Lumiring Technology LR-1C Series User manual

LRE-1CR
LRM-1CR
LR-1CB
LRE-1CRS
LR-1CBS
LR-1C Series
Standalone Access Solution
User Manual
VIDEO MANUAL
LR-1C Series

1
2
2
4
4
6
8
12
12
14
16
17
19
20
22
23
25
26
28
29
31
32
34
INTRODUCTION
FEATURES
MAIN SPECIFICATION
CARTON INVENTORY
INSTALLATION
JUMPER SETTINGS
CONNECTION DIAGRAMM
ADD MASTER CARD
ADD USER CARD
DELETE USER CARD
DELETE ALL USER CARDS
ADD BOSS CARDS
DELETE BOSS CARD
DELETE ALL BOSS CARDS
ADD SECURITY CARDS
DELETE SECURITY CARD
DELETE ALL SECURITY CARDS
CHANGE STAND-BY THEME
CHANGE REACTION THEME
CHANGE LOCK WORK TIME
AUTOMATIC CARD ADD MODE
POSSIBILITIES OF BOSS CARD
POSSIBILITIES OF SECURITY CARD
CONTENTS

INTRODUCTION
01
The LR-1C its series of standalone access controllers with dier-
ent features: embed rd reader, embed NO-TOUCH button, em-
bed Radio Receiver 433 Mhz etc. All standalone controllers from
this series have RGB Lumiring indicator which used for work with
Lumiring menu.
By Lumiring Menu customer can:
ADD USER CARDS (1-2000)
DELETE ONE USER CARD
DELETE ALL USER CARDS
ADD BOSS CARDS (1-10)
DELETE ONE BOSS CARD
DELETE ALL BOSS CARDS
ADD SECURITY CARDS (1-3)
DELETE ONE SECURITY CARD
DELETE ALL SECURITY CARDS
CHOOSE STAND-BY INDICATION THEME (1-4)
CHOOSE REACTION INDICATION THEME (1-4)
CHOOSE TIME FOR LOCK WORK (1-255 s)
SET CONTROLLER TO CARD AUTO ADD MODE
All this work users can do without any tools in any time if have in
hand only MASTER CARD. Master cards must be set at rst system
start or after full hardware reset. One controller can support up
to 3 master cards.

FEATURES
MAIN SPECIFICATION
02
Static protection.
Reverse power protection.
Power protection.
Waterproof coat, conforms to IP 56 (IP65*)
Industrial grade components.
Security screw.
Safe wall mount.
Autodetect Wiegand 26 / 34 bits.
Full color RGB ring indicator.
4 Stand-By indication themes.
4 Work indication themes.
Low temperature resistance ( -30 C).
3 Lock work modes.
* By special order device will be made without terminal block with cable.
Memory: 2048 codes (special version up to
15 000)
Memory type: EEPROM, non-volatile
Critical event protection: Watch Dog, Power On Reset
Relay NC/NO: 1 (Control mode:Trigger, Pulse,
Monostable)
Relay operation time
control: 1-255 seconds, 3 seconds default
Relay Specication: 2A - continuous operation; 10A -
pulse mode
Door control input: 1 (Door not closed control, Breaking
open control)

03
Exit button input: 1 (Free/Card entry switching by long
press - 10 seconds)
Alarm out: 1 0,5A max
Power supply: 9-24VDC
Indicator: RGB light ring & Beeper
Visual themes: 4 stand-by, 4 reaction
Reader frequency: 125kHz or 13.56Mhz (option)
Standard 125kHz: EMMARINE
Standard 13.56MHz: ISO14443A
Reading range 125kHz: 6-12cm
Reading range
13.56MHz: 3-8cm
Supported Tage 125kHz: EM 4001 / EM 4012 / HID ISOProx II /
HID ProxCard II / TEMIC
Power Consumption: < 1W
Communication
Interface:
Autodetect Wiegand 26-34 bits /
W-BUS
If you need more detail specication for each device please
visit our site or download catalogue:
WEBSITE CATALOGUE

CARTON INVENTORY
INSTALLATION
04
Wall Anchors
Fast diode 1N4973
Self Tapping Screws
Allen wrench key Jumper connector
Security screw
LRE-1CR
LRM-1CR
LR-1CB
LRE-1CRS
LR-1CBS
Reader options
Remove the back cover from the unit.
Drill 4( A, B, C, D) holes or 2 any diagonal holes.
Put the supplied wall anchor in holes.
Put connection cable through cable window in back cover.
Fix the back cover rmly on the wall with 4 at head screws.
Attach wires in cable to terminal block by connection diagram.
Set necessary settings by jumpers.
Attach unit to the back cover and x by supplied security screw.
Power on device.

JUMPER SETTINGS
05

JUMPER SETTINGS
06
X1 JUMPER SETTINGS & SW1 DIP-SWITCH SETTINGS.
RELAY WORK MODES
JUMPER SET DIP SWITCH SETTING
1-2 OFF
3-4 OFF
1 -OFF
2 -OFF
Trigger mode
(default)
1-2 ON
3-4 OFF
1 -ON
2 -OFF Bistable mode
1-2 OFF
3-4 ON
1 -OFF
2 -ON
Monostable
mode
1-2 ON
3-4 ON
1 -ON
2 -ON Reserved
READER INTERFACE SETTINGS
JUMPER SET DIP SWITCH SETTING
7-8 OFF 3 -OFF W-BUS
(default)
7-8 ON 3 -ON Wiegand 26-34
AutoDetect
RELAY OUTPUT SETTINGS
JUMPER SET DIP SWITCH SETTING
9-10 OFF 4 -OFF Normally open
relay (default)
9-10 ON 4 -ON Normally closed
relay

07
DOOR CONTROL SETTINGS
JUMPER SET DIP SWITCH SETTING
11-12 OFF Without door control
sensor (default)
11-12 ON With door
sensor
HARDWARE RESET
JUMPER SET DIP SWITCH SETTING
4-6 OFF 6-OFF Work mode
(default)
4-6 ON 6-ON Hardware
reset

08
CONNECTION DIAGRAMM
LRE-1CR / LRM-1CR
ALTERNATIVE DIAGRAM FOR CONNECT
3RD PARTY READER (6 WIRES)