Lumilum LUM-RGBUX8 User manual

PRODUCT FEATURES:
USES:
©Lumilum LED Lighting (305)-233-2844
www.lumilum.com
Page 1 of 5
LUMILUM 120V LED LIGHT STRIP
UX8 COLOR WHEEL
CONTROL TOUCH PANEL
LED MADE SIMPLE.
SKU: LUM-RGBUX8
4 Zone Color Control
Input: 5VDC, 0.5A-1A (w/ included transformer)
Output: 120VDC
Output Signal: RF 2.4 GHz, DMX512
DMX Signal Input Connections:
3 or 5-pin DMX (XLR), Cat 5 (RJ45), Cat 6 Cables
DMX Signal Thru Connections:
3 or 5-pin DMX (XLR), Cat 5 (RJ45), Cat 6 Cables
Product Dimensions: 5.75” x 4.17” x 0.73”
Shipping Dimensions: 16” x 11.03”x 5.71”
Weight: 8 oz
Operating Temperature: -22°F ~131°F
Not Reccomended for Outdoor Use
WARRANTY
3 YEAR

©Lumilum LED Lighting (305)-233-2844
www.lumilum.com
Page 2 of 5
PRODUCT SIZE:
TERMINALS:
50mm
28mm
24
mm
57mm
4mm
47.5mm
106mm
60mm
46mm
18mm
7mm
7mm
10.5mm
30mm
60mm
83.5mm
146mm
OFF ON
1: DMX+
2: DMX-
3: NC
4: Power
5: Power
6: NC
7: GND
8: GND
Signal Interface
DMX RJ45
1...... 8
DMX
OUT
DC+
5V
Power Input DMX Signal Output
DC- GND DMX+DMX-
Slot
Reset Key
Power Indicator The Running Light
USB Input

BUTTON FUNCTIONS DIAGRAM:
©Lumilum LED Lighting (305)-233-2844
www.lumilum.com
Page 3 of 5
Zones
On/Off
Pre-Programmed Modes
1. Static Red
3. Static Blue
5. Static Purple
7. Static White
9. 7 Colors Jumping
11. 7 Colors Smooth
2. Static Green
4. Static Yellow
6. Static Cyan
8. RGB Jumping
10. RGB Smooth
Saved Scenes
RGBW White Control
*Not Supported By Lumilum Strips
Touchable Color Wheel
Speed/Brightness
HOW TO USE COLOR WHEEL CONTROL PANEL (LUM-RGBUX8)
Upon initialization all buttons will be illuminated - press zone number to deselect.
Set up the first zone by pressing Z1 and choose your color or mode function. When adding a second strip to the
DMX module that is to be independently controlled, add another zone switch your DMX to ADD2, press button
4/enter, and toggle using buttons 2 and 3 until you reach a secondary zone address (A--5, A--9, A-13)

INSTALLATION INSTRUCTIONS:
©Lumilum LED Lighting (305)-233-2844
www.lumilum.com
Page 4 of 5
1. Install the back box into the wall, these are some
examples of typical back boxes:
3. Screw the base plate and the back box securly
into the wall:
2. Use a straight screwdriver to pry the postion
shown below:
4. Connect the black and red wires and put the
power adapter in the back box:
5. Embed the upper touch panel into the
baseplate and then tap the bottom to press into
the slots:
Slot
DMX Signal Output
Power Input 5Vdc
Power Adapter
ZONE
SAVE
SAVESAVESAVE
ZONEZONEZONE
ZONE
ZONE
ZONE
ZONE
SAVE
SAVE
SAVE
SAVE
Touch Panel
Baseplate
Base

Can be used with the following Lumilum products
for low voltage installations:
LUM-DMX212 4X8A (768W @24V)
LUM-DMXWP2 (IP65) 4X5A (480W @ 24V)
*Remote LUM-RGBUX8-RC
ON/OFF functions only for zones
Color Wheel Control Panel
*Remote
©Lumilum LED Lighting (305)-233-2844
www.lumilum.com
Page 5 of 5
DMX OUTPUT WIRING:
RF WIRELESS WIRING:
DMX IN DMX OUT
DMX DECODER
OUTPUT
POWER
DMX Input
12-24Vdc
RGBW Strip
DMX Address = 1
Zone 1
DMX
Output
DMX Address = 5
Zone 2
DMX Address = 9
Zone 3
12-24Vdc
DMX Address = 13
Zone 4
DMX IN DMX OUT
DMX DECODER
OUTPUT
POWER
12-24Vdc
RGBW Strip
DMX IN DMX OUT
DMX DECODER
OUTPUT
POWER
12-24Vdc
RGBW Strip
DMX IN DMX OUT
DMX DECODER
OUTPUT
POWER
RGBW Strip
+ R G B
+ R G B
5-24Vdc
RGBW Strip
LED RGB CONTROLER
MODEL:RFCPRX53
POWER INPUT: DC12V-DC24V OUTPUT:3Ax3CH
wire preparation
CO MP AC T