar panel position, slightly loosen the top cross-head screws on both sides of the fitting. Adjust panel to desired
position in direct sunlight and retighten screws to secure. Adjust to approx. 45 degrees for maximum charge effectiveness.
Point 5
Point 3
Point 4